Instruction Manual
DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM
US-9030DC Pro
US-9020D Pro
ank you for choosing the JTS wireless system. In order to obtain the best eciency from the system,
you are recommended to take few minutes to read this instruction manual carefully.
1. Important Caution
2. Features
3. Specication
3-1 Receiver
3-2 Handheld Transmitter
3-3 Body-pack Transmitter
3-4 Optional Condenser Microphone
4. Part Identication & Accessories
4-1 Receiver
4-2 Handheld Transmitter
4-3 Body-pack Transmitter
4-4 Optional Condenser Microphone
4-5 Accessories
5. Preparing Procedures & Basic Operation
5-1 Receiver
5-2 Handheld Transmitter
5-3 Body-pack Transmitter
5-4 Installation of Condenser Microphones
6. System Operation
7. Recommendation
1
1
2
2
3
3
4
7
7
9
10
11
14
15
15
17
18
19
21
22
INDEX
WIRELESS MICROPHONE SYSTEM
1
1. Important Caution
2. Features
Make all connections before plugging the unit into an AC power outlet.•
Do not leave the devices in a place neither with high temperature nor high humidity.•
Do not headle the power cord with hands!•
Keep the devices away from re and heat sources.•
e systems operate in the UHF band, that there is less interference than the VHF band.•
Equipped with S.A.W. lter for eectively reducing the spurious RF interference content and •
present only focused incoming signal.
Built-in noise mute and squelch circuity mode can resist the interference validly.•
e tuned antennas are able to benet the optimum reception.•
e Anti-interference design makes the system available to work with every computer device.•
2
3. Specication
3-1 Receiver
Model No...................................
Frequency Preparation.....
Carrier Frequency Range
Frequency Stability..............
S/N Ratio...................................
T.H.D.............................................
Display...........................................
Display Contents...................
Controls.......................................
Audio Output Level............
AF Output Impedance......
Squelch.........................................
Operation Voltage................
Output Connector...............
Dimension(m/m)................
US-9020D Pro / US-9030DC Pro
Crystal
600~960 MHz
±10KHz
> 105dB
<0.6%@1KHz
LCD
Frequency, Antenna A/B, RF/AF Level Meter
Power On/O, Squelch Level, Audio Level
-12dB
600Ω
Pilot Tone, Noise and Mute
US-9020D Pro: 12-18 VDC, 350mA
US-9030DC Pro: 12-18 VDC, 900mA
2 Balanced XLR Sockets
1 Unbalanced Ø6.3mm Phone jack
420mm (W)* 44mm (H)* 232mm (D)
WIRELESS MICROPHONE SYSTEM
3
3-2 Handheld Transmitter
3-3 Body-pack Transmitter
Model No.........................................
Frequency Preparation............
Carrier Frequency Range......
RF Outputs......................................
Stability...............................................
Frequency Deviation................
LED Display....................................
Controls..............................................
Spurious Emissions....................
Audio Frequency Response
Baery..................................................
Model No. .........................................
Frequency Preparation..............
Carrier Frequency Range........
RF Outputs.......................................
Stability.................................................
Frequency Deviation.................
LED Display......................................
Controls...............................................
Spurious Emissions.....................
Audio Frequency Response
Baery...................................................
Mh-900 / Mh-910 / Mh-700 / Mh-800 / Mh-8000(i)
Crystal
600~960 MHz
10mW
±10KHz
±48KHz
Low Baery, Power On/O
Power On/O
<-60 dBC
50~16,000 Hz
UM3, AA 1.5V*2
PT-900B
Crystal
600~960 MHz
10mW
±10KHz
±48KHz
Power On/O, Low Baery
Power On/O, AF Level
<-50 dBC
40~18,000 Hz
UM3, AA 1.5V*2
4
3-4 Optional Condenser Microphone
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
Dimension(mm)..............
Net Weight............................
CM-501
4P Mini XLR
100~15,000 Hz
Cardioid
-60±3 dB
2.2kΩ
130dB
Ø10.1mm(W)
* 26.4mm(H)
21.5g
CM-201
4P Mini XLR
60~15,000 Hz
Omni-directional
-60±3 dB
2.2kΩ
130dB
Ø5mm(W)
* 9mm(H)
20.7g
CM-125
4P Mini XLR
50~18,000 Hz
Omni-directional
-53±3 dB
4.4kΩ
130dB
Ø4mm(W)
* 11mm(H)
7g (cable excluded)
Lavaliere Microphone // CM-501 CM-201 CM-125
WIRELESS MICROPHONE SYSTEM
5
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
Dimension(mm)..............
Net Weight............................
CM-225
4P Mini XLR
50~18,000 Hz
Omni-directional
-53±3 dB
4.4kΩ
130dB
155mm(W)
* 134mm(H)
* 157mm(D)
17g (cable excluded)
CX-504
4P Mini XLR
30~18,000 Hz
Cardioid
-68±3 dB
680Ω
130dB
285mm(W)
* 55mm(H)
* 111.3mm(D)
56.3g
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
Dimension(mm)..............
Net Weight............................
CM-204
4P Mini XLR
60~15,000 Hz
Omni-directional
-60±3 dB
2.2kΩ
130dB
125mm(W)
* 134mm(H)
* 157mm(D)
32.9g
CM-204U
4P Mini XLR
30~18,000 Hz
Cardioid
-68±3 dB
680Ω
130dB
205mm(W)
* 134mm(H)
* 157mm(D)
38.4g
CM-204UL
801C3 (3 pin mini XLR)
801C4 (4 pin mini XLR)
801CS (3.5 stereo plug)
100~18,000 Hz
Cardioid
-75±3 dB
1.5kΩ
120dB
125mm(W)
* 134mm(H)
* 157mm(D)
18g (cable excluded)
Headset Microphone // CM-204 CM-204U CM-204UL CM-225 CX-504
6
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
CX-508W
4P Mini XLR
50~18,000 Hz
Cardioid
-67±3 dB
220Ω
130 dB
CX-516W
4P Mini XLR
50~18,000 Hz
Cardioid
-67±3 dB
220Ω
130 dB
Instrument Microphone // CX-508W CX-516W
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
CM-801/CM-804i
801C3 (3 pin mini XLR)
801C4 (4 pin mini XLR)
801CS (3.5 stereo plug)
60~15,000 Hz
Omni-directional
-64±3 dB
1.8kΩ
130dB
CM-8015/CM-825i
801C3 (3 pin mini XLR)
801C4 (4 pin mini XLR)
801CS (3.5 stereo plug)
50~18,000 Hz
Omni-directional
-53±3 dB
1.2kΩ
130dB
Ear-hook Microphone // CM-801 CM-804i CM-8015 CM-825i
WIRELESS MICROPHONE SYSTEM
7
4. Parts Identication & Accessories
4-1 Receiver //
US-9020D Pro
UHF Dual Channel Diversity Receiver
Power Switch
LCD Panel
Volume Control
Antenna
Squelch level adjustor
DCV Input (12-18 VDC, 350mA)
Unbalanced Ø6.3mm jack socket
Balanced XLR socket
1
4
7
2
5
8
3
6
7 6
12
5
8
3
4
8
US-9030DC Pro
UHF Dual Channel Diversity Receiver
Power Switch
Baery Charger
Charging Indicator(Red)
Charged Indicator(Green)
LCD Panel
Volume Control
Antenna
Squelch level adjustor
DCV Input (12-18 VDC, 900mA)
Unbalanced Ø6.3mm jack socket
Balanced XLR socket
13
16
19
15
18
14
17
9
10
12
11
13
16
19
15
18
14
17
9
10
12
11
WIRELESS MICROPHONE SYSTEM
9
Interchangeable Dynamic Capsule
Baery Tray Buon
Baery Tray
Power On/O Switch
Power Indicator
4-2 Handheld Transmitter //
Mh-900 / Mh-910 / Mh-800 / Mh-700
22
24
23
Mh-900
Mh-700
Mh-910
Mh-800
POWER
Low Batt.
POWER
Low Batt.
POWER
Low Batt.
POWER
Low Batt.
21
20
22
22
22
22
24
24
24
24
23
23
23
23
21
21
21
21
20
20
20
20
10
Interchangeable Dynamic Capsule
Baery Tray
Power On/O Switch
Mh-8000 / Mh-8000i
Mh-8000iMh-8000
27
29
26
28
25
30
32
33
34
31
Mic. input
Power On/o switch
Power Indicator
Antenna
AF level control
Baery tray
Baery tray cover
Carry case
Belt-loop
4-3 Body-pack Transmitter // PT-900B
36
35
27
26
25
29 28
30
32
33
34
31
36
35
WIRELESS MICROPHONE SYSTEM
11
Clip
4 Pin Mini XLR
Windscreen
4-4 Optional Condenser Microphone
Lavaliere Microphone // CM-501 CM-201 CM-125
CM-501 CM-201 CM-125
38
37
39
38
38
38
37
37 37
39
12
Gooseneck
Headband
4 Pin Mini XLR
Windscreen
Headset Microphone // CM-204 CM-204U CM-204UL CM-225 CX-504
CM-204 CM-204U
CM-225
CM-204UL
CX-504
43
40
42
41
43
43
43
43
43
40
40
40
40
40
42
41 41 41
4141
WIRELESS MICROPHONE SYSTEM
13
Boom
Adjustable Headband
Adjustable ear hook
Detchable Cable
Cable Clip
Windscreen
4 Pin Mini XLR
3 Pin Mini XLR
3.5 Stereo Plug
Gooseneck
Clip
Bracket
Windscreen
4 Pin Mini XLR
56
57
55
Instrument Microphone // CX-508W CX-516W
Ear-hook Microphone // CM-801 CM-804i CM-8015 CM-825i
CM-801
CM-8015
CM-804i
CM-825i
CX-508W CX-516W
52
54
51
47
49
50
48
45
46
44
52
53
51
47
47
47
47
49
49
49
49
50
48
48
48
48
45
45
46
46
46
46
44
44
44
44
57
54
53
56 56
53
55
14
62
63
61
60
58
59
AC/DC adaptor
Switching Power Supply(100V~240V , 50~60Hz)
Linear Power Supply (220V , 50Hz)
Linear Power Supply (220V , 60Hz)
Screwdriver
RM-12 Rack mount kit
AF output cable (with Ø6.3 plug at both ends)
GC-80/GC-100 Guitar Cable
GC-80L/GC-100L Guitar Cable
4-5 Accessories
Option
Option
Option
A
B
C
A
B C
62 63
61
60
58
59
WIRELESS MICROPHONE SYSTEM
15
5. Preparing Procedures & Basic Operation
5-1 Receiver
(1) Audio Output Connector
Connect one end of the AF output cable to the AF output socket in the rear panel, then plug
another end to the “MIC IN” input socket of a mixer or amplier. (Step 1)
It is equipped with balanced XLR output and unbalanced Φ6.3mm output, choose the
proper way for use.
(2) Power output connector
Plug in one end of AC/DC adaptor cable to DC input socket in the rear panel of receiver, and
plug another end into an AC outlet. (Step 2)
MIXER
AC/DC ADAPTOR
AC POWER SOCKET
AUDIO OUTPUT
DC INPUT
2
1
(3) Turn the receiver on by pressing the Power buon on
the front panel
(4) Adjust the volume control to a proper level.
16
Using the baery charger of US-9030DC Pro
1. Push the charger’s tray and put 4 pcs of rechargeable baeries into the baery tray. Please
match the correct polarity (+ and -) , then return the tray for charging the baeries.
2. It is convenient to know the charging status via the LED indicator. e two red LED will
ash during charging and as soon as the baeries is fully charged, the two red LED will
light up.
Caution
To avoid baery leakage or explosion
(1) Remove baeries when the wireless microphones will not be used for a long time.
(2) When you need to replace the baeries, replace both baeries at the same time with new
ones.
(3) Don’t use dierent type of baeries together!
WIRELESS MICROPHONE SYSTEM
17
(1) Turning the transmier on/o
e on/o switch is located on the boom of the microphone.
(2) Inserting and changing the baery
1. Loosen the microphone head counter-clockwise. (Figure 1)
2. Hold on to both baery tray buons to release it. (Figure 2)
3. Insert 2 pieces of UM-3 1. 5 V baeries, remember to match
correct polarity. (step1 of Figure3)
4. Directly push the baery tray back. (step2 of Figure3)
5. Aim the connectors exactly for screwing on the microphone
head clockwise. (Figure 4)
(1) Loosen the baery cover and put the two 1.5V baeries into the baery tray.
(2) Aer puing into the baery, switch on the power on/o on the boom side of microphone.
5-2 Handheld Transmitter //
Mh-900 / Mh-910 / Mh-800 / Mh-700
Mh-8000 / Mh-8000i
Figure 1
Figure 4
Fig
ure 2
2
1
Fig
ure 3
18
5-3 Body-pack Transmitter // PT-900B
(1) Basic operation
1. Slide the baery tray cover in the direction of the
arrow to open it, insert two 1.5V baeries according
the correct polarity, and return the cover.
2. Switch the transmier On
e On/O switch is located on the top of the
transmier.
3. Sensitivity adjusting
ere is a gain control adjustor in the up-le of its
back, you can adjust the level in 3 steps from 0 dB
to 30 dB.
AUDIO ADJUSTING STICKER
AF LEVEL CONTROL
ON/OFF
(2) Wearing the Body-pack transmier
e carry case allows body-pack transmier to be aached on performer’s belt, place the
antenna towards the back of his body. e Velcro tag around the belt and x it.
WIRELESS MICROPHONE SYSTEM
19
5-4 Installation of Condenser Microphones
(1) Lavaliere microphone
Aach lavaliere microphone to a tie, lapel, where is suitable for sound pick-up. Plug the
connector into input socket on the body-pack transmier.
(2) Headset microphone
Put the headband behind your head, and x the temples on your ears as shows, then
adjust the gooseneck to have best miking. Plug the connector into input socket on the
body-pack transmier.
(3) With Wind Microphone
1. Outsanding for saxophone, brass, woodwind instruments.
2. Flesible gooseneck together with adjustable axis allow accurate sound source aiming.
3. Clamp with elastic grip ensures stable holding instrument without damaging.
4. Windscreen to prevent pop noise eectively.
MIC IN
20
(4) Ear-hook Microphone
1. Lightweight Dual Ear Hook Microphone
Try on whether the headset is t.
Adjust the headband to a suitable width.
Tighten or loosen the curve of the ear-hook by twisting the loop or expanding it.
Curve and bend the boom to t your face.
Aach the detachable cable to a suitable place by a cable clip.
2. Lightweight Single Ear Hook Microphone
Try on whether the original curve is tight or loose.
Re-try and push the xed curve against your earlobe.
Curve and Bend the boom to t your face.
Aach the detachable cable to a suitable place by a cable clip.
WIRELESS MICROPHONE SYSTEM
21
6. System Operation
(1) Turn on the system
1. Turn on the power of the receiver and check the indicators to verify signal is well received.
2. Adjust the volume control of the receiver to a proper level.
3. Turn on the power of the amplier and adjust the volume to a proper level. Avoid to
damage the amplier, please turn on the amplier only aer the receiver and transmier is
powered on.
(2) Turn o the system
1. At rst, please decrease the volume of the amplier to a lowest level, then turn o the power
amplier.
2. Turn o the wireless transmier and the receiver.
22
7. Recommendation
(1) In order to achieve the optimum reception condition and also extend the operating distance,
please leave a “open space” between the receiver and transmier.
(2) Keep the devices away from the metal objects or any interference sources, at least 50 cm.
(3) To avoid the feed-back eect, don’t leave the mic. to aim at the speakers directly.
(4) For best pick-up paern, please hold the middle of the mic. body.
(5) Remove baeries from the baery compartment when the transmier will not be used for a
long time.
(6)When you need to replace the baeries, please replace both baeries at the same time with
new ones.
US-9020D Pro / US-9030DC Pro
Mh-900 / Mh-910 / Mh-700 / Mh-800 / Mh8000(i) / PT-900B
59508-001-03
Loading...