Jump-N-Carry
®
Models 300, 400, 660, 950, 4000 & 12/24
Charge the Jump-N-Carry®for 24 hours upon opening the box.
The unit must be fully charged before use or long-term storage.
Thank you for purchasing the best jump-starter unit on the market. Your unit has
been equipped with special features to make the jump-starting process easier.
To ensure trouble-free use, please remember to recharge the unit for 24 hours
at least once every 3 months during the winter, and monthly during the summer.
842-355-001
This unit contains a sealed, non-spillable lead-acid
battery, which must be recycled. Consult your local
government concerning regulations for proper disposal.
See Battery Replacement section.
Pb
2
1. Read these instructions completely before using the product and save
them for future reference.
2. WARNING: POSSIBLE EXPLOSION HAZARD — WORKING AROUND LEAD-ACID
BATTERIES MAY BE DANGEROUS. LEAD ACID BATTERIES RELEASE
EXPLOSIVE GASES DURING NORMAL OPERATION, CHARGING, AND
JUMP-STARTING. CAREFULLY READ AND FOLLOW THESE INSTRUCTIONS
FOR SAFE USE. ALWAYS FOLLOW THE SPECIFIC INSTRUCTIONS IN THIS
MANUAL AND ON THE JUMP-N-CARRY®EACH TIME YOU JUMP-START USING
THE JUMP-N-CARRY®.
3. Before using the Jump-N-Carry
®
to jump-start a car, truck, boat or to power
any equipment, read these instructions and the instruction manual/safety information
provided by the car, truck, boat or equipment manufacturer. Following all manufacturers’
instructions and safety procedures will reduce the risk of accident.
4. General precautions for use:
• Always wear eye protection and appropriate protective clothing when working near
lead-acid batteries. Do not touch eyes while working on or around lead-acid batteries.
• Never work alone with electrical equipment. Make sure that someone is around to
give assistance if you need help.
• Always store, use, and charge the Jump-N-Carry®in an area where children
cannot get to the unit.
• The clamps of the Jump-N-Carry®portable jump-start system may cause
sparks if touched together. Always keep the clamps secured around Clamp Lock
arms to prevent sparking.
• The charger uses household 115 volt electrical supply, which if misused, may cause
injury or fire.
• All lead-acid batteries (car, truck, and boat) produce hydrogen gas which may violently explode in the presence of fire or sparks. Do not smoke, use matches or a cigarette lighter while near batteries. Do not handle the battery while wearing vinyl
clothing because static electricity sparks are generated when vinyl clothing is
rubbed.
• Use the Jump-N-Carry
®
to charge/jump-start lead-acid batteries only. Do not use the
unit to recharge dry cell batteries.
•Remove jewelry such as rings, bracelets, necklaces and watches when
working around a battery. A lead acid battery can produce a short circuit current,
which can melt metals and result in a severe burn.
• Do not drop tools or other metal objects on or near the battery as a spark may result,
igniting explosive gases.
• Do not jump-start or attempt to recharge a frozen battery.
WARNING: While the battery in the Jump-N-Carry®is a sealed unit with no free liquid acid,
batteries being jump-started with the Jump-N-Carry®unit likely contain liquid acids which
are hazardous if spilled.
Safety Information
3
WARNING: Failure to follow instructions may cause damage or explosion, always shield
eyes. Read this entire instruction manual before use.
1) Use in a well ventilated area. Shield eyes with safety glasses or goggles.
2) Turn off the ignition before making cable connections.
3) Do not touch the RED POS (+) clamp to the BLACK NEG (–) clamp.
4) First connect the RED POS (+) clamp to the POS (+) battery terminal, then
connect the BLACK NEG (–) clamp to the engine ground, or a non-moving metal
engine part. Stay clear of batteries while jump starting.
NOTE: A good, solid and clean connection is essential for a successful jump start
(see Performance and Temperature section).
5) After starting, disconnect the BLACK NEG (–) clamp first, then the RED POS (+) clamp.
6) Always return the jumper cables to the cable holders after use.
7) After use, recharge the Jump-N-Carry
®
(see Recharging Jump-N-Carry® section).
When jump-starting, do not use the unit for more than 6 seconds without a 3 minute rest
period between use. See the warranty for important details.
To ensure trouble-free use, please remember to recharge the unit for 24 hours at least
once every 3 months during the winter, and monthly during the summer (see Recharging
Jump-N-Carry
®
section).
WARNING: Failure to follow instructions may cause damage or explosion, always
shield eyes. Read entire instruction manual before use.
WARNING: Prior to jump-starting a vehicle, visually confirm that the unit is in the
same voltage mode (12 volt or 24 volt) as the vehicle to be jump-started. Improper
voltage selection may cause damage or explosion.
1) Use in a well ventilated area. Shield eyes with safety glasses or goggles.
2) Plug the voltage selector cable into the proper socket for:
12 volt charging system vehicles in the 12 volt Mode
24 volt charging system vehicles in the 24 volt Mode
3) Turn ignition off before making cable connections.
4) During nighttime use turn the emergency light on to identify the positive and negative battery terminals.
5) Do not touch the RED POS (+) clamp to the BLACK NEG (–) clamp.
6) First connect the RED POS (+) clamp to the POS (+) battery terminal, then
connect the BLACK NEG (–) clamp to the engine ground, or a non-moving metal
engine part. Stay clear of batteries while jump starting.
NOTE: A good, solid and clean connection is essential for a successful jump start
(see Performance and Temperature section).
7) After starting, disconnect the BLACK NEG (–) clamp first, then the RED POS (+)
clamp.
8) Always return the jumper cables to the cable holders after use.
9) After use, recharge the Jump-N-Carry
®
(see Recharging Jump-N-Carry® section).
When jump-starting, do not use the unit for more than 6 seconds without a 3 minute rest
period between use. See the warranty for important details.
To ensure trouble-free use, please remember to recharge the unit for 24 hours at least
once every 3 months during the winter, and monthly during the summer (see Recharging
Jump-N-Carry
®
section).
Jump-Starting Instructions:
Models 300, 400, 660, 950 & 4000 Only
Jump-Starting Instructions: Model 12/24 Only
4
Performance of your Jump-N-Carry®will depend upon several factors:
•Agood, solid connection between the Jump-N-Carry
®
clamps and the battery
and ground connections are a must. Moving the jumper cable clamps back and
forth while clamping will help create a better connection.
• Clean connections between your vehicle or equipment battery and its terminals
are very important. For an optimal connection, corrosion (soft grayish-white
build-up) upon battery terminals must be removed. With the ignition turned off,
disconnect the battery cables and clean the terminals and battery posts with a
baking soda solution.
• All batteries are affected by temperature changes, and the Jump-N-Carry®’s
small, lightweight battery is more sensitive to storage temperature than a standard automotive battery. Temperatures above 20º C will improve amperage output, while temperatures below 20º C decrease amperage output. The ideal storage environment for emergency use is at room temperature.
LED Indicators – MODEL 300 ONLY
To check the battery state of charge, press the red status button.
•AGood Green LED indicator only means the unit is ready to go.
•AGood Green LED and Recharge Red LED indicates the unit is low.
•ARecharge Red LED indicates the unit should be recharged before use.
•ACharging Red LED indicates the unit is charging and the AC charger
is working.
Battery Status Gauge – MODELS 400, 660, 950 & 4000
Press the red push-button to momentarily turn the gauge on.
• The Green shaded indicator bar indicates the unit is capable of jump-starting.
• The Yellow shaded indicator bar indicates the unit needs to be recharged.
• The Red shaded indicator bar indicates the unit must be recharged
before use.
Battery Status Gauge – MODEL 12/24
Press the red push-button to momentarily turn the gauge on. The gauge is an approximate
indicator of the battery's state of charge. When fully charged, the gauge should read 13 volts
or more when the unit is in the 12-volt mode, and 26 volts or more in the 24-volt mode.
12 Volt DC Accessory Outlet – MODELS 400, 660, 950, 4000 & 12/24 ONLY
Jump-N-Carry
®
is equipped with a standard 12 volt DC receptacle. Plug any accessory
up to 12 Amps into the socket and Jump-N-Carry®will provide power. If the amperage rating is exceeded, a built-in auto-reset circuit breaker automatically shuts power off until the
accessory, or overload source, is removed. Under extreme power usage, recharge the unit
for 36-48 hours.
Battery Status Panel
Performance and Temperature
12 Volt DC Power
5
RECHARGING USING AC POWER
Jump-N-Carry®300 Only:
The Jump-N-Carry®300 comes with a separate wall-mount charger.
1) Plug the charger cord into the recharge jack on the front of the unit, then plug into
a 120 VAC outlet.
2) The red Charging LED will illuminate while the charger is plugged into AC power to
indicate the unit is charging.
Jump-N-Carry
®
400, 660 & 4000 Only:
The Jump-N-Carry
®
400, 660 & 4000 require a household extension cord (not included).
1) Plug the female end of the extension cord into the charger plug on the front of the
unit. The charger plug has 2 blades and resembles a standard household plug that
would fit into a 120 VAC wall receptacle.
2) Plug the male end of the extension cord into a 120 VAC outlet.
NOTE: We do not recommend charging Jump-N-Carry
®
models 300, 400, 660, 950 or
4000 for more than 24 hours under normal usage. However, under extreme usage or high
discharge situations, recharge the unit for 36-48 hours.
Jump-N-Carry®950 and 12/24 Only:
The Jump-N-Carry
®
950 and 12/24 unit is equipped with a special automatic battery
charger that can be continually plugged into the unit and AC power. The automatic battery
charger is mounted under the front access plate.
1) Plug the end of the charging cord (part # 310241, included) into the charger receptacle on the front of the unit.
2) Plug the male end of the charging cord into any 120 VAC outlet.
Charge the unit for the recommended amount of time for your unit, as indicated on the chart
below. Once the time has expired, check the battery charging status (see Battery Status
Panel section on page 4) to ensure charging is complete.
Recharging Jump-N-Carry
®
MODEL
300
400, 660 &
4000
950 & 12/24
AFTER A SINGLE
JUMP-START
1 hour
1 hour
AFTER MULTIPLE
JUMP-STARTS
12 hours or overnight
12 hours or overnight
AFTER USING AS
PORTABLE POWER
24-36 hours
24-36 hours
These units are equipped with an automatic charger. Keep the unit
plugged in when not in use.
RECHARGING USING 12 VOLT POWER (requires optional accessory)
Jump-N-Carry®(models 400, 660, 950, 4000 and 12/24 only) may be recharged by
using an optional accessory cord with two male ends (see Optional Accessories section).
Plug one end into the Jump-N-Carry®’s 12V outlet and the other end into the vehicle’s
12V power port socket. The vehicle must be running to charge with this method.
NOTE: To recharge both batteries on the Jump-N-Carry®12/24, the 12 volt connector
must be plugged into the 12 volt side.
Suggested recharge times when using 12 volt power are:
• 20 minutes when the unit is used for jump-starting.
•2 hours when the unit is used for portable power.
•5 hours under very high discharge conditions.
SUGGESTED RECHARGE TIMES
6
Jump-N-Carry®may be stored virtually anywhere, and in any position. However, take pre-
cautions to ensure that the positive and negative clamps do not come into contact with each
other or a common metal surface. We recommend storing the Jump-N-Carry®in the box in
which it was received.
This unit contains a sealed non-spillable lead acid battery. The battery must be recycled.
Store in a cool, dry area.
The Jump-N-Carry®battery may be removed by unscrewing the perimeter screws on the
back cover. Disconnect the wires from the battery terminals. Note the position of the battery
and wire locations.
•2 wire connections go to each terminal.
• The small wires are color coded red for positive and black for negative.
• The large cable is identified by the color of the clamp attached to the cable, red is positive and black is negative.
Caution: It is possible the cables could become crossed inside of the case when the
battery is removed. The cables always travel straight to the battery terminals and should
never cross each other.
• All red wires (red clamp) attach to the positive side of the battery. All black wires (black
clamp) attach to the negative side of the battery.
•To connect a new battery, slide the battery fully into the case. Note the color of the wires
and match the color to the battery terminals.
• Replace the 6 or 8 perimeter screws on the back cover.
• Charge the new battery for 12 hours before use or storage.
(FOR MODELS 400, 660, 950, 4000, & 12/24 ONLY)
Though your new Jump-N-Carry®can already power almost any 12 volt DC accessory you
use in your car, RV or boat, shown below are two optional accessories that expand the
versatility of your Jump-N-Carry®.
AC POWER INVERTER: Household power from your portable jump-starter
Use the portable power outlet for power outages, fishing and camping trips, extended running time for camcorders, computers, and more. With the optional AC Power Inverter, the
uses of Jump-N-Carry®are unlimited! The inverter uses the DC battery power of your jump
starter to make 110/120 V AC power, and is equipped with standard household receptacle
outlets.
MALE-MALE POWER CORD
Allows the unit to be recharged from a vehicle’s 12 volt power port.
DC TO AC INVERTER
Optional Male-Male
Cord allows unit to be
recharged from vehicle
Optional AC
Power Inverter
from standard
household outlets
Storage
Battery Replacement
Optional Accessories
7
Q. What should I do if the Jump-N-Carry®will not hold a charge?
A. Load test the battery. Charge battery 24 hours before load testing. Connect a load tester
(available at your local auto parts store) to the Jump-N-Carry®clamps to check battery
amperage. Depending on the model of load tester your load testing procedure may vary.
A generic load test would bring the voltage down to 9.0 volts and result in an amp reading of 70 amps for 6 seconds. Repeat this load test every 10 minutes for a total of three
tests. If the amperage has dropped below 50 amps on the last test, suspect a bad or
weak battery.
Q. What is the ideal use for the Jump-N-Carry®?
A. The Jump-N-Carry®performs strongly when a vehicle’s battery needs an extra boost
because a light or radio was left on, or when a vehicle has been sitting for a long period
of time. The Jump-N-Carry®will start vehicles without any other batteries present but
the primary use is for an extra boost.
Q. Will the Jump-N-Carry®start every vehicle?
A. No. In addition to a dead battery, a car may have other mechanical problems that would
prevent the Jump-N-Carry®from starting the vehicle.
Q. How often should I recharge the Jump-N-Carry®?
A. To maximize battery life, charging after use is recommended. The Jump-N-Carry
®
should not be left in a discharged state. The battery in the Jump-N-Carry®has no memory problems and should not be treated as a rechargeable tool (cordless drills, camcorders, etc.).
Q. How many jump-starts can I get from the Jump-N-Carry®before recharging?
A. A large number of factors affect this answer including the following: the length of time for
each jump-start, the charge level of the original battery, the length of time between
jump-starts, the temperature of the vehicles being jump-started (winter cold makes for
difficult starting), the size of the engines (4-cycl, 6-cycl, 8-cycl, etc.), the mechanical
condition of the engine and starter, and more. These factors must all be weighed on an
individual basis before an accurate answer can be given. It’s feasible to get 10-30 starts
(individual’s results will differ) from a single charge, but this violates the rule of immediate charging after use.
Q. After jump-starting can I leave the unit hooked to the battery to recharge Jump-N-
Carry®while the engine is running?
A. NO. Attempting to recharge the Jump-N-Carry®by this method is not
recommended. Vehicle alternators output anywhere from 25-125 amps from the alternator. This charging rate greatly exceeds the recommended recharging rate for Jump-N-
Carry®. Charging by this method will result in overcharging the Jump-N-Carry®battery,
and may void the battery warranty.
Q. What accessories can be used in the optional 12 volt outlet?
A. Any accessory up to 12 amps can be powered by the Jump-N-Carry®. This unit is
equipped with an automatic reset circuit breaker should the current exceed 12 amps. At
the same time this limits any recharge current through the 12-volt outlet to 12 amps.
One can power almost any 12-volt tool or accessory (examples: torque wrenches, fans,
radios, cellular phones, navigation equipment, depth-finders, camcorders, emergency
power, trolling motors, coolers, small refrigerators, etc.).
Questions, Answers and
Troubleshooting
8
Clore Automotive warrants your Jump-N-Carry®to be free from defects in material
and workmanship, excepting abuse or misuse, for a period of 1 year from the date of sale to
the original user or consumer purchaser. If your Jump-N-Carry® malfunctions or fails within
the first 30 days of the warranty period we will replace it with a new unit. If your unit, excluding battery(s), malfunctions or fails within the 31–365 day warranty period because of a
defect in material or workmanship we will repair it without charge.
The battery, excluding units with swollen batteries or melted battery terminals, is prorated
monthly from the 31–365 day from the date of purchase at the full retail battery price set by
the manufacturer for all Jump-N-Carry® models.
This warranty excludes and does not include malfunctions or failure of your
Jump-N-Carry® which were caused by repairs made by an unauthorized person, mishan-
dling, modifications, normal wear, unreasonable use or damage to the
Jump-N-Carry®.
This warranty is in lieu of all other express warranties. The duration of any implied warranty,
including but not limited to any implied warranty of merchantability or fitness for a particular
purpose, made in respect to your Jump-N-Carry® is limited to the period of the express warranty set forth above.
In no event shall Clore Automotive be liable for consequential or incidental damages. Some
states do not allow limitations on the length of the implied warranty or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
Technical Service will quickly diagnose a problem with your Jump-N-Carry®. To obtain the
fastest and most efficient repair of your unit perform the following steps:
1. If the unit will not jump-start, recharge the unit for 24 hours.
2. If a part is broken or needs replacement call Technical Service for express part delivery.
3. If none of these answers solve your problem call (800) 328-2921.
Do not return your unit to the place of purchase. All inquiries about repairs and warranty
issues must be made directly with the factory. Return your product, with battery and proof of
purchase to the factory address listed below. You will be responsible for all insurance and
freight or other transportation charges to the factory or point of repair. We will return your
unit freight prepaid if repair is covered under warranty. When sending your Jump-N-Carry
®
to the factory, make sure the unit is securely packed, as we are not responsible for any
damage incurred to the unit in transit.
Technical Service Call (800) 328-2921
CLORE AUTOMOTIVE
copyright 8/01/00, revised 12/17/03
Jump-N-Carry
®
Warranty Service Department
8600 NE Underground Drive
Pillar 248
Kansas City, MO 64161
Jump-N-Carry® Limited Warranty
For Warranty or Service
Loading...