Julian Bowen Limited
Atlas White Metal Bunk Bed
Assembly Instructions
VERSION: 160701
IMPORTANT - READ CAREFULLY - RETAIN
FOR FUTURE REFERENCE
White Gloss
02
HARDWARE
PARTS
1
03
B
C
2x
A
99x 7x 60x
D
2
3
4
5
6
7
8
9
9
9
9
10
11
12
13
14
14
15
16
17
18
18
18
18
E
16x
F
4x4x
G
H
8x
Parts F,G & H are required to
convert to 2 single beds
S a f e t y A d v i c e
Please take the time to carefully read through the whole of these instructions before
you commence.
Keep these instructions for future reference.
Unpack, inspect and check off all of the contents.
Please dispose of all packaging safely.
Small component parts could choke a child if swallowed.
We strongly recommend that you keep children well away from the work area.
It would be sensible to lay a sheet or blanket on the floor where you intend to work
to avoid scratching this product and to protect your floor.
This product is heavy. Take extreme care when lifting to avoid personal injury or
damage to the product.
Assemble the product as close to its intended final position in the room as possible.
HANDY HINT: If you keep the hardware in a bowl during assembly you will be less
likely to lose them.
04
Tighten firmly all the fittings when the assembly is complete.
The bed base is an integral and indissociable part of the bed.
WARNING: High beds and upper bed of bunk beds are not suitable for children
under six years due to the risk of injury through falls.
It is not safe to use this product if any part of the structure is missing or broken.
Children could strangle themselves with articles, such as ropes, strings, cords,harnesses
and belts attached to or hung on this product.
WARNING: Children can become trapped between the bed and the wall. To avoid risk
of serious injury the distance between the top safety barrier and the wall shall not
exceed 75mm or shall be more than 230mm.
The largest size of the mattress recommended is : 190 x 91 x 20cm.
The bed has been tested to ensure compliance with BS EN 747-1:2012 + A1:2015.
I m p o r t a n t I n f o r m a t i o n
155cm
2
0
1
.
5
c
m
9
9
c
m
ATLAS BUNK BED
Product Code - ATL001/ATL004
Distributed by:
Julian Bowen Lim ited
Bentick House ,
Park Lane Busi ness Park,
Kirkby-in-Ashfield,
Notts, NG17 9LE
Factory ID: Manufactured in China
Date of Manufacture: Jun 2 015
CERTIFICATION LABEL
This bunk bed model has
been tested by an independent
laboratory and is in compliance
with EN 747-1:2012 +A1:2015
- Standard Consumer Safety
Specification For Bunk Beds
WARNING : This upper bed is not suitable for children under six years
1
2
05
1
3
4
5
6
7
8
2
x12
x4
18
9
9
9
9
18
18
18
A
D
A
D
10
11
12
13
x4
D
A
x16
D
A
A
C
D
x60
x3
A
D
14
15
3
06
4
x3
x3
B
D
B
D
16
17
15
WARNING:
THE MATRESS
SURFACE MUST NOT
BE ABOVE THIS LINE
x1
B
D
08
G e n e r a l C a r e
Wipe clean with a slightly damp soft cloth.
Avoid the use of all household cleaners and abrasives.
When moving your furniture, carefully lift into place.
Never drag or push the pieces across the floor as this
will cause damage to the joints and could result in failure to
the product that will invalidate the warranty.
R e c o m m e n d a t i o n s
Periodical re-tightening of fixings.
W a r n i n g
This unit is heavy. Please use an assistant when lifting.
N o t e s
Weʹve tried to make this piece of furniture as easy to
assemble as possible.
In the unlikely event that you have problems putting
it together or have damaged or missing pieces,
please contact our customer services on 01623 727374
Julian Bowen Limited
Bentinck House, Park Lane Business Park, Kirkby-in-Ashfield, Notts, NG17 9LE
www.julian-bowen.co.uk
Loading...