Page 1
User Guide
14ft x 17ft Oval POD, Deluxe and Capital Ultra
Got a Problem building your trampoline?
Call us on 01276 855 600 and we can help
WARNING: Read these assembly instructions carefully
before attempting to assemble or use this product. Keep
this user guide in a safe place for futurereference.
Made In China
Page 2
IMPORTANT INFORMATION
. WARNING! ADULT SUPERVISION & GUIDANCE REQUIRED AT ALL TIMES.
. Recommended age 6+ years.
. No somersaults or flips - can cause serious injury.
WARNINGS!
. Only for domestic use.
. Maximum user weight limit 140 kg.
. Not suitable for children under 36 months - small parts, choking hazard.
. Outdoor use only.
. The trampoline should be assembled by an adult in accordance with assembly instructions
and checked in every instance before use.
. Only one user. Collision hazard.
. Always close the net opening before jumping.
. Remove footwear before jumping on the trampoline.
. Do not use the mat / jumping bed when it is wet.
. Empty pockets and hands before jumping.
. Always jump in the middle off the mat / jumping bed.
. Do not eat whilst jumping.
. Do not exit by a jump.
. Limit the time of continuous usage (make regular stops).
. Do not use in strong wind conditions and secure the trampoline.
. The net should be changed every 1 year.
ADVISORY
.
This trampoline is not intended to be buried in the ground.
. The following product dimension relate to this 14ft x 17ft Oval trampoline:
-
Height from ground to top rail: 89cm (0.89m)
-
Height from ground to top of enclosure: 281cm (2.81m)
-
Height from top rail to top of enclosure: 192cm (1.92m)
. The trampoline must be placed on a level surface at least 2m from any structures or
obstructions such as fence, garage, house, overhanging branches, laundry lines or electrical
wires.
.
Do not install the trampoline over concrete, asphalt or any other hard surface not at
proximity of other conflicting installation, such as paddling / swimming pools, swings,
slides or climbing frames.
. Inspect trampoline / enclosure net before each use. Any damaged or worn parts must be
replaced before using the trampoline (see spare parts page 19).
. If an access ladder is used it should be removed when trampoline is not in use.
. Make sure there are no children / animals / obstructions underneath the trampoline.
. Access the trampoline through the door of the enclosure net only. Making sure you securely
close it before bouncing.
. Please don’t use when it’s windy or rainy as this can cause you slip and become injured.
. Don’t intentionally rebound off the enclosure net as this will weaken it.
. Only attach manufacturer approved accessories to the trampoline and enclosure net.
. Always jump in the middle of the mat and practice bounce techniques safety with adult
supervision and guidance.
. Jump without shoes.
. In certain countries during winter period, the snow load and the very low temperature
can damage the trampoline. It is recommended to remove the snow and store the mat
and the enclosure indoor.
2
Page 3
3
IMPORTANT PRECAUTIONS
surface.
1 user
allowed at any one time.
This can result in serious injury to head, neck, arms or legs.
JUMPING INSTRUCTIONS
Fundamental Bounce
1. Start from a standing position with
your head erect and your eyes on the
frame pad.
2. Swing your arms forward and up in a
circular motion.
3. Bring your feet together and point
your toes downward while in the air.
4. Keep your feet about 30 cm (15 in.)
apart from when landing on the bed.
Knee Drop
1. Start bouncing from a standing
position, keeping your eyes on the
frame pad.
2. Land on your knees, keeping your
back straight and your body erect.
3. Come back up to an erect position.
Hand and Knee Drop
1. Start bouncing from a standing
position, keeping your eyes on the
frame pad.
2. Land on the bed on your hands and
knees.
3. Push with your hands and come back
up to an erect position.
Seat Drop
1. Land in a sitting position with your
legs parallel to the bed.
2. Place your hands on the bed beside
your hips.
3. Push with your hands to return to an
erect position.
HalfTurntable
1. Start from the front drop position
and push to the left or right with
your arms to begin turning your body
in the opposite direction.
2. Turn your head and shoulders
toward the direction that your body
is turning.
3. Keep your back parallel to the bed
and your head up.
4. After completing a half turn, land in
the front drop position.
Swivel Hips
1. Start with a seat drop.
2. Turn your head to the left or right
and swing your arms up in the same
direction.
3. Turn your hips in the same direction
as your head and arms, completing a
twist.
4. Land in the seat drop position.
Page 4
4
CARE & MAINTENANCE
Regular care and maintenance of your trampoline is required. This will help prolong its life and reduce
the possibility of injury. Neglecting this can lead to a risk for users.
Inspect your trampoline before each use using the checklist below as a guide. Take particular care in
doing this at the start of each season and at regular intervals. Ensure all parts are intact and cannot
become dislodged during play, tighten any screws or nuts and bolts where required.
IMPORTANT:
If any faults are found, the trampoline
MUST NOT BE USED
. We advise that the
PART CHECKLIST OK NOT OK
All Parts
Securely attached
Correctly positioned
No sharp edges or points present
No missing parts
Springs
No damage (bent / broken)
No missing parts
Frame / Enclosure
Poles
No bent parts
No damage
No rusting or corrosion
Bed / Enclosure
Net / Frame Pad /
Foam Tubes
No missing parts
No sagging
No damage
Looking after your trampoline:
Excess weight and improper use of the trampoline
will damage it and cause it to break easily.
If any part becomes dirty, clean with a damp cloth and dry thoroughly. Do
not use any abrasive cleaners as this could damage the product.
and harsh weather can shorten its life.
Prolonged exposure to sun
(available to buy from our website).
Common damage can be caused by water pooling, garden/outdoor debris landing on it, sparks
their claws can damage it.
A trampoline can act like a sail in strong winds. It can be blown over
which can cause damage to the frame and surrounding areas. We recommend that it is moved
to a sheltered location and secured to the ground (tie-down kit available from our website), or
dismantled and stored away.
Follow assembly
instructions in reverse order making sure the springs are removed before dismantling frame.
To be lifted by 2 people. Lift slightly off the ground,
keeping the frame horizontal. Never drag to move it as this can displace parts. Always check that
parts are positioned correctly after moving.
Page 5
5
BUILDING YOUR TRAMPOLINE
1.
This is a 2 person build.
2.
Time for build is approximately 2 hours.
3.
Chooseagood location:
(wood chippings, sand or grass).
(7.3m) from ground level, away from
wires, treesand other possible hazards.
(2.5m) around sides, away from walls, fences, structures, tarmac
and other hard surfaces and play areas.
WHAT YOU WILL NEED
Description: Description:
Cross-head screwdriver Gloves
Description: Description:
Safety glasses Mallet
Page 6
6
PARTS LIST
Part B
Part G
Part F
Part I
Part L
Part Q
Part R
Part S
Part T
Part J
Part O
Part P
Part C
Part N
Part M
Part
H
Part K
Part D
Part E
Part A
Description:
Quantity: 2
Description:
Top tube with
A marking
Top tube with
B marking
Description:
Quantity: 2
Top tube with
E marking
Top tube with
C marking
Quantity: 2
Description:
Stitched bed
Quantity: 1
Description:
Top enclosure poles
Quantity: 8
Description:
Enclosure netting
Quantity: 1
Description:
7inch Springs
Quantity: 82
Description:
Bottom enclosure
poles
Quantity: 8
Description:
Cords
Quantity: 8
Description:
Cap connector
Quantity:
8
Description:
Spring tool
Quantity: 1
Description:
Quantity: 24
Description:
L legs
Quantity: 8
Description:
V legs
Quantity: 4
Description:
Frame pad
Quantity: 1
Description:
Black G4 poles
Quantity: 2
Self tapping screws
and spring washers
Description:
Quantity: 2
Top tube with
F marking
Quantity: 2
Top tube with
D marking
Description:
Quantity: 2
Description:
7inch Springs
Quantity: 16
Page 7
7
STEP 1 : ASSEMBLING THE FRAME
Youwillneed the following parts to complete
section 1:
2 x Top tube with A marking
2 x Top tube with B marking
2 x Top tube with C marking
2 x Top tube with D marking
8 x L legs
4 x V legs
- Part A
- Part B
- Part C
- Part D
2 x Top tube with E marking
- Part E
2 x Top tube with F marking
- Part F
- Part G
- Part H
16 x Self tapping screws and washers
- Part Q
Youwillalsoneed a cross-head screwdriver (not
supplied).
y
Fisrt
ou will need to assemble the leg bases
of your OvalPOD. This will require 2 x L-legs
and 1 x V Leg.
Note:
Do not screw the sections together yet.
Lay out the 2 x L-legs and 1 x Centre Leg so that it
makes a ‘W’ shape. Join the three pieces so the
screw holes line up.
Repeat this step with the remaining pieces to
make 4 x ‘W Legs’. Leave to one side when
finished.
Layout Top Rail B, Top Rail A and Top
Rail C curving away from you as if
you are making the trampoline
upside down and a
ach. You should
only
be able to see 2 spring holes
on each top rail.
A
A
B
B
C
Layout Toprail D, E and F cu rving
away from you and ensuring you can
top rail. Connect Top rail D together
sleeve on top rail D is on the left
side. Attach this to the other top rails.
D
D
E
E
F
Assemble 1 (A, B, C)
Assemble 1 (D, E, F )
only see 2 spring holes on each
A
B
C
D
E
F
H
Self tapping screw and washer
Cross-head screwdriver
G
Page 8
8
You will need two people for this next step.
C
E
E
B
B
D
A
A
D
F
F
C
Insert 1 end of W-leg partially into Connector A.
Next place feet either side of POD-Connector B.
Then pull other end of W-leg into POD-Connector B.
(You will need to use force for this step)
Now push down on W-leg so inserted fully in each
POD-connector.
Repeat with other W-Legs
Now you have 4 completed segments
2 x Assembly 1 (ABC)
2 x Assembly 2 (DEF)
B
C
F
A
B
C
D
E
F
E
D
Turn over 1 x Assembly 1 (ABC) and 1 x
Assembly 1 (DEF)
Join by inserting C into POD-connector
D. (Make sure spring hole lines up with
gap in connector)
Repeat this step so you are left with 2
halves of Trampoline
Carefully join the 2 halves together.
For the last section, you will need
someone to stand on the opposite side
if the frame and push towards you
whilst you insert Top-rail into PODConnector.
A
Page 9
9
Locate the V-rings with coloredwebbing.
T
hese will be at 180
to each other.
Slot one of the springs onto one of the colored
webbing V-rings as shown.
Important: springs must be slotted on the right way
around.
Colored
webbing
J
Page 10
C
D
A
A
D
E
E
B
B
F
F
C
ing hole
10
Continue to attach springs in the same sequence as above: in the middle of of each section, making sure the
next spring is attached on the opposite side to even out the tension.
Important: The stitched bed is designed like elastic to be bouncy, which means that during construction it may
look like it won’t fit. Please note that it will stretch to the correct size when attaching the springs, this may take
some force.
The stitched bed is now filled and you have completed step 3.
This diagram shows the initial order of spring attachment.
= Top spring hole
= Bottom spr
Important: Attach the springs in the
order shown in the diagram. This will
help to distribute the tension, making
assembly easier.
Firstly, locate the 2 colored V-rings.
These V-rings are to be attached at
points 1 and 2 using a silver spring.
Then attach gold springs 3 to 20 in
the order shown in the diagram.
These are all gold top springs that
attach to the POD-connector, as
shown below:
Important: Remenber to include the
‘under spring’ holes when counting
the V-rings on the frame and bed.
Once all of the springs shown in the
diagram have been fitted, the remaining springs can be attached.
Then please attached the ‘under
springs’ (10) to the underside of the
toprail.
1
17
13
15
19
14
18
16
20
2
3
7
4
8
5
10
6
9
Page 11
STEP 4 : FITTING THE FRAME PAD
This step will require 2 people.
Lay the frame pad
- Part K
out over the edge of
the frame with the ties facing downwards.
Align the openings in the frame pad with the
POD-connector'sontheframe.
completed step4.
WARNING:
The trampoline
MUST NOT
be used
during construction.
11
Page 12
12
STEP 5 : FITTING THE ENCLOSURE TUBES
Top enclosure tube
Youwillneed the following parts to complete step 5:
Bottom enclosure tube
8 x Top enclosure tubes - Part M
8 x Bottom enclosure tubes
- Part L
8 x Self tapping screws and washers
- Part P
Self tapping screw and washer
You will also need a cross-head screwdriver (not
supplied).
Cross-headscrewdriver
Slot the thin end of one of the bottom enclosure
tubes into the open end of one of the top
enclosuretubes.
Align the hole in the bottom enclosure tube with
the slot in the top enclosure tube.
Screw one of the self tapping screws through the
slot in the top enclosure tube and into the hole in
the bottom enclosure tube using the cross-head
screwdriver.
Page 13
13
Slot the bottom enclosure tube into the tubes in
thePOD-connector tubes visible through the slots in
the framepad.
Assembletheremaining enclosure tubes
using the self tapping screws and the
cross-head screwdriver.
Slot the remaining enclosure tubes into the
remaining POD-connector’s on the frame.
have completed step 5.
Page 14
14
STEP 6 : FITTING THE ENCLOSURE NETTING
Youwillneed the following parts to complete step 6:
Black G4
2 x Black G4 poles
- Part N
poles
1 x Enclosure netting
- Part O
Enclosure
netting
Lay the enclosure netting outon the trampoline.
Find the sleeves that run along the top of the
enclosurenetting.
Slot the thin sections on the two black G4 poles
into the metal ends so the poles become two long
sections.
Page 15
15
Slot one of the Black G4 poles through three of
the sleeves on the top of the enclosure netting.
Slot the remaining Black G4 poles through the
three other sleeves on the top of the enclosure
netting.
Youwill now join the two ends of the Black G4
will
poles together with the fitted pole connectors, this
require two people.
Both people hold two of the poles end sections
and walk towards each other to bend the poles
into a circle.
As soon as the poles are bent enough, insert the
connectors into the socket on the other pole (
1
Push the pin inwards
and fully insert the
(
2)
connector.
Ensure the pin is protruding through the slot in the
socket.
Page 16
16
Youmayneed to slide the connected poles around
in the nettings sleeves until the thin black sections
are aligned with the gaps between sleeves.
Stand on the trampoline and insert one of the
exposed sections of the Black G4 pole into a
plastic grip on top of one of the enclosure tubes.
5
6 7
8
Attach the other exposed sections of the
Black G4 pole to the other enclosure tubes in the
order shown in the diagram.
completed step6.
Page 17
17
STEP 7 : ATTACHING THE BOTTOM OF THE NET
Youwillneed the following parts to complete step 7:
8 x Cords
- Part R
.
From the underside of the trampoline, tie the
remaining elastic straps aroundthe springsor
through theV-Rings.
Youhave completed step 7 and the trampoline is
fullyassembled.
Push 1 end of a cord through a hole in the bottom of
the netting.
Then tie this end to a V-ring on the bed.
Important: Keep the cord tight at all times.
Slot the other end of the cord through the next
V-ring.
Then slot back through the net and into the next
V-ring. Continue to do this untill you have used most
of that cord and tie end to next V-ring.
Tie another cord to same V-ring and repeat until net
is sewn in.
Page 18
USING THE TRAMPOLINE
2.5m
8.2
Before using your trampoline, check again that
there is enough clearance around it. Maintain a
clear space of 2.5 metres (8.2 feet) on all sides of
thetrampoline.
Also check that the area is free from walls,
structures, fences, tarmac and other hard surfaces
and other play areas.
7.3m
24
Ensure that there is 7.3 metres (24 feet) clearance
above thetrampoline.
Also check that there area no overhanging objects
in the area above the trampoline.
14 x 17 (4.27m x 5.18m)
Toenter the trampoline, unzip the door and climb
in.
Always close the doorway before using the
trampoline.
18
Door
zip
Page 19
SPARE PARTS
For a full range of accessories and replacement parts call 01276 855 600
or visit our web site at: www.capitalplay.co.uk
To help us assist you, please provide the following information when calling:
(see parts list below).
23
19
22
19
10
11
21
16
17
Key
No. Qty. Description
Key
No. Qty. Description
5
4
3
6
8
7
9
12
13
14
15
18
20
24
12
13
3 2 Top rail (5 top / 4 bo om, C marking)
4 2 Top rail (4 top / 4 bo
om, D marking)
5 2 Top rail (4 top / 3 bo
om, E marking)
6 2 Top rail (6 top / 4 bo
om, F marking)
24
8
8 8 L legs
9 4 V legs
10 82 7” length springs
11 16 7” length gold springs
12 1 Jumping mat
13 1 Safety pad
14 8 Enclosure bo
om poles
15 8 Enclosure top poles
16 16 Foam sleeve
17 2 G4 FRP
18 1 Enclosure mesh
19 1 User manual
20 8 Plas c caps
21 1 Spring tool
22 24 Screw + spring washer
23 8 PP rope
Plas
c caps for connector
1 2 Top rail (4 top / 3 bo
om, A marking)
2 2 Toprail (4 top / 4 bo
om, B marking)
7 8 POD-connector
(2 pcs A marking, 2 pcs B marking, 2 pcs D marking, 2 pcs E marking)
14ft x 17ft Oval POD, Deluxe and Capital Ultra.
Customer Helpline on:
01276 855 600
To order replacement parts, you can visit us on: www.capitalplay.co.uk, or call our
Page 20
Page 21
Loading...