Music
Life
INFINITY
2
IN
6
4
TB
SET
-
+
2
IN
6
4
R
59508-021-02
REMOSET
▲
SET ▲
AF
RF
AF
RF
UHF PLL Dual Channel Diversity Wireless System
* The system is of the innovative design to allow changing the
transmitter’s frequency by long-distance .
* IN264R with band width of 36 MHz.
* Preset 6 groups, maximum 23 channels in one group.
▲
SET ▲
REMOSET
IN
2
6
4
Music
Life
1. Important Caution
2. Features
3. Parts Identification
INFINITY
01
01
02
3-1 IN264R
02
1. Important Caution
Always make all connections before plugging the unit into an AC power outlet.
Do not leave the devices in a place with high temperature or high humidity.
Do not handle the power cord with wet hands !
Keep the devices away from re and heat sources.
Pair the ID codes of the transmitter and the receiver to have proper function.
3-2 IN264TH
3-3 IN264TB
3-4 Accessories
4. Connection
4-1 Connect to the subsequent unit
4-2 Connect the power supply unit
5. Operation
5-1 Set up the system
5-2 Set up ID code
5-3 Synchronize the channel
5-4 Check system status
5-5 Manual select channel
5-6 REMOSET button lock
5-7 Adjust the sensitivity of the microphone
6. Specification
03
04
04
05
05
05
06
06
06
07
08
09
10
11
13
2. Features
JTS IN264 wireless microphone system is designed with the world rst RF
remote setting function (REMOSET). A user can set the receiver with desired
frequency and press the “REMOSET” Key; then the transmitter will automatically be
set. The operation distance can reach 10 meters. This brings great convenience to
sound engineers during live performance.
IN264 is of 36MHz bandwidth to render 23 transmitters work simultaneously.
It provides great convenience to large venue.
A new capsule has been developed for IN264TH . The capsule, SAM-8W, is
designed for large venue with hundreds of thousands watt power. The SAM-8W
delivers vivid details of vocal and instruments.
The IN264 is of stylish industry design. Yet JTS bombproof quality remains as
always.
IN
2
6
01
4
Music
Life
INFINITY
3. Parts Identification
3-1 IN264R
Front panel
1
Power Switch
2
IN
6
4
R
2
Channel Selector:
3
LCD Panel
4
REMOSET Key:
6
▲
REMOSET
Rear panel
5
6
7
8
9
10
11
SET ▲
BNC antenna connector
Power Supply Jack (12-18V/600mA):
Squelch adjuster: to adjust radio signal level of both channels
Mixed AF Output (6.3mm jack, unbalanced): for connection to a balanced input,
e.g. of a mixer or amplier
Balanced XLR Output: for connection to the balanced input, e.g. of a mixer or an
amplier
Output Level Attenuation(-10dB,-20dB): to attenuate the balanced XLR output
LIFT / GND
including “ up”, “ down” and “Set” button
press it to send a desired channel data to a transmitter
5 56789 1011 109
LCD Panel of the Receiver
AF Level: display the strength of audio signal
a
RF Level: display the strength of radio signal
b
Antenna Status: the receiver will automatically select an antenna with stronger signal level
c
d
Low battery indicator: display the low battery status of its transmitter
e
Group & Channel: there are 6 groups, maximum 23 channels in one group.
c
d
a
1224 433
AF
RF
7
AF
RF
for connecting the power supply unit
level by 10dB,20dB
▲
SET ▲
REMOSET
3-2 IN264TH
12
LCD Display
13
Battery Tray
14
Set button:
Up button: select the settings of transmitter
15
16
Down button: select the settings of transmitter
17
Power and Mute Switch
LCD Panel of the Handheld Transmitter
Battery status: display battery status
f
g
Group & Channel: there are 6 groups, maximum 23
channels in one group.
f
AF
RF
b
set the conguration of
handheld transmitter
g
e
12
16
17
15
14
13
02 03
IN
2
6
4
Music
Life
INFINITY
3-3 IN264TB
LCD Display
18
Battery Tray
19
20
Set button:
Up button: select the settings of transmitter
21
22
Down button: select the settings of transmitter
23
4 Pin mini XLR mic. input
Power Switch
24
Gain control:
25
26
Pad: -20dB, -6dB, 0dB
LCD Panel of the Body-Pack Transmitter
Battery status: display battery status
h
Group & Channel: there are 6 groups, maximum 23 channels in one group.
i
18
19
3-4 Accessories
27
AC/DC adaptor
AF output cable
28
(with Φ6.3 plug at both ends)
29
Screwdriver (IN264TB)
30
CM-501 (IN264TB)
set the conguration of bodypack transmitter
control sensitivity of the transmitter
20 21 22
h
4. Connection
4-1 Connect to the subsequent unit (e.g. mixer, or amplier)
Connect one end of a proper AF cable to the AF Output or Balanced XLR
Output socket , then plug another end to the “MIC IN” input socket of a
mixer or a amplier (Step 1 of Figure 1)
4-2 Connect the power supply unit
Plug in one end of AC/DC adaptor cable to Power Supply Jack in the
rear panel of receiver, and plug another end into an AC outlet
(Step 2 of Figure 1)
24
26
25
23
-
i
27
-20 -6 0
28
29
30
MIXER
Figure 1
10
27 7
1
AUDIO OUTPUT
DC INPUT
2
9
04 05
IN
2
6
4
Music
SET ▲
▲
Life
INFINITY
5. Operation
5-1 Set up the system
A) Turn on the power of the receiver
Switch the “Power Switch” to “ON”. The “LCD Panel” and “REMOSET”
5
Key will light up.
Turn on the power of the transmitter
B)
Press the “Power Switch” . The “LCD Display” will light up.
C) Mute Function ( for IN264TH )
After the transmitter's power is on, short pressing the "Power Switch "
will mute the microphone. Press the "Power Switch" again will re-activate
the microphone.
Notice: You have to hold the "Power Switch" for 3 seconds in order to turn
o the transmitter.
Install the antennas in a vertical position
D)
5-2 Set up ID code
In order to match one receiver channel to one transmitter, IN264 is
designed with“ ID code”. If and only if both ID codes of a receiver channel
and a transmitter match each other, the “REMOSET” function works. When
setting the ID code, system will automatically avoid the ID code used by
the other channel. There are 100 ID codes available.
Receiver
A) Press "Set" button for 3 seconds, LCD Panel will start ashing.
B) Press "Set" to enter "ID Code"
setting window. (Figure 2)
C) Press " Up" or Down" button to
select a distinct ID code from "id 0"
to "id 99".
D) After setting, press "Set" again to
save the setting.
2
17 24 12
1 6
3
Figure 2
Handheld and BodyPack transmitter
ID code ON/OFF setting
A) Press "Set" button for 3 seconds, LCD Panel will
4
18
17
start ashing.
B) Press "Set" a couple of times until "ID Code ON/OFF" setting window shows.
C) Press " Up" or " Down" button to select between " ID ON " and " ID OFF ".
D) After setting, press "Set" again to save the settings.
Caution
When ID code is o (idOFF), the transmitter will accept any
synchronization from any IN264R.
ID code selecting
A) Press "Set" button for 3 seconds, LCD Panel will start ashing.
B) Press "Set" a couple of times until "ID Code" setting window shows.
C) Press " Up" or " Down" button to select a
distinct ID code from " id 0" to "id 99 ". (Figure 3)
D) After setting, press "Set" again to save the setting.
Figure 3
14 20
14 20
3”
-
2
IN
6
4
TB
3”
SET
-
+
06 07
IN
2
6
4
Music
SET ▲
▲
AF
RF
REMOSET
SET ▲
▲
AF
RF
SET ▲
▲
AF
RF
Life
INFINITY
5-3 Synchronize the channel
A) Press "Set" button on the receiver for 3 Seconds, the group (G) in the
"Group & Channel" area will ash. (Figure 4)
B) Press " Up" or " Down" button to select a desired group
C) Press "Set" again and the Channel (CH) in the "Group & Channel" area
will ash.
D) Press " Up" or " Down" button to select a desired channel.
E) After setting, press “Set” again to save the settings.
F) Press "REMOSET" to synchronize the channel of a transmitter.
(Figure 5)
G) If the channel of the transmitter fails to change, the "REMOSET" key will
keep ashing.
Notice 1: The transmitter has to be set to "synchronization on
(SYnOn)" in order to allow the receiver to synchronize.(Handheld and
body Pack Setting List p.12 )
Notice 2 : When setting the channel, system will automatically avoid
the channel used by the other channel.
Figure 4
5-4 Check system status
A) Antenna Status: the receiver will automatically select an antenna with
stronger signal reception and highlight that antenna (Figure 6)
B) Battery indicator: the receiver’s battery indicator will show the same
gauge as the transmitters. If the transmitter is under low battery status,
the receiver LCD backlight will be on amber.
e
4
Figure 5
c
5-5 Manual select channel:
Receiver
A) Press "Set" button for 3 seconds, the group (G) in the "Group & Channel"
area will ash. (Figure 8)
B) Press " Up" or " Down" button
to select a desired group.
C) Press "Set" again and the Channel
(CH) in the "Group & Channel"
area will ash.
D) Press " Up" or " Down" button
to select a desired channel.
E) After setting, press “Set” again to save the setting.
Scan Function
A) Press "Set" button for 3 seconds, the group (G) will ash.
B) Press "Set" to enter “Sn OF” or “Sn On”.
C) Press " Up" to select “Sn On” , press " Down" to select “Sc OF” .
D) If select “Sc On” , when select channel, the receiver will jump over a
channel in use automatically.
Handheld and BodyPack transmitter
A) Press "Set" button for 3 seconds, the group (G) will ash. (Figure 9)
B) Press " Up" or " Down" button to select a desired group.
C) Press "Set" again and the Channel (CH) will ash.
D) Press " Up" or " Down" button to select a desired channel.
E) After setting, press “Set” again to save the setting.
Figure 8
2
IN
6
4
3”
AF
RF
Figure 6
08 09
AF
RF
Figure 7
Figure 9
IN
2
TB
3”
SET
-
+
6
4
Music
SET ▲
▲
AF
RF
Life
INFINITY
5-6 Lock ON Function
Receiver
A) Press "Set" button for 3 seconds to enter setting window
B) Press "Set" again until the Lock setting window shows. (Figure 10)
Notice: Original setting is lock o (Lo OF).
C) Press " Up" or " Down" button to
select the mode between "Lock On"
and "Lock o".
D) After setting, press "Set" again to
save the setting.
To release the “Lock ON”
A) Press “Set” for 2 seconds.
B) Press “down” to select “Lock OFF”.
C) Press “Set” to store.
Handheld and BodyPack transmitter
A) Press "Set" button for 3 seconds to enter setting window. (Figure 11)
B) Press "Set" again until the Lock setting window shows.
Notice: Original setting is lock o (Lo OF).
C) Press " Up" or " Down" button to select the mode between "Lock On"
and "Lock o".
D) After setting, press "Set" again to save the setting.
To release the “Lock ON”
A) Press “Set” for 2 seconds.
B) Press “down” to select “Lock OFF”.
C) Press “Set” to store.
Figure 10
5-7 Adjust the sensitivity of the microphone
Handheld transmitter
A) Press "Set" button for 3 seconds to enter
setting window.
B) Short press "Set" until the sensitivity
setting window shows.
C) Press " Up" or " Down" button to
select the sensitivity among 0db,
-3db, -6db, -9db, -12db, -15db, -18db
and -21db.
D) After setting, press "Set" again to
save the setting.
BodyPack transmitter
A) Use the screwdriver included to adjust the
sensitivity from gain control . (clockwise is "increase")
B) If further adjustment is needed please adjust the pad.
5-8 Adjust the transmitting power
Handheld/Body Pack Transmitter
A) Push the "Set" button several times until the "rF Lo " or "rF Hi" ashes.
B) Then push "Up" to choose "Hi" for high transmitting power and push
"Down" to choose "Lo" for low transmitting power.
C) Push the "Set" again to save the setting.
(Figure 12)
Figure 12
29
25
26
3”
2
IN
6
4
3”
Figure 11
10 11
TB
3”
SET
-
+
IN
2
6
4
Music
Life
INFINITY
6. Specification
Sensitivity
Settings
Synchronization
ON/OFF
ID code ON/OFF
ID code select
Lock ON
Handheld and Body Pack Setting List
0 dB is the highest sensitivity
“On” means “REMOSET” function always opens;
“OFF” means “REMOSET” function is turned o
When ID code is OFF (id OFF), the transmitter will
accept any synchronization from any IN264R.
~
There are 100 ID codes.
button unlock
button lock
6-1 IN264R
Frequency Preparation....
Remoset............................
Carrier Frequency Range
S/N Ratio............................
T.H.D..................................
Display...............................
Display Contents..............
Controls.............................
Audio Output Level..........
AF Output Impedance......
Squelch..............................
Operation Voltage.............
Output Connector.............
Dimension(m/m)...............
6-2 IN264TH
Frequency Preparation.........
Carrier Frequency Range.....
RF Outputs............................
Stability..................................
Frequency Deviation.............
LCD Display...........................
Controls.................................
Spurious Emissions.............
Audio Frequency Response
Battery....................................
6-3 IN264TB
Frequency Preparation........
Carrier Frequency Range....
RF Outputs............................
Stability.................................
Frequency Deviation............
LCD Display..........................
Controls................................
Output connector.................
Spurious Emissions.............
Audio Frequency Response
Battery...................................
PLL Synthesized Control
Radio Frequency : 2.4GHz
Effective distance: 10m
502~960 MHz
>105dB
<0.6%@1KHz
LCD
Channel, Antenna A/B, Mute Display, RF/AF Level Meter,
Low battery, ID Number
Power On/Off, Frequency Up/Down, Lock-on, ID Pairing, Remoset
-12dB
ȍ
Pilot Tone & Noise Mute
12-18 VDC, 600 mA
2 XLR Balanced Socket / 1 Ø6.3mm unbalanced phone jack
420mm(W) * 44mm(H) * 211mm(D)
PLL Synthesized Control
502~960 MHz
10mW
±10KHz
±48KHz
Channel, Battery Fuel Gauge,
ID Number
Power On/Off, AF Level, Frequency
Up/Down, Lock-on Mode,ID Pairing
<-50 dBC
50~16,000 Hz
UM3, AA 1.5V*2
PLL Synthesized Control
502~960 MHz
10mW
±10KHz
±48KHz
Channel, Battery Fuel Gauge, ID Number
Power On/Off, AF Level,
Frequency Up/Down, PAD, Gain Control
Lock-on Mode, ID Pairing
4P mini XLR
<-50 dBC
40~18,000 Hz
UM3, AA 1.5V*2
12 13
IN
2
6
4
Loading...