JUMBL JUBTPASO1 User Manual
Transfer Pump
User Guide
JUBTPASO1
Thank you for purchasing the Jumbl® Transfer Pump. This User Guide is intended to provide you with
guidelines to ensure that operation of this product is safe and does not pose risk to the user. Any use
that does not conform to the guidelines described in this User Guide may void the limited warranty.
Please read all directions before using the product and retain this guide for reference. This product
is intended for domestic use only. It is not intended for commercial use.
This product is covered by a limited one-year warranty. Coverage is subject to limits and exclusions.
See warranty for details.
SAFETY PRECAUTIONS
DANGER: FUEL IS EXTREMELY FLAMMABLE. DO NOT SMOK E OR USE AN OPEN
FLAME NE AR THE PUMP.
• Don’t use this pump until you thoroughly read and understand all of the operation instructions and
warnings. Deviating from these instructions could result in re, explosions, property damage, and/
or operator injury. Don’t try to operate this device without reading the instructions.
• Make sure to familiarize yourself with the appliance itself before using it.
• Before using this appliance, check all the parts to make sure they function properly, and make sure
no components have been damaged.
• Keep out of the reach of children.
• Always keep away from heat or ame, and avoid prolonged exposure to sunlight.
• Don’t use a leaking, damaged, or malfunctioning pump. If it’s ever damaged, do not use it, and
immediately contact the authorized ser vice center for assistance.
• Pumps that are improperly operated, maintained, or repaired are dangerous! Improper use, service
repair, or modication of the pump could result in damage to the product, property damage, or
personal injury to the operator.
• Do not inhale gas, fumes, vapor, or spray of fuel, and avoid contact with skin and eyes. If inhaled,
immediately move the affected person to fresh air. For skin contact, ush with lots of water. In case
of eye contact, rinse immediately with plenty of water and then seek medical advice.
• Storage tanks should be securely anchored to prevent shifting or tipping when full or empt y.
• Do not use without liquid. Take care to make sure that liquid does not run out while pump is in operation.
• Do not use with thinner or other solvents.
• Do not use with corrosive liquids.
• Before using pump, make sure that any hot sur faces have cooled down.
• Do not position or store the pump upside-down after use.
• Remove batteries when not in use.
• The pump is not intended for use with drinking water.
Package Contents
• Transfer pump
• User guide
1
Features
• Battery operated for portability
• Auto-Stop feature prevents overow
• Transfers liquids at a rate of 2.3 gallons per minute
• No seal required
• For use with gasoline, kerosene, diesel, light oils, and non-potable water
• Great for emergency generators, yard equipment, and utility machinery
Product Overview
Discharge hose with clip and nozzle
Intake tube
How to Assemble Your Pump
1. Install 2 new D batteries, making sure the polarity on
the batteries matches the polarit y indicators
embossed just above the threaded area of the
battery casing. Do not install different types of
batteries or partially-charged batteries.
2. Screw the sides of the bat tery casing back together,
using a clockwise motion.
3. Ensure that the discharge hose is rmly seated
before use.
BATTERY CASE
TURN COUNTER CLOCKWISE TO OPEN
Battery casing/
pump unit
Power switch
BATTERIES
How to Use Your Pump
1. Check the unit over before each use to make sure
there are no holes in the tubes or hoses.
2. Immerse the intake tube into the supply tank from
which you wish to transfer uid.
3. Place the nozzle of the discharge hose into the tank
to which you wish to transfer uid, and use the
included clip to hold it in place.
4. Turn the power switch on to begin transferring liquid.
5. Pump will stop automatically when the receiving tank is full.
You can also stop the pump manually by turning the power
switch off.
6. If you wish to transfer liquid from a new container, you must
turn the power switch off, immerse the intake tube into the
new container, and then restart the pump.
ON
2
INTAKE
TUBE
OFF
SUPPLY
TAN K
DISCHARGE
HOSE
RECEIVING
TAN K
Loading...