JumpSport PowerBounce PowerPack 20, POW-S-10998A, POW-S-21544-00, PowerBounce PowerPack 48, POW-S-10998-01 Assembly And Installation Instructions Manual

PowerBounce

User’s Manual

Assembly, Installation, Care, Maintenance, and Use

Instructions

WARNING

Read these materials prior to assembling and using

the trampoline and Trampoline Enclosure

1) PowerBounce Kit to be used only with designated JumpSport and AlleyOop Sports trampolines.

2) Use of a JumpSport or AlleyOop Sports Safety Enclosure is STRONGLY recommended.

3) Follow all warnings and safety tips provided with your trampoline and safety enclosure.

Retain address information for future use.

JumpSport, Inc.
1680 Dell Ave.
Campbell, CA 95008 U.S.A.

DO NOT attempt or allow
somersaults. Landing on the
head or neck can cause serious
injury, paralysis or death, even
when landing in the middle of the
bed.

Use trampoline only with mature, knowledgeable supervision.

DO NOT attempt to jump over
the barrier.

PowerPack 48

DO NOT allow more than one
person on the trampoline. DO
NOT allow more than one
person inside the trampoline
enclosure. Use by more than
one person at the same time
can result in serious injury.

DO NOT intentionally rebound
off the barrier.

DO NOT hang from, kick, cut
or climb on the barrier.

The maximum user weight is:

PowerPack 20

—JSE 14ft, AO 12ft & AO 14ft VB: 260 / 260 / 270 pounds

—JS 12ft & AO 10ft: 245 / 235 pounds

PowerPack 32

PowerPack 64

—JS 14ft: 255 pounds

—AO 14ft DB: 300 pounds

408-213-2551

www.jumpsport.com

1

P/N: INS-P-10613F

Copyright Notice

This material is protected by the United States copyright laws and is proprietary to JumpSport, Inc. Disclosure, reproduction,
translation, modification, or use of this document by anyone other than authorized employees, authorized users, or licensees of
JumpSport without the prior written consent of JumpSport, Inc. is prohibited.

The information in this document is subject to change without notice. JumpSport, Inc. shall not be liable for any damages resulting
from technical errors or omissions, which may be present in this document, or from use of this document.

Copyright © 2004-2018, by JumpSport, Inc. All rights reserved.

Printed: 2018

Instruction Manual P/N: INS-P-10613F

PowerPack 20 P/N: POW-S-10996A, POW-S-21544-00
PowerPack 32 P/N: POW-S-10997A
PowerPack 48 P/N: POW-S-10998A, POW-S-10998-01, POW-S-10998-01B
PowerPack 64 P/N: POW-S-10778A, POW-S-10778-01, POW-S-10778-01B

Trademarks

JumpSport®, AlleyOop Sports®, PowerBounce™, PowerSpring™, PowerArm™, and PowerHook™ are trademarks of JumpSport,
Inc.

All other brand or product names are trademarks or registered trademarks of their respective companies or organizations.

Patents

This product includes technology associated with one or more of the following U.S. Patents:

No. 6,053,845

No. 6,261,207

No. 6,840,891

No. 6,846,271

No. 7,060,001

Additional Patents Pending.

How to Contact Customer Support

Should you require customer service or technical support for your PowerBounce Trampoline, please contact JumpSport’s Customer
Service department at:

408-213-2551

6:00am—5:00pm Monday through Friday, Pacific Time

2

Assembly and Installation
Instructions

Thank you for purchasing a PowerBounce Trampoline!

The following pages contain diagrams, pictures, and written instructions for installing your PowerBounce PowerPack.

Familiarize yourself with the Assembly and Installation Instructions before beginning installation.

Parts List

Each PowerBounce Assembly is comprised of three parts:

A) PowerSpring

B) PowerArm

C) PowerHook

B

A

C

Parts

(Cut-away side-view of installed

PowerBounce Assembly)

3

Assembly and Installation Instructions

Step 1: Locate and become familiar with where the PowerBounce (PB) Assemblies will

be installed. Note that you may have extra PowerBounce assemblies when installation is
complete. Keep these as spares.

(These are the recommended configurations for each PowerBounce Trampoline. You can also
come up with your own configuration that works best for you!)

KEY:

= PB Assembly

= Original Spring
(with no PB Assembly)

PowerPack 20—fits JumpSport 12ft & AlleyOop 10ft
Install 1 PB Assembly on every fourth V-ring (leave three V

-rings/springs in-between – PB Assemblies can be installed
on either large or small V-rings). Note: you will have two
left over power bounce springs if you are installing on an
AlleyOop 10ft model.

PowerPack 32—fits JumpSport 14ft& JumpSport Elite 14ft

Install 1 PB Assembly on every third V-ring (leave two V­rings/springs in-between – half the PB Assemblies will be
installed on large V-rings and half on small V-rings).

Top Mat

PowerPack 48—fits AlleyOop 12ft & 14ft VariableBounce

Install 1 PB Assembly on every other V-ring (leave one V­ring/spring in-between – PB Assemblies can be installed
on either large or small V-rings). Note: you will have four
left over power bounce springs if you are installing on an
AlleyOop 12ft model.

PowerPack 64—fits AlleyOop 14ft DoubleBounce

 Top mat: 2 adjacent springs will have a PB assembly

installed on them, the next spring will have no PB, the
next 2 adjacent springs will have a PB assembly, etc.

 Bottom mat: Do not install any PB Assemblies on the

bottom mat.

 Half the PB Assemblies will be installed on large V-

rings and half on small V-rings.

4

V-ring

Assembly and Installation Instructions

Picture A

B

Horizontal head

of PowerArm

Picture B

Picture C

2) Completely remove an existing spring. Insert a PowerArm (A) into the V-ring (see Picture A). Position the horizontal head (top) of

the PowerArm along one side of the V-ring (see Picture B), point the tip of the V-ring up into the air, and rotate the PowerArm into
place around the tip of the V-ring. The head of the PowerArm will then be locked under the tip of the V-ring so that it is firmly held in
place, (see Picture C).

IMPORTANT: The horizontal head needs to go under the tip of the V-ring (see Picture C). If you can push the PowerArm up
through the V-ring, then the PowerArm is not installed correctly. Repeat this step, and see Pictures C and D (D is on next page) for
how the PowerArm will look when correctly installed.

Picture D

Horizontal head

of PowerArm

locked under tip

of V-ring.

Hook of

upper spring

(Top view)

3) Reinstall the original spring so that the PowerArm is held in place by the hook of the spring. See Pictures D and G (G is on next

page).

Note: The horizontal head of the PowerArm will be situated below the V-ring. The hook of the original spring will be situated
between the V-ring and the horizontal head of the PowerArm (see Pictures D and G).

PowerArm—when properly installed on
V-ring—is held in place by upper spring.

5

Assembly and Installation Instructions

C

A

Spring assembly

Picture F

C

Picture E

A

4) Connect a PowerSpring to the looped end of a PowerHook to create a “spring assembly.” Connect PowerHook to spring notch on

frame, as shown. Spring assembly will hang on outside of frame.

Picture G

Position 3

Position 2

PowerSpring shown
connected to Position

1 of PowerArm

5) Connect the opposite end of the PowerSpring to Position 1 on the PowerArm (Standard Setting). You now have one “PowerBounce

assembly” installed.

Note: For jumpers over 185 lbs or if a firmer feel is desired, connect the PowerSpring to Position 2 or Position 3 on the PowerArm
(see Picture G).

>> Repeat Steps 2-5 at every location that a PowerBounce Assembly is to be installed, according to which PowerPack you have, as
listed on page 4.

A

6

Assembly and Installation Instructions

V-ring

Original spring

C

(PowerHook)

B

(PowerArm)

A

(PowerSpring)

Cut-away side-view of trampoline

with PB Assembly installed

Your PowerBounce Set is now installed!

NOTE: If the PowerArm or the PowerSpring comes loose after jumping, the PowerArm has not been installed correctly. Repeat
Steps 2 and 3, and see Pictures C and D for how the PowerArm should look after it is properly installed.

7

&

Limited 5 Year Warranty

What is covered by this warranty? This warranty covers any defects in materials or workmanship on all of the components

of the JumpSport / AlleyOop Sports (collectively referred to here as “JumpSport”) PowerBounce PowerPack 20, PowerPack 32,
PowerPack 48, and PowerPack 64, and is extended exclusively to the original retail purchaser. (The PowerBounce PowerPacks
only consist of PowerSprings, PowerArms, and PowerHooks.)

How long does this coverage last? Warranty coverage for each component of the PowerBounce system begins from the

original date of purchase and only covers the specific PowerBounce system parts as follows:

 PowerSprings - five years
 PowerArms - five years
 PowerHooks - five years

What will JumpSport do? If you return the defective part to JumpSport as instructed below, JumpSport will either repair or

replace such part, at JumpSport’s discretion, and return it to you.

What is not covered by this warranty? This warranty does not cover expenses of on-site labor, shipping costs, travel,

assembly or disassembly, or other charges associated with the repair or replacement of covered components. This warranty
also does not cover any problem that is caused by abuse, misuse, commercial or public use, ordinary wear and tear,
weathering, acts of God (such as wind and lightning), failure to follow directions, improper installation, improper maintenance,
or any silk screened graphics. Rust is a natural occurrence with any outdoor steel product and is likewise not covered by this
warranty, to the extent that it does not affect the structural integrity of the part. (This warranty does not cover the JumpSport /
AlleyOop Sports trampolines or any related safety enclosure. See individual trampoline and safety enclosure warranties for
specific coverage details for those products.)

JUMPSPORT IS NOT RESPONSIBLE OR LIABLE FOR INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING
OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCT OR OTHER DAMAGES WITH
RESPECT TO ANY LOSS, INCLUDING BUT NOT LIMITED TO ECONOMIC LOSS, LOSS OF PROPERTY, LOSS OF REV­ENUE OR PROFITS, LOSS OF ENJOYMENT OR USE, COST OF REMOVAL, INSTALLATION OR OTHER CONSE­QUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CON­SEQUENTIAL DAMAGES. ACCORDINGLY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

THE WARRANTY EXTENDED HEREUNDER IS IN LIEU OF ALL OTHER WARRANTIES AND ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN ITS SCOPE AND DURATION TO
THE TERMS SET FORTH HEREIN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS. ACCORDINGLY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

How to get a defective part replaced:

1) Call the JumpSport Customer Service department at 408-213-2551 to obtain a Return Authorization number. All returns
must be pre-authorized.

2) Send the part(s) to the designated Service Center, along with a copy of your original sales receipt and a brief written
description of the problem, including how it occurred. You must pay freight and insurance to return the part to
JumpSport. At JumpSport’s sole discretion, we may ask you to send photographs in addition to or in lieu of returning the
part.

3) After inspecting the returned part(s), JumpSport will make a final determination whether the part is covered by this
warranty. We reserve the right to examine photographs or physical evidence concerning parts claimed to be defective prior
to making a final determination concerning the claim. A repaired or replacement part will be returned to you. (Shipping
charges may apply.) Please allow 3 to 4 weeks for delivery.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

8