12ft (3.66m) Jumpking Classic Premium
User Guide
WARNING: Read these assembly instructions carefully
before attempting to assemble or use this product. Keep
this user guide in a safe place for future reference.
Got a Problem building your trampoline?
Call us on 0344 800 4060 and we can help
Patent no: DE602006006495D1, EP1721640B1 and US7628731
Made In China
IMPORTANT INFORMATION
2
. WARNING! ADULT SUPERVISION & GUIDANCE REQUIRED AT ALL TIMES.
. Recommended age 6+ years.
. No somersaults or flips - can cause serious injury.
WARNINGS!
. Only for domestic use.
. Maximum user weight limit 115 kg.
. Not suitable for children under 36 months - small parts, choking hazard.
. Outdoor use only.
. The trampoline should be assembled by an adult in accordance with assembly instructions
. Only one user. Collision hazard.
. Always close the net opening before jumping.
. Remove footwear before jumping on the tramp
. Do not use the mat / jumping bed when it is wet.
. Empty pockets and hands before jumping.
. Always jump in the middle off the mat / jumping bed.
. Do not eat whilst jumping.
. Do not exit by a jump.
. Limit the time of continuous usage (make regular stops).
. Do not use in strong wind conditions and sec
. The net should be changed every 1 year.
ure the trampoline.
ADVISORY
.
. The following product dimension relate to this 12ft round trampoline:
- Height from ground to top rail: 86 cm (0.86m)
- Height from ground to top of enclosure: 278 cm (2.78m)
- Height from top rail to top of enclosure: 192 cm (1.92m)
. The trampoline must be placed on a level surface at least 2m from any structures or
obstructions such as fence, garage, house, overhanging branches, laundry lines or electrical
wires.
. Inspect trampoline / enclosure net before each use. Any damaged or worn parts must be
replaced before using the trampoline (see spare parts page 20).
. If an access ladder is used it should be removed when trampoline is not in use.
. Make sure there are no children / animals / obstructions underneath the trampoline.
. Access the trampoline through the door of the enclosure net only. Making sure you securely
close it before bouncing.
. Please don’t use when it’s windy or rainy as this can cause you slip and become injured.
. Don’t intentionally rebound off the enclosure net as this will weaken it.
. Only attach manufacturer approved accessories to the trampoline and enclosure net.
. Always jump in the middle of the mat and practice bounce techniques safety with adult
supervision and guidance.
and checked in every instance before use.
This trampoline is not intended to be buried in the ground.
Do not install the trampoline over concrete, asphalt or any other hard surface not at proximity of
frames.
.
. Jump without shoe.
. In certain countries during winter period, the snow load and the very low temperature can
damage the trampoline. It is recommended to remove the snow and store the mat and the
enclosure indoor.
JUMPING INSTRUCTIONS
Fundamental Bounce
1. Start from a standing position with
your head erect and your eyes on the
frame pad.
2. Swing your arms forward and up in a
circular motion.
3. Bring your feet together and point
your toes downward while in the air.
4. Keep your feet about 30 cm (15 in.)
apart from when landing on the bed.
Seat Drop
1.
Land in a sitting position with your
legs parallel to the bed.
2. Place your hands on the bed beside
your hips.
3. Push with your hands to return to an
erect position.
Hand and Knee Drop
1.
Start bouncing from a standing
position, keeping your eyes on the
frame pad.
2. Land on the bed on your hands and
knees.
3. Push with your hands and come back
up to an erect position.
Half Turntable
1. Start from the front drop position
and push to the left or right with
your arms to begin turning your body
in the opposite direction.
2. Turn your head and shoulders
toward the direction that your body
is turning.
3. Keep your back parallel to the bed
and your head up.
4. After completing a half turn, land in
the front drop position.
Knee Drop
1. Start bouncing from a standing
position, keeping your eyes on the
frame pad.
2. Land on your knees, keeping your
back straight and your body erect.
3. Come back up to an erect position.
Swivel Hips
1. Start with a seat drop.
2. Turn your head to the left or right
and swing your arms up in the same
direction.
3. Turn your hips in the same direction
as your head and arms, completing a
twist.
4. Land in the seat drop position.
3
IMPORTANT PRECAUTIONS
surface.
1 user allowed at any one time.
This can result in serious injury to head, neck, arms or legs.
4
CARE & MAINTENANCE
Regular care and maintenance of your trampoline is required. This will help prolong its life and reduce
the possibility of injury. Neglecting this can lead to a risk for users.
Inspect your trampoline before each use using the checklist below as a guide. Take particular care in
doing this at the start of each season and at regular intervals. Ensure all parts are intact and cannot
become dislodged during play, tighten any screws or nuts and bolts where required.
IMPORTANT: If any faults are found, the trampoline MUST NOT BE USED. We advise that the
Looking after your trampoline:
If any part becomes dirty, clean with a damp cloth and dry thoroughly. Do
not use any abrasive cleaners as this could damage the product.
Prolonged exposure to sun
and harsh weather can shorten its life.
(available to buy from our website).
Common damage can be caused by water pooling, garden/outdoor debris landing on it, sparks
their claws can damage it.
A trampoline can act like a sail in strong winds. It can be blown over
which can cause damage to the frame and surrounding areas. We recommend that it is moved
to a sheltered location and secured to the ground (tie-down kit available from our website), or
dismantled and stored away.
Follow assembly
instructions in reverse order making sure the springs are removed before dismantling frame.
To be lifted by 2 people. Lift slightly off the ground,
keeping the frame horizontal. Never drag to move it as this can displace parts. Always check that
parts are positioned correctly after moving.
PART
All Parts
Springs
Frame / Enclosure
Poles
Bed / Enclosure
Net / Frame Pad /
Foam Tubes
CHECKLIST
Securely attached
Correctly positioned
No sharp edges or points present
No missing parts
No damage (bent / broken)
No missing parts
No bent parts
No damage
No rusting or corrosion
No missing parts
No sagging
No damage
NOT OKOK
Excess weight and improper use of the trampoline
will damage it and cause it to break easily.
BUILDING YOUR TRAMPOLINE
Description:
Safety glasses
Description:
Cross-head screwdriver
Description:
Mallet
Description:
Gloves
WHAT YOU WILL NEED
1. This is a 2 person build.
2. Time for build is approximately 2 hours.
3. Choose a good location:
(wood chippings, sand or grass).
(7.3m) from ground level, away from
wires, trees and other possible hazards.
(2.5m) around sides, away from walls, fences, structures, tarmac
and other hard surfaces and play areas.
5
6
PARTS LIST
Part A
Part E
Part I
Part M
Part B
Part F
Part J
Part N
Part O
Part C
Part G
Part K
Part D
Part H
Part L
Description:
T
POD-connector
op Tube with
Quantity: 5
Description:
Stitched bed
Quantity: 1
Description:
Top enclosure poles
Quantity: 5
Description:
Enclosure netting
Quantity: 1
Description:
Top Tube with
T-Connector
Quantity: 5
Description:
7” Springs
Quantity: 60
Description:
6.5” Gold Springs
Quantity: 10
Description:
Bottom enclosure
poles
Quantity: 5
Description:
Cords
Quantity: 8
Description:
Leg extensions
Quantity: 10
Description:
Spring tool
Quantity: 1
Description:
Quantity: 30
Description:
Centre legs
Quantity: 5
Description:
Frame pad
Quantity: 1
Description:
Black G3 poles
Quantity: 2
Sections
Self tapping screws
and spring washers
STEP 1 : ASSEMBLING THE FRAME
You will need the following parts to complete
section 1:
5 x Top Tubes with POD-connector - Part A
5 x Top Tubes with T-connector - Part B
5 x Centre legs
- Part C
10 x Leg extensions
- Part D
First we will complete one of the 5 sections of
the trampoline frame.
Insert the leg extensions into upright tube on
POD-connector
Note: You may need to tap the leg extension in
using a rubber mallet or by placing a piece of
wood over the top of the tube. Do not use a metal
hammer on the metal tube as this may distort the
end of tube.
Slot the centre leg onto the top of the leg
A
B
Top tube
Centre leg
Leg extension
Top tube
A
B
7
25 x Self tapping screws and washers
- Part K
You will also need a cross-head screwdriver (not
supplied).
Self tapping screw and washer
Cross-head screwdriver
Screw one of the self tapping screws through the
slot in the POD or T-connector and into the hole in
the leg extension using the cross-head
screwdrive
Screw one of the self tapping screws through the
slot in the Leg extension and into the hole in
the Centre leg using the cross-head screwdriver.
r.
Making the trampoline upside down with the
top rails curving away from you. Slot the
narrow end of the top tube with POD-connector into T-connector B.
Ensuring the lettered stickers on the POD-connector and T-connector are facing outwards
and you are able to see a spring hole through
the gap of the POD-connector.
8
Slot another leg extension onto the other end of
the centre leg.
Important: The frame is held together under
tension so you will have to use some force to
insert certain parts.
Place your feet on the top tubes and grip the leg
extension with both hands.
Pull the extension until it can be slotted into the
connection (1
Slot the end of leg extension into the connection
(2
Push down on the end of the centre leg to fully
inset the leg extension into the T-connection.
Repeat the last six steps until you have
assembled the 5 sections of the trampolines
frame.
You have now completed step 1.
Screw one of the self tapping screws through the
slot in the T-connector and into the hole in
the leg extension using the cross-head
screwdriver.
STEP 2 : ASSEMBLING THE FRAME
This step will require 2 people who must be
wearing gloves.
Slot two of the frame section together as shown in
the diagram.
9
POD
At this point you will need to ensure you can see
spring holes in the gaps of the POD-connector.
10
Locate the 5 V-rings with Green webbing.
These will be at 72 to each other.
Slot one of the springs Part GE onto one of the green
webbing V-rings as shown.
Important: springs must be slotted on the right way
around.
Green
webbing
Slot the other end of the spring through
POD-connector to the right side into one of
the spring slots in the top of the frame.
IMPORTANT: Ensure the spring is fully
inserted into the slot on the top of the
frame.
11
green webbinggold
green webbing
Continue to attach springs in the same sequence
as above: In the middle of the new sections,
making sure the next spring is attached on the
opposite side of the new spring to even out the
tension around the trampoline.
POD-connector
POD-connector
O
On the right side of each POD connector
using Gold Springs.
Once you have the 5 Green V rings
attached continue attaching the rest of the
Gold springs to the left side of the POD
connector.
You will then need to attach all the silver
springs to the top side of the frame.
Keeping D rings free for under springs.
Once you have attached all of the top springs,
complete this section by attaching all the under
springs.
12
STEP 4 : FITTING THE FRAME PAD
This step will require 2 people.
Lay the frame pad - Part H out over the edge of
the frame with the ties facing downwards.
Align the openings in the frame pad with the
POD-connector's on the frame.
completed step 4.
WARNING: The trampoline MUST NOT be used
during construction.
STEP 5 : FITTING THE ENCLOSURE TUBES
You will need the following parts to complete step 5:
5 x Top enclosure tubes - Part I
5 x Bottom enclosure tubes - Part J
5 x Self tapping screws and washers
- Part K
You will also need a cross-head screwdriver (not
supplied).
Slot the thin end of one of the bottom enclosure
tubes into the open end of one of the top
enclosure tubes.
Align the hole in the bottom enclosure tube with
the slot in the top enclosure tube.
Screw one of the self tapping screws through the
slot in the top enclosure tube and into the hole in
the bottom enclosure tube using the cross-head
screwdriver.
Top enclosure tube
Bottom enclosure tube
Self tapping screw and washer
Cross-head screwdriver
13
Please note the screw is larger than the hole.
Some force will be needed to screw this in.
14
Slot the bottom enclosure tube into the tubes in
the POD-connector tubes visible through the slots in
the frame pad.
Assemble the remaining enclosure tubes
using the self tapping screws and the
cross-head screwdriver.
Slot the remaining enclosure tubes into the
4 remaining POD-connector's on the frame.
completed step 5.
STEP 6 : FITTING THE ENCLOSURE NETTING
You will need the following parts to complete step 6:
2 x Black G3 poles - Part L
1 x Enclosure netting - Part M
Lay the enclosure netting out on the trampoline.
Find the sleeves that run along the top of the
enclosure netting.
Slot the thin sections on the two black G3 poles
into the metal ends so the poles become two long
sections.
Black G3
poles
Enclosure
netting
15
16
Slot one of the Black G3 poles through three of
the sleeves on the top of the enclosure netting.
Slot the remaining Black G3 poles through the
three other sleeves on the top of the enclosure
netting.
You will now join the two ends of the Black G3
will require two people.
Both people hold two of the poles end sections
and walk towards each other to bend the poles
into a circle.
As soon as the poles are bent enough, insert the
connectors into the socket on the other pole (1
Push the pin inwards (2
connector.
Ensure the pin is protruding through the slot in the
socket.
You may need to slide the connected poles around
in the nettings sleeves until the thin black sections
are aligned with the gaps between sleeves.
Attach the other exposed sections of the
Black G3 pole to the other enclosure tubes in the
order shown in the diagram.
completed step 6.
17
5
With the netting hanging on the inside of the
enclosure poles, stand on the trampoline and
insert one of the exposed sections of the Black
G3 pole into a plastic grip on top of one of the
enclosure tubes.
18
STEP 7 : ATTACHING THE BOTTOM OF THE NET
You will need the following parts to complete step 7:
8 x Cords - Part N.
Tie the non-plastic end of the cord around a
V-Ring. Push the plastic end through a hole in
the bottom of the netting.
Important: Keep the cord tight at all times.
Slot plastic end of the cord through the middle
of the next V-Ring along.
Now slot the plastic end back through the net
and down through the next V-Ring. Continue to do
this until you have used up nearly all the cord then
tie this end around a V-Ring.
Tie another cord to this V-Ring and continue until
all of the net is tied down.
From the underside of the trampoline, tie the
remaining elastic straps around the springs or
through the V-Rings.
You have completed step 7 and the trampoline is
fully assembled.
USING THE TRAMPOLINE
To enter the trampoline, unzip the door and climb
in.
Always close the doorway before using the
trampoline.
Ensure that there is 7.3 metres (24 feet) clearance
above the trampoline.
Also check that there area no overhanging objects
in the area above the trampoline.
7.3m
24ft
Before using your trampoline, check again that
there is enough clearance around it. Maintain a
clear space of 2.5 metres (8.2 feet) on all sides of
the trampoline.
Also check that the area is free from walls,
structures, fences, tarmac and other hard surfaces
and other play areas.
Door
zip
12ft (3.66m)
8ft8in (2.69m)
19
2.5m
8.2ft
SPARE PARTS
For a full range of accessories and replacement parts call 0344 800 4060
or visit our web site at: www.jumpking.eu
To order replacement parts, you can email us on: customerservice@yjeurope.co.uk, or call our
Customer Helpline on: 0344 800 4060.
To help us assist you, please provide the following information when calling:
12 FT (3.66M) JUMPKING CLASSIC PREMIUM TRAMPOLINE
(see parts list below).
17
10
12
13
14
15
18
19
11
9
16
3
T-Connector
4
POD-Connector
20
20
POD-connector
POD-connector
Loading...