KNX Touch sensor module Standard
Ref.-no.: 207x TSM
Operating Instructions
Touch sensor module Standard
1-channel, 2-channel, 3-channel, 4-channel
1. Safety warnings
Attention: Electrical equipment must be installed and fitted by
qualified electricians only.
Failure to observe any of the installation instructions may cause
damage to the device and result in fire or other hazards.
2. System Information
This device is a product of the KNX/EIB system and complies with KNX
directives.
Detailed technical knowledge obtained in KNX/EIB training courses is a
prerequisite to proper understanding. The functionality of this device
depends on the software.
Detailed information on loadable software and attainable functionality as
well as the software itself can be obtained from the manufacturer’s
product database.
Planning, installation and commissioning of the unit is effected by means
of KNX-certified software.
An updated version of the product database and the technical
descriptions are available in the Internet at www.jung.de.
Stand: Jul-08 825 586 03
KNX Touch sensor module Standard
Ref.-no.: 207x TSM
3. Function
A touch sensor rocker is „divided“ into an upper and a lower half (FIG A)
each controlling a function such as switching, dimming, shutter, value
transmitter, recalling and storing of light-scenes. Each rocker is equipped
with a red status LED. A blue operation LED can serve as an orientation
light.
Function assignment:
upper half of rocker: On / Brighter / Up
upper half of rocker: Off / Darker / Down
Together with the wall-mounted radio-control transmitter, Art. no. 40 FW,
the device can also be used within the JUNG-Funk-Management system.
More details are set out in the technical documentation of the
wallmounted radio-control transmitter.
The device must be equipped with the corresponding touch sensor
module covers (must be ordered separately):
1 channel 2071 TSM 1 x FD..901 TSA..
2 channel 2072 TSM 2 x FD..902 TSA..
3 channel 2073 TSM 1 x FD..902 TSA.. und 2 x FD..904 TSA..
4 channel 2074 TSM 4 x FD..904 TSA..
1 2
3 4
1
2
3
1
1 2
2
KNX Touch sensor module Standard
Ref.-no.: 207x TSM
4. Installation
(1)
(2)
(3)
(4)
(5)
(1a)
• Connect the KNX/EIB bus coupler (1) to the KNX/ EIB bus and
install it in a flush-mounting box. If possible, program the physical
address beforehand into the coupler. (Within the JUNG FunkManagement system: wall-mounted radio-control transmitter)
• Plug the touch sensor module (3) together with the decorative
frame (2) on the KNX/EIB bus coupler so that both devices are
connected via the user interface connector (1a).
• Fasten the touch sensor module with the plastic screws supplied (4)
to the KNX/EIB bus coupler. The screws are intended as a
protection against removal or theft. Tighten the plastic screws only
lightly (!). (Not possible with wall-mounted radiocontrol transmitter.)
IMPORTANT: Use only the plastic screws supplied with the device
for fastening! Metal screws are not permitted. The device may else
be irreparably damaged by electrostatic discharges! ·
• Fit the covers (5): Place the covers one by one on the touch sensor
module. The arrangement of the covers is shown in FIG A. Make
sure the cover fits properly (observe the marking TOP on the
inside) and snap it onto the device by a brief press.
4.1. Label covers
The covers with Art. no. FD..90x TSA NA.. can be equipped with labels.
Commercial-grade transparencies can be inscribed with the help of the
JUNG labelling software and inserted as labels into the covers.
3
KNX Touch sensor module Standard
Ref.-no.: 207x TSM
The JUNG labelling software is available in the Internet under the
following address:
www.jung-beschriftungsservice.de. Fit the label covers as shown in FIG
C.
5. Technical data
Supply: 21 – 32 V DC via flush-mounted
BCU
Connection: 2 x 5-polig user interface connector
Power consumption: max. 150 mW plugged into
standard BCU
Type of protection: IP 20
Safety class: III
Ambient temperature: -5 °C … +45 °C
Storage/transport temp.: -25 °C … +70 °C
Technical specifications subject to change.
6. Guarantee
Our products are under guarantee within the scope of the statutory
provisions.
Please return the unit postage paid to our central service
department giving a brief description of the fault:
ALBRECHT JUNG GMBH & CO. KG
Service-Center
Kupferstr. 17-19
D-44532 Lünen
Service-Line: +(49) 23 55 . 80 65 51
Telefax: +(49) 23 55 . 80 61 65
E-Mail: mail.vka@jung.de
General equipment
Service-Line: +(49) 23 55 . 80 65 55
Telefax: +(49) 23 55 . 80 62 55
E-Mail: mail.vkm@jung.de
KNX equipment
Service-Line: +(49) 23 55 . 80 65 56
Telefax: +(49) 23 55 . 80 62 55
E-Mail: mail.vkm@jung.de
The
-Sign is a free trade sign addressed exclusively to the
authorities and does not include any warranty of any properties.
4
Loading...