Jumbl Mini Portable Car Jump Starter User Manual
.
Mini Portable
Car Jump Starter
w/Power Bank & LED Flashlight
Introduction
Thank you for purchasing our Mini Portable Car Jump
Starter, and welcome to the Jumbl™ family. This user
manual is meant to offer you a brief walkthrough of
the device’s features and usage protocols. We hope
you nd this manual helpful. For additional information
and technical support, please feel encouraged to
contact our help team at info@itsjumbl.com.
- Do not touch red and black clamps to each other or
connect both to same piece of metal. Risk of serious
physical injury and vehicle damage.
- If corrosive liquid seeps out from unit and comes in
contact with your eyes, immediately wash eyes with
running water and consult a doctor.
- If corrosive liquid seeps out from unit and comes in
contact with your skin, immediately wash thoroughly
with soap and water.
- Do not use included jump-start cable for any
purpose other than jump-starting your vehicle.
- KEEP AWAY FROM CHILDREN AT ALL TIMES.
Usage & Safety
Whether in the event of car battery failure or another
emergency, or as a camping and hiking gadget, this
rugged device is designed to jump-start your vehicle
and recharge your mobile devices many times over. It
will also provide you with a reliable source of bright
white light as well as a ashing strobe and SOS
emergency indicator.
Be sure to follow these safety instructions. Failure to
do so may result in electrical re, electrical shock and
vehicle damage:
- DO NOT throw device or apply physical shock
to housing.
- NEVER attempt to disassemble unit.
- Keep away from re, heat and water.
- Only use supplied AC and DC adapters to charge.
- Only charge device at temperatures between 32°F
and 140°F.
- If device appears abnormal in shape, immediately
stop usage and disconnect all electronic devices.
Box Contents
1 x Mini Portable Car Jump Starter
1 x Dual Clamp Jumper Cable
1 x Wall Outlet Charger
1 x DC Car Charger
1 x USB to Adapter Cable
1 x Apple 30-Pin Adapter
1 x Apple Lightning Adapter
1 x PSP Adapter
1 x Mini USB Adapter
1 x Micro USB Adapter
1 x User Manual
Parts & Controls
1. Light Mode Button
2. LED Bulb Enclosure
3. Jumper Cable Socket
4. DC Charging Port
5. USB Output A
6. Battery Level Indicators
7. USB Output B
Operation
Charging & Power:
At the heart of the Mini Portable Car Jump Starter is
a 12,000mAh battery pack.
- For wall charging, choose the included Wall
Outlet Charger.
- Plug larger end into wall outlet, and insert smaller
end into DC Charging Port (4).
- Battery Level Indicators (6) will cycle to show that
device is charging.
User Manual
7
. USB Output B
1
2
3
4
7
5
6
www.ItsJumbl.com
JUMBL is a trademark of C&A IP Holdings,LLC
©2014 All Rights Reserved
Distributed by C&A Marketing, Inc., 2 Bergen Turnpike,
Ridgefield Park, NJ 07660
1-866-849-3049
MADE IN CHINA
-
.
Technical Specications
Battery Capacity: 12000 mAh
Battery Life Cycles: >500
Outputs: 2 x 5V/2.1A, 1 x 12V/10A
Input: 12V/1A
Jump Start Current: 200 - 400A
Dimensions: 6.5” x 2.9” x 1.2”
Bulb Type: Bright White LED
Bulb Lifespan: 100,000 hours
Bulb Energy Draw: 1 Watt
Bulb Brightness: 86 Lumens
Built-In Protection: - Overcurrent Protection
- Short-Circuit Protection
- Overload Protection
- Overvoltage Protection
- Overcharge Protection
Troubleshooting
- To charge device from your car, choose the included
DC Car Charger.
- Charging takes 2-3 hours, depending on current
charge levels.
- Once device is fully charged, all Battery Level
Indicators (6) will remain lit.
Note: While some vehicles can supply a DC charge
even when the engine is off, others cannot. Be sure
to check your vehicle’s manual for specications, and
check that Battery Level Indicators (6) are showing
the device being charged.
- To check remaining power levels at any time, unplug
all cables from device and short-press the Light
Mode Button (1). Consult the following chart:
Note: On a full charge, unit’s standby time is about
3 months. It is recommended that the device be
charged once every 3 months to prolong its
service life.
Using the LED Light:
- Press and hold the Light Mode Button (1) for 2
seconds to turn on the ashlight.
- Press and hold again for 2 seconds to switch to the
ashing strobe mode.
- Press and hold again for 2 seconds to switch to
SOS emergency mode.
- Press and hold again for 2 seconds to turn light off.
Charging Mobile Devices:
The two built-in 5V USB ports can charge many
different mobile devices. Use the included USB to
Adapter Cable and choose the adapter made for
your device.
- Connect larger end of USB cable to either of the
USB outputs (5 & 7).
- Select proper adaptor and insert it into smaller end
of USB cable.
- Connect adaptor to mobile device and short-press
Light Mode Button (1) to start charge.
- Both USB outputs may be used simultaneously to
charge separate devices.
- Thanks to an output current that can reach 2A,
most mobile phones will charge to full in just 2 hours,
which is much faster than most factory chargers.
- Once the connected mobile device reaches full
charge, charging will stop automatically.
Jump-Starting a Vehicle:
On a 100% charged battery, the device can power
approximately 20 jump-start sessions. Results may
vary depending on owner usage and vehicle engine
displacement. We recommend using the Mini
Portable Car Jump Starter for vehicles with the
following engine displacements: 4.0 displacement for
gas/petrol-powered vehicles, and 3.0 displacement
for diesel-powered vehicles.
- Ensure that device battery capacity is above 50%.
To check power levels, shortpress Light Mode Button
(1) and check that at least 3 Battery Level Indicators
(6) stay on.
Indicators All Off All Flashing 1 On 2 On 3 On 4 On 5 On
Charge 0% 10% 20% 40% 60% 80% 100%
- Connect the included Dual Clamp Jumper Cable to
your vehicle’s battery by placing the red clamp on the
positive “+” terminal and the black clamp on the
negative “-” terminal.
- Insert the cable’s other end into the Jumper Cable
Socket (3).
- Attempt to start the engine. If engine does not start,
wait at least 10 seconds before attempting to start
the engine again.
- After the engine has been successfully started,
disconnect the cable from the Jumper Cable Socket
(3) within 10 seconds.
- For your safety and that of your vehicle, the device is
designed with reverse polarity protection. If you
accidentally connect the red and black clamps to the
wrong polarity terminals and attempt to jump-start the
vehicle, the fuse will blow and cut power immediately
to prevent injury and damage.
Issue Cause Solution
All Battery Level
Indicators (6) stay
lit while charging,
but battery is NOT
at maximum
capacity
Device is at about
60% battery
capacity due to
long-term storage
without use
Unplug charging
adapter then
reinsert into DC
Charging Port (4)
No response when
pressing Light
Mode Button (1)
Low Voltage
Protection has
been activated
and electronic
circuit has been
shut off
Plug charging
adapter into DC
Charging Port (4) to
activate electronic
circuit
Quick battery drain
on rst use out
of box
Battery requires
full charge prior
to rst use
Perform a full
battery drain and
charge for a full 12
hours without use
Loading...