JumpSport 120, 280, 480XT, 380, 480 Assembly & Installation Manual

1

JumpSport, Inc.
2055 South 7th Street, Suite A
San Jose, CA 95112 U.S.A.

408-213-2551

www.jumpsport.com

Retain address information for future use.

Alternate Assembly Instructions for

Safety Enclosures

Models 120, 280, 380, 480, and 480XT

Assembly, Installation, Care, Maintenance, and Use

Instructions

WARNING

Read these materials prior to assembling and

using this Trampoline Enclosure

DO NOT attempt or allow
somersaults. Landing on the
head or neck can cause serious
injury, paralysis or death, even
when landing in the middle of the
bed.

DO NOT allow more than one
person inside the trampoline
enclosure. Use by more than
one person at the same time
can result in serious injury.

Use trampoline only with mature, knowledgeable supervision.

DO NOT attempt to jump over
the barrier.

DO NOT intentionally rebound
off the barrier.

DO NOT hang from, kick, cut
or climb on the barrier.

The maximum user weight is:

Model 280: 200 pounds

Model 120 & 380: 230 pounds

Models 480 & 480XT: 295 pounds

P/N: INS-P-11722-01A

2

Copyright Notice

This material is protected by United States copyright laws and is proprietary to JumpSport, Inc. Disclosure, reproduction, translation,
modification, or use of this document by anyone other than authorized employees, authorized users, or licensees of JumpSport
without the prior written consent of JumpSport, Inc. is prohibited.

The information in this document is subject to change without notice. JumpSport, Inc. shall not be liable for any damages resulting
from technical errors or omissions, which may be present in this document, or from use of this document.

Copyright © 1997-2009, by JumpSport, Inc. All rights reserved.

Printed: 2009

Instruction Manual P/N: INS-P-11722-01A

JumpSport 12ft Safety Enclosure Model 120 P/N: SEJ-S-11338A
JumpSport 10ft—14ft Safety Enclosure Model 280 P/N: SEJ-S-11339A
JumpSport 10ft—14ft Safety Enclosure Model 380 P/N: SEJ-S-11340A
JumpSport 10ft—14ft Safety Enclosure Model 480 P/N: SEJ-S-11341A
JumpSport 14.1ft—16ft Safety Enclosure Model 480XT P/N: SEJ-S-11342A

Trademarks

JumpSport®, ProFlex™ Basketball Set, Game and Party Pak™, SureStep™ Trampoline Ladder, and BounceBoard Extreme™ are
trademarks of JumpSport, Inc.

All other brand or product names are trademarks or registered trademarks of their respective companies or organizations.

Patents

This product includes technology associated with one or more of the following U.S. Patents:

No. 6,053,845

No. 6,261,207

No. 6,840,891

No. 6,846,271

No. 7,060,001

Additional Patents Pending.

How to Contact Customer Support

Should you require customer service or technical support for your JumpSport Safety Enclosure, please contact JumpSport’s Customer
Service department at:

408-213-2551

8:00am—5:00pm Monday through Friday, Pacific Time

3

Contents

Chapter 1 Introduction 5

JumpSport ProFlex Basketball Set 6
Game and Party Pak 6

Chapter 2 Assembly and Installation Instructions 7

Preparation 7

Trampoline Placement 7
Tools 8
Parts List 8

Assembly 9
Type A Installation 15

Type B Installation 22
Final Steps 28

Disassembly 28

Please refer to the manual that came with your enclosure

for all other chapters.

4

(This page left intentionally blank.)

5

Introduction 1

Congratulations on purchasing a JumpSport Safety Enclosure! We sincerely believe that you have purchased the finest
safety enclosure on the market. It has been engineered with safety, durability, and performance in mind.

Safe use of a trampoline also requires adequate knowledge of technique, as well as what not to do. Please read this
manual thoroughly for key points of safety.

Trampolines, being rebounding devices, propel the performer to unaccustomed heights and into a variety of body
movements. Therefore, it is emphasized that all purchasers, and all persons using the trampoline, become familiar with
the rules for safe use. Misuse and abuse of this trampoline is dangerous, and can cause serious injuries. The purchaser/
user of this piece of equipment is assuming a degree of risk for which JumpSport cannot be responsible.

Read this information thoroughly before allowing the trampoline to be used. Keep this manual available for your
review, and for review by all potential users. If there are questions please call JumpSport for further explanation.

Caution

Many users of our trampolines are children, and therefore need close supervision and rules to follow while playing on
the trampoline. These rules must be enforced by whomever is responsible for the care of the children. It is strongly
recommended that the buyer of this product go over the rules and recommendations in the packet of information
supplied, including those in this manual. It is also strongly recommended that these rules and recommendations be
supplemented with those of your own, for example: the time that jumping is allowed, when neighbors can visit, and so
on. These rules and recommendations should be reviewed with anyone who is going to jump on the trampoline. If it is
possible, review these rules with the parents or guardians of any visitors who may be jumping on the trampoline. See
Safety Rules (under the Use Instructions section) for more information.

6

Don’t miss out on these fun accessories and more at

www.jumpsport.com !

Bring the party to your
trampoline! The Game & Party
Pak is a great way to take
turns and have fun
participating in games while
you are waiting.

Convince your parents that
games provide the “structure"
you need in your life, and that
the Game & Party Pak is just
the solution. Plus, you can tell
them the Party Pak does big
words like:

• Enhances Athletic Building
Blocks

• Develops Agility, Stamina,
Balance, Coordination

• Improves Spatial
Awareness

(They won’t be able to turn you
down!)

Set Includes:

• Illustrated book of 20
games

• 3 soft balls

• 4 shock cords

• 1 box of sidewalk chalk

• Hours of fun!

Let’s face it, kids have to look up
a lot: at parents, teachers, and
bigger brothers/sisters. With the

JumpSport ProFlex Basket­ball Set, look down for a

change!
Whether you are into practicing

your outside shot or improving
your up-close game, the Pro-
Flex Basketball Set is a fun
way to avoid homework. Heck,
athletic scholarships pay for
college too!

• Our most popular
accessory!

• Easily installed to your
safety enclosure

• Set includes basketball

JumpSport ProFlex Basketball Set

Introduction

Game & Party Pak

7

Assembly and Installation
Instructions 2

Preparation

Before you begin assembling your JumpSport Safety Enclosure, make sure your trampoline is in a proper location.

Trampoline Placement

Caution:

When deciding on where to place your trampoline, consider the following:

WARNING

Overhead Clearance Adequate overhead clearance is essential. A minimum of 24 feet from ground level
is recommended. Provide clearance for wires, tree limbs, and other possible hazards.

Lateral Clearance Lateral clearance is essential. Place the trampoline and trampoline enclosure away from
walls, structures, fences, and other play areas. Maintain a clear space on all sides of the
trampoline and trampoline enclosure.

Level Surface Place the trampoline and trampoline enclosure on a level surface before use.

Lighting Use the trampoline and trampoline enclosure in a well-lighted area. Artificial
illumination may be required for indoor or shady areas.

Security Secure the trampoline and trampoline enclosure against unauthorized and

unsupervised use.

Ground Clearance Remove any obstructions from beneath the trampoline and trampoline enclosure.

Note: The trampoline enclosure is only to be used as an enclosure for a trampoline of a size for which the enclosure
is designed.

Note: The owner and supervisors of the trampoline are responsible to make all users aware of practices specified in
the Use Instructions.

IMPORTANT: The best surface on which to place your trampoline is dirt or grass. However, if you plan to install the
trampoline on a very hard surface such as concrete or asphalt, a dense foam — similar to what can be found in
public playgrounds — should be installed under each leg. Contact JumpSport Customer Service if you have any
questions.

It is the responsibility of the purchaser to become familiar with all of the information in this booklet, to
convey the warnings to all users, and to enfo rce Jump Spo r t’ s rul es fo r s afe use .

This unit is not intended for commercial or public use and is therefore strictly prohibited.

The maximum user weight is: 200 pounds (Model 280), 230 poun ds (Models 120 & 380), or 295 pounds
(Models 480 & 480XT), or the specified user weight rating of your trampoline, whichever is lower.

8

Assembly and Installation Instructions

Tools

Installation of the safety enclosure requires a 10mm deep socket and ratchet, or a crescent/adjustable wrench. An 8 foot
A-Frame ladder will be useful for some steps (use care and follow procedures for use). Safety glasses and gloves are also
recommended for safety.

Parts List

Your JumpSport Safety Enclosure is shipped with the parts shown below. Some parts will be located in a smaller inner
box. If any parts are missing, immediately call JumpSport Customer Service at 408-213-2551.

Note: Do NOT discard the foam tubing (Reference #3 and #4); it is needed to make the pole assemblies. It is not
just packing material. Not all poles will have foam around them. And do NOT remove any caps from the ends of any
of the support poles.

Acorn nut

Ref. #7g

Nylock nut

Ref. #7f

Reference # Part # Description Quantity

1 POL-A-10238A Lower support pole, with snap-button 8
2 POL-P-10118A Upper support pole, notch at one end 8
3 FOA-P-10078A Long foam tubing (1 tube packed over 1 pole) 8
4 FOA-P-10103A Short foam tubing (2 tubes packed over 1 pole) 8
5 SLE-P-11467A Pole sleeve, blue vinyl 8

6 CAP-P-10075A Ball end cap 8
7a BOL-P-10120A M6 U-bolt 24
7b CLA-P-10105A Clamp 24
7c WAS-P-10106A Washer 48
7d NUT-P-10107A M6 Nylock nut 48
7e NUT-P-10621A M6 acorn nut, capped end 16

8 CAP-P-10123A U-bolt cap cover, black 8

9 CAB-P-10116A Cable tie 8

10

NET-P-11198A (120 net)
NET-P-11522A (280/380 net)
NET-P-11523A (480 net)
NET-P-10469A (480XT net)

Safety net 1

11 BUN-P-10126A 1ft bungee, loop at one end, hook at other end 8

12

STR-P-10115A
Model 280
All other models

10.5ft pole strap, loop at one end

(Depending on your trampoline and safety
enclosure, not all straps will be used.)

8

16

13 BUN-P-10125A

6ft bungee, loop at one end, hook at other end

(120, 380, 480, 480XT only)

8

9

The following pages contain diagrams, pictures, and written instructions for assembling your JumpSport Safety
Enclosure. The “Ref. #” mentioned in many steps is referring to the “Reference #” column of the parts list on the
previous pages.

Familiarize yourself with the Assembly and Installation Instructions before beginning installation.

For installation questions, please contact JumpSport’s Customer Service department at:

408-213-2551

8:00am—5:00pm Monday through Friday, Pacific Time

Assembly and Installation Instructions

Assembly

Note: We recommend at least 2 people participate in assembling the safety enclosure. Use page 8 to help with part
names and numbers.

1) Build all pole assemblies as shown. (Pole sleeve and foam will fit tightly up inside ball end cap.) See page 8 for detailed part

descriptions.

Lower pole (Ref. #1) Upper pole (Ref. #2)

Long foam tubing (Ref. #3) Short foam tubing (Ref. #4)

Pole sleeve (Ref. #5)

Ball end cap (Ref. #6)

CAUTION

Pinch point.

Pay careful attention to hand
position when connecting
tubes.

Top of pole sleeve

(narrow end)

Top of lower pole

(narrower end

with snap button)

Top of upper pole

(notched end)

10

Assembly and Installation Instructions

Pole 1

Pole 2

Note: If your trampoline has 6 sets of u-shaped legs instead of 4, use the above diagram for pole placement.

= u-shaped leg (6 total, with 12 vertical attachment points)

= safety enclosure pole (8 total)

11

Acorn nut
Ref. #7e

Assembly and Installation Instructions

2) Using the hardware provided, connect a pole to the outside of

each trampoline leg:

• If you have a JumpSport Trampoline, bottom of pole must

line up with red mark on vertical leg piece. This will ensure
that pole is at proper height. (If red marks are missing, see

below.)

• If you do not have red marks on your trampoline legs, the

safety enclosure pole should extend 73 inches (6 feet 1 inch)
above the jumping surface (mat), as shown above.

• Align notch in ball end cap with rail as shown above.

• Bottom U-bolt should be approximately 2 inches above

bottom of pole.

• Snugly tighten Nylock nuts.

• Hand-tighten acorn nuts.

3) Wrap cable tie around U-bolt cap cover and pole. Secure cable

tie to hold cap cover in place.

(Side
view)

U-bolt (Ref. #7a)

(Red mark

on leg)

Frame pad

Nylock nut

Ref. #7d

Clamp

Ref. #7b

U-bolt cap cover
Ref. #8

Washer
Ref. #7c

Nylock nut
Ref. #7d

Notch in ball end cap

should be aligned with rail,

as shown.

Cable tie

Ref. #9

Pole extends

73 inches

above mat

IMPORTANT: Be s ure nothing is
caught between pole and leg
(including pole sleeve, foam
tubing, frame pad, etc.) before
tightening U-bolts.

12

5) Top strap of net is slightly wider than bottom strap. Wider

strap must be at top of net. Place looped end of top strap of net
around ball end cap at pole 1. Pole 1 must be at a right vertical leg
piece.

Pole 1

Pole 2

Pole 3

Pole 4

Pole 5

Pole 6

Pole 7

Pole 8

Start

(Top view.

Legs shown

with dotted

lines.)

6) Hang net clockwise along the inside of pole 2. Top strap and 1

mesh of netting must rest in groove on top of ball end cap. Top
strap should hang slightly curved between poles 1 and 2.

4) Familiarize yourself with the net. The net has a wider strap at the top of the net. There are red marks on the top and bottom straps

of net to help with installation. However, the red marks will NOT line up with the poles if you do not have a 14ft or 16ft trampoline. If
you have a 480XT net, there will be no red marks on the straps at all.

IMPORTANT: There are knots in all 4 corners of the net. These knots should not be removed f or any reason, and are require d in
order for the net to install properly.

Wider top

strap

Ball end cap at Pole 1

Wider top

strap

Net

Ref. #10

End
with
loop

Bottom

strap

written and slaved over by
Andy Graser for many long
hours. speci al thanks to Jon
Greiner and April Smith for
their help and contributions.

Ball end cap

Ref. #6

Knot

Pole 1

(Net shown hung

on poles 1 - 3)

(Top view)

(View from outside of net)

Pole 4

Pole 6

Assembly and Installation Instructions

13

Assembly and Installation Instructions

10) At starting edge of net (where you first hung the net on pole

1), find the bottom corner. Pull bottom corner toward pole 1.
Wrap bottom strap of net around pole 1, below rail of trampoline,
as shown. Secure with a strong knot.

Note: When you are done, the strap should be wrapped an d tied
so that there is no excess hanging.

8) Continue back to pole 1. Hang net around outside of pole 1,

with top strap and 1 mesh of netting resting in groove on top of
ball end cap. Then pull net to pole 2. Wrap net around inside of
pole 2, around neck of ball end cap, and double it back on itself
toward pole 1. Then net will be able to pull back to pole 1 or even
pole 8.

Note: Bottom of net in some locations may not be touching
trampoline at this time. This is normal.

7) Now hang net clockwise around outside of all remaining

poles. Top strap and 1 mesh of netting must rest in groove on top
of ball end cap. Top strap should hang slightly curved between
poles.

Pole 1 or 8

Bottom corner of

inside panel of net

9) Feed top strap through top of net near pole 1 (or pole 8 if net

itself can be pulled past pole 1). Wrap top strap around ball end
cap to secure it. Then tie a double knot in the strap. Loosely wrap
excess strap around pole 1 (or pole 8), and tie off loose end as low
on the pole as you can.

Pole 1

(Net shown hung

on poles 1 - 4)

(Top view)

(View from outside of net)

Pole 4

Pole 6

Pole 1 or 8

Pole 1

Pole 2

Pole 1 Pole 2

14

11) If your trampoline frame pad has button bungees going through the large pad section of pad—as shown above—continue to the

next step for Type A Installation.

If your trampoline frame pad does NOT have button bungees going through middle of pad, skip to page 21 for Type B Installation.

Button bungee

Type A Installation

Assembly and Installation Instructions

15

Type A Installation

Note: Use page 8 to help with part names and numbers. All parts may not be used for this installation.

Assembly and Installation Instructions–Type A Installation

13) At outer panel of net, pull the bottom corner strap straight across to same pole that you tied top of net to in Step 9. Wrap bottom

strap around this pole and secure with a strong knot.

Note: When you are done, the strap should be wrapped and tied so that there is no excess hanging.

12) Find pole that you tied off to top of net in Step 9. Lift frame pad between that pole and pole to left of it. Tuck pad skirt up

underneath pad, so skirt is wedged between bottom of pad and rail of trampoline.

Note: If you attached your net to pole 8 in Step 9, then you also need to tuck pad skirt up underneath pad between poles 1 and 2.

Note: All the pictures in this

manual show the net tied off to
pole 1, for illustrative purposes.

However, your net may be tied off

to pole 8 instead of pole 1.

Pole 1 Pole 2

16

15) Starting at pole 2 and working clockwise around trampoline, pull bottom of net down pole, so that bottom strap of net is

positioned below bottom of pole foam. Wrap a 1ft bungee around bottom strap of net, then around trampoline leg, and connect ends
of bungee together under trampoline frame. Ignore red marks on bottom strap if there are any.

>> Repeat at all other poles, continuing to work clockwise around trampoline.

1ft
bungee

Ref. #11

14) The net between poles 1 and 3 should now look like the above pictures (but the pictures will only match if your net tied off to

pole 1 instead of pole 8). For a top down view, see page 27.

Bottom

strap of net

Assembly and Installation Instructions–Type A Installation

Pole 1 Pole 2

Pole 2 Pole 3

17

16) Find the 2 button bungees on top of frame pad between poles 1 and 2. Secure bottom strap of inner panel of net at each button

bungee with a square knot, as shown.

A

B

C

D

Square knot

E

Button bungee

Assembly and Installation Instructions–Type A Installation

(Outer panels of net

not shown for clarity.)

Pole 1 Pole 2

18

17) At pole that you tied off top of net to in Step 9, wrap a 10.5ft pole strap around the vertical leg piece as shown. Strap must wrap

around pole and leg below rail, and behind 1ft bungee. Then pull non-looped end of pole strap all the way through looped end.

10.5ft pole strap

Ref. #12

1ft
bungee

IMPORTANT: Flip

warning placard up out of
the way when performing
this step.

18) Wrap 10.5ft pole strap around rail and through bottom strap of both outer panels of net. Then continue wrapping 10.5ft pole

strap around rail toward next pole to the left. Pole strap should wrap once around rail between each spring before getting to next
pole. Secure at that pole with a strong knot.

Note: When you are done, the strap should be wrapped and tied so that there is no excess hanging.

Assembly and Installation Instructions–Type A Installation

IMPORTANT: Pole strap
must not be pinched by
springs.

19

19) Secure bottom strap of net to each button bungee sticking out of top of frame pad. Do not wrap pole strap around net mesh, only

around bottom strap of net. Tie bungee to bottom strap of net as shown in Step 16.

(View from inside trampoline)

(View from outside trampoline)

w

r

i

t

t

e

n

a

n

d

s

l

a

v

e

d

o

v

e

r

b

y

A

n

d

y

G

r

a

s

e

r

f

o

r

m

a

n

y

l

o

n

g

h

o

u

r

s

.

s

p

e

c

i

a

l

t

h

a

n

k

s

t

o

J

o

n

G

r

e

i

n

e

r

a

n

d

A

p

r

i

l

S

m

i

t

h

f

o

r

t

h

e

i

r

h

e

l

p

a

n

d

c

o

n

t

r

i

b

u

t

i

o

n

s

.

Warning placar d

20) Be sure the warning placard attached to the bottom strap of net (at the doorway) is clearly visible at all times.

If you have a Model 280 Safety Enclosure, installation is now complete! For all other enclosure models,
continue to the next step.

Assembly and Installation Instructions–Type A Installation

20

22) Weave 6ft bungee in and out of approximately every 3

squares of net, on outside of pole. Bungee will weave on inside of
net for 3 squares, outside of net for 3 squares, inside of net for 3
squares, etc.

21) Steps 21— 26 are for Mo dels 120, 380, 480, and

480XT only. If you have a 280, installation is now
complete:

At top of net, wrap a 6ft bungee around ball end cap. Then pull
hooked end of bungee all the way through looped end of bungee
so that bungee is snug.

(View from outside of net)

(View from outside of net)

6ft bungee

Ref. #13

24) Place loop of 10.5ft pole strap in slot of ball end cap. Pole

strap should hang on inside of net.

23) Wrap 6ft bungee around vertical leg piece, under trampoline

rail. Secure hooked end of bungee to bungee itself, between pole
and rail, as shown.

>> Repeat Steps 21—23 at all remaining poles.

(View from outside of net)

10.5ft pole
strap

Ref. #12

6ft bungee

(Front-view from

outside of net)

(Side-view)

Assembly and Installation Instructions (Models 120, 380, 480, & 480XT only)–
Type A Installation

21

Assembly and Installation Instructions (Models 120, 380, 480, & 480XT only)–

Type A Installation

25) Wrap 10.5ft pole strap around pole and around the 6ft

bungee that is on the inside of the net. Do not wrap pole strap around
net mesh, only around 6ft bungee on the inside sections of net. This
will create approximately 5—8 wraps.

26) Tie end of 10.5ft pole strap off with a firm knot at bottom of

pole, just below rail.

Note: When you are done, the strap should be wrapped an d tied
so that there is no excess hanging.

>> Repeat Steps 24—26 at all remaining poles, EXCEPT pole 2.

(Picture not

to scale)

(Side
view)

10.5ft pole strap

Your safety enclosure is now complete!

22

Type B Installation

Note: Use page 8 to help with part names and numbers. All parts may not be used for this installation.

12) Lift frame pad between poles 1 and 2. Tuck pad skirt up underneath pad, so skirt is wedged between bottom of pad and rail of

trampoline.

>> Repeat this step all the way around the trampoline so that the pad skirt is tucked underneath the pad between each set of poles.

Assembly and Installation Instructions–Type B Installation

13) At outer panel of net, pull the bottom corner strap straight across to same pole that you tied top of net to in Step 9. Wrap bottom

strap around this pole and secure with a strong knot.

Note: When you are done, the strap should be wrapped and tied so that there is no excess hanging.

Note: All the pictures in this

manual show the net tied off to
pole 1, for illustrative purposes.

However, your net may be tied off

to pole 8 instead of pole 1.

Pole 1 Pole 2

23

1ft
bungee

Ref. #11

14) The net between poles 1 and 3 should now look like the above pictures (but the pictures will only match if your net tied off to

pole 1 instead of pole 8). For a top down view, see page 27.

Bottom

strap of net

Assembly and Installation Instructions–Type B Installation

Pole 1 Pole 2

Pole 2 Pole 3

15) Starting at pole 2 and working clockwise around trampoline, pull bottom of net down pole, so that bottom strap of net is

positioned below bottom of pole foam. Wrap a 1ft bungee around bottom strap of net, then around trampoline leg, and connect ends
of bungee together under trampoline frame. Ignore red marks on bottom strap if there are any.

>> Repeat at all other poles, continuing to work clockwise around trampoline.

24

16) At pole that you tied off top of net to in Step 9, wrap a 10.5ft pole strap around the vertical leg piece as shown. Strap must wrap

around pole and leg below rail, and behind 1ft bungee. Then pull non-looped end of pole strap all the way through looped end.

10.5ft pole strap

Ref. #12

1ft
bungee

17) Wrap 10.5ft pole strap around rail and through bottom strap of both outer panels of net. Then continue wrapping 10.5ft pole

strap around rail toward next pole to the left. Pole strap should wrap once around rail between each spring before getting to next
pole. Secure at that pole with a strong knot.

Note: When you are done, the strap should be wrapped and tied so that there is no excess hanging.

>> Repeat steps 16 and 17 at all other poles around trampoline, EXCEPT between poles 2 and 3. See next step for how to tie pole strap
between poles 2 and 3. There may not be 2 outer panels of net, or an inner panel of net, all the way around the trampoline. This is
normal.

IMPORTANT: Flip
warning placard up out of
the way when performing
this step.

Assembly and Installation Instructions–Type B Installation

IMPORTANT: Pole strap
must not be pinched by
springs.

25

19) Be sure the warning placard attached to the bottom strap of net (at the doorway) is clearly visible at all times.

If you have a Model 280 Safety Enclosure, installation is now complete! For all other enclosure models,
continue to the next step.

Assembly and Installation Instructions–Type B Installation

18) Between poles 2 and 3, secure only the left half of bottom strap of net to trampoline rail. Pole strap will still wrap once between

each spring all the way across the rail, but net itself will only be secured to rail on left half of net, as shown above.

Securing the net this way allows enough room for someone to enter the trampoline just to the left of pole 2.

Pole 2 Pole 3

Left half of

bottom strap of

net

w

r

i

t

t

e

n

a

n

d

s

l

a

v

e

d

o

v

e

r

b

y

A

n

d

y

G

r

a

s

e

r

f

o

r

m

a

n

y

l

o

n

g

h

o

u

r

s

.

s

p

e

c

i

a

l

t

h

a

n

k

s

t

o

J

o

n

G

r

e

i

n

e

r

a

n

d

A

p

r

i

l

S

m

i

t

h

f

o

r

t

h

e

i

r

h

e

l

p

a

n

d

c

o

n

t

r

i

b

u

t

i

o

n

s

.

Warning placar d

26

21) Weave 6ft bungee in and out of approximately every 3

squares of net, on outside of pole. Bungee will weave on inside of
net for 3 squares, outside of net for 3 squares, inside of net for 3
squares, etc.

20) Steps 20— 25 are for Mo dels 120, 380, 480, and

480XT only. If you have a 280, installation is now
complete:

At top of net, wrap a 6ft bungee around ball end cap. Then pull
hooked end of bungee all the way through looped end of bungee
so that bungee is snug.

(View from outside of net)

(View from outside of net)

6ft bungee

Ref. #13

23) Place loop of 10.5ft pole strap in slot of ball end cap. Pole

strap should hang on inside of net.

22) Wrap 6ft bungee around vertical leg piece, under trampoline

rail. Secure hooked end of bungee to bungee itself, between pole
and rail, as shown.

>> Repeat Steps 20—22 at all remaining poles.

(View from outside of net)

10.5ft pole
strap

Ref. #12

6ft bungee

(Front-view from

outside of net)

(Side-view)

Assembly and Installation Instructions (Models 120, 380, 480, & 480XT only)–
Type B Installation

27

Your safety enclosure is now complete!

Assembly and Installation Instructions (Models 120, 380, 480, & 480XT only)–

Type B Installation

24) Wrap 10.5ft pole strap around pole and around the 6ft

bungee that is on the inside of the net. Do not wrap pole strap around
net mesh, only around 6ft bungee on the inside sections of net. This
will create approximately 5—8 wraps.

25) Tie end of 10.5ft pole strap off with a firm knot at bottom of

pole, just below rail.

Note: When you are done, the strap should be wrapped an d tied
so that there is no excess hanging.

>> Repeat Steps 23—25 at all remaining poles, EXCEPT pole 2.

(Picture not

to scale)

(Side
view)

10.5ft pole strap

28

Final Steps

Assembly is now complete! Make sure all parts are securely assembled. Before using your JumpSport Safety Enclosure,
familiarize yourself and all users with the Care and Maintenance Instructions, Warning Information, and Use Instructions
included in this manual. See Diagram 1, below, to see how to properly enter the safety enclosure.

To register your JumpSport Safety Enclosure, visit our webpage at www.jumpsport.com and click on the Product
Registration link.

Note: The net may need periodic adjusting. Check the knots and straps regularly. If the net sags due to extended
use, we recommend going back and repeating Step 5 all the way through to the end of the manual.

WARNING: Trampoline use is not recommended without the frame pad installed. The frame pad is

designed to reduce the possibility of injury by protecting the user from coming into contact with the frame
and springs of the trampoline. It is very important that you properly attach the frame pad securely to the
frame and in the correct position prior to using the trampoline.

Disassembly

To disassemble your JumpSport Safety Enclosure, follow the assembly steps in reverse order.

*For more information about the SureStep Trampoline Ladder,

the ProFlex Basketball Set, the BounceBoard Extreme,

and other great trampoline accessories,

visit our website at www.jumpsport.com

Pole 1

Pole 2

Enter through here.

Diagram 1

(Top view)

To enter your

JumpSport Safety

Enclosure, step up onto

the frame between

poles 2 and 3.

Then, move

to the right, passing

between the inside and

outside panels

of net.

A SureStep

Trampoline Ladder*

makes entering the

trampoline easy.

Assembly and Installation Instructions

Pole 3