JTS CM-501, CM-201i, CM-125, CM-214i, CM-214Ui Instruction Manual

...

59508-085-01

PROFESSIONAL CO., LTD

www.jts.com.tw

/ /

Instruction Manual

UHF PLL

With JTS 2.4G RF Synchronizing Technology

UHF PLL Transmitter

-12dB

IDoff

633.875 MHz

G: 1 C: 11

UF-20TB

1. The warranty card must be presented with the date of purchase and attached at the bottom of the machine to ensure the validity of warranty service.

2. The warranty is valid for one year starting from the date of purchase shown on ''warranty label'' attached to the product; alternatively, the warranty is valid for 15

months starting from the date the product was manufactured if the ''warranty label''

is missing on the machine. If the microphone is returned for service but with the

machine, the warranty is valid for 15 months starting from the date of manufacturing shown on the microphone.

3. If malfunction occurs under normal operations according to the instruction manual while the warranty is still valid, please call the shop where you purchased the

product for warranty service.

4. It is important to return both the machine and microphone back to the shop for service, since this makes it easier to identify where the possible problem is and determine whether a service fee is needed.

5. JTS will provide service free of charge while the warranty is still valid. However, A fee

for parts and/or service may be charged for the following:

a. Damage due to natural disaster or any other irresistible factors;

b. Damage due to dropping, immersion in water, exposure to high humidity, corrosion, ingress of alien objects, or loss of parts; c. Consumables are not part of the warranty; or d. The ''warranty label'' is not found on the machine or the ''warranty label'' is damaged to the point that the validity of warranty is not recognizable.

6. Keep this warranty card at a safe place, as the warranty is invalid with a lost warranty card.

One-Year Warranty Card

Product model Serial number

Customer Phone number

Address

Date of purchase

Distributor’s

shop seal

The distributor’s shop seal and date of purchase are

required for the warranty to be valid!

Warranty Service

Contents

1. Notes for system operations

2 . F e a t u r e s

3. Speci󺸾cations

3-1 UHF PLL 4-channel / 2-channel, diversity receiver 3-2 UHF PLL handheld transmitter 3-3 UHF PLL body-pack transmitter 3-4 Optional Condenser Microphon

4. Parts

4-1 UHF PLL 4-channel / 2-channel, diversity receiver // / 4-2 UHF PLL handheld transmitter // / 4-3 UHF PLL handheld transmitter// / 4-4 UHF PLL body-pack transmitter // 4-5 UHF PLL body-pack transmitter // 4-6 Accessories 4-7 Microphone Choices

5. Connection

5-1 Connecting transmitter 5-2 Installing transmitter // / 5-3 Installing transmitter // / 5-4 Installing transmitter // 5-5 Installing transmitter //

6. Operation

6-1 Operation // / 6-2 Operation // / 6-3 Operation // / 6-4 Operation // 6-5 Operation //

7. Digital Code Alert Function

8. Notes for the product

1. Notes for system operations

2. Features

• Before connecting to the main power supply, check that the power requirements shown on the nameplate of the machine meet the output of the adaptor.

• Do not place the machine at a place where high temperature and humidity are expected.

• Do not operate the system with wet hands.

• Keep the machine away from any heat or ignition source.

• Before setting up the machine, make sure that the volume is set at the minimum for both the mixer and ampli󺸾er.

• The system features the latest anti-interference digital code circuit design that is proven to isolate the interference between the system and the outside world.

• Up to 36MHz of bandwidth with a maximum of 1440 channels to choose from

• Adjustable squelch level

• Default with 6 groups, up to 22 available

• User-de󺸾ned groups provided

• Automatic scan

• Provided with antenna booster power

• JTS patent: the latest RF allows the transmission of not only frequency, but also data such as sensitivity, low cut, transmission power and key lock to the transmitter.

• With one push of the key, upto four transmitters can be synchronized.

• RF ''no signal'' alert on LCD display

• AF ''microphone mute'' alert on LCD display

• Transmitter ''low battery'' alert on LCD display

• Antenna and power cascading for improved performance and convenience.

• Digicode prevents intermodulation

3.Speci󺸾cations

3-1 UHF PLL 4-channel / 2-channel, diversity receiver

Model Frequency oscillation Phase-locked loop, PLL Carrier frequency 470~960 MHz No. of channels 4 channels

2 channels

Channel pairing RF Diversity antenna diversity Bandwidth 36MHz Signal/noise ratio >106dB(A) Total harmonic

distortion

<0.5%@1KHz

Receiving sensitivity -95dBm，S/N>80dB Mirror rejection ratio >80 dB General frequency

response

50Hz~18KHz±2dB

Antenna connector BNC female Antenna booster

power

DC12V/100mA

Display LCD

Functions displayed

Group, channels, frequency, transmitter power, antenna A/B, mute, AF, RF, channel scan, output level, volume, Device ID

Controls

Power ON/OFF, groups, channels, frequency, receiving sensitivity, key lock, volume, output attenuation (XLR), channel scan (ON/OFF), antenna power, display setting

Audio output level

Ref：±22.5KHz Dev@1KHz Tone

ψ6.3 Phone Jack：-10dBV

XLR Jack：-4dBV(Line)、-24dBV(MIC)

Audio output impedance

600Ω

Mute Noise mute and Pilot Tone

Output port

5 balance XLR ports, 1 unbalance φ6.3mm jack

3 balance XLR ports,

1 unbalance φ6.3mm jack

Power 100~240VAC Dimensions 485mm L x 230mm W x 44mm H

Remark

Speci󺸾cations provided above may be slightly different from

the product without further notice.

3-2 UHF PLL handheld transmitter

Model / Frequency oscillation Phase-locked loop, PLL Carrier frequency 470~960MHz Bandwidth 108MHz as per local regulation Paring RF Remoset RF power output 10mW/50mW(as per local regulation) RF stability <±10KHz＠Fc Modulation frequency

deviation

±48KHz

Spurious Emissions <-50dBc

LCD display

Group, channels, frequency, mute, auto off, input

level attenuation, sensitivity adjustment, power

indication, Device ID

Controls

Power, mute, groups, channels, frequency,

sensitivity adjustment, input level attenuation,

auto off, transmission power, key lock

Battery AA Alkaline battery x 2 Charging Yes Dimension

265mm L x 51.2mm W x 51.2mm H

Remark

Speci󺸾cations provided above may be slightly

different from the product without further notice.

Model

Frequency oscillation Phase-locked loop, PLL Carrier frequency

UHF 470~960 MHz

Bandwidth 108 MHz as per local regulation Pairing RF Remoset RF power output 10mW / 50mW (as per local regulation) RF output

Hi / Lo adjustable

Stability

<0.005%

Frequency deviation

±48kHz

LCD display

Group and channel, frequency, power indication,

transmission power, sensitivity, Device ID, username,

gain, low cut

Controls

Power ON/OFF, frequency setting, group, sensitivity,

bass attenuation, pairing ID, frequency pairing,

transmission power adjustment, display contrast,

backlight time setting, Chinese/English selection, key

lock pattern, mute, reset

Harmonic radiation <-50 dBC

Audio frequency response

50KHz~18KHz

Capsule Module

Interchangeable

Battery AA Alkaline battery x 2 / rechargeable battery x 2

Charger CH-2,CH-8 Dimensions

35.5mm L x 50mm W x 253mm H

Remark

Speci󺸾cations provided above may be slightly

different from the product without further

notice.

Model

Frequency oscillation Phase-locked loop, PLL Carrier frequency 470~960MHz Bandwidth 108MHz as per local regulation Paring RF Remoset RF power output 10mW/50mW(as per local regulation) RF stability <±10KHz Modulation frequency

deviation

±48KHz

(Peak)

Spurious Emissions <-50dBc

LCD display

Group, channels, frequency, mute, auto off, input level

attenuation, sensitivity adjustment, power indication,

Device ID

Controls

Power, mute, groups, channels, frequency, sensitivity

adjustment, input level attenuation, auto off, transmission

power, key lock

Input connector 4-pin mini XLR

Controls

Power, mute, group, channel, frequency, sensitivity

adjustment, input level attenuation, auto off

Battery AA Alkaline battery x 2 Charger CH-2 CH-8 Dimension

62.3mm L x 20mm W x 97mm H

Remark

Speci󺸾cations provided above may be slightly different

from the product without further notice.

3-3 UHF PLL body-pack transmitter

Model

Frequency oscillation

PLL Synthesized Control

Carrier frequency

UHF 470~960 MHz

Bandwidth

108MHz as per local regulation

Rf power outputs

Low / High

RF stability

<±10KHz

Modulation frequency

deviation

±48KHz (Peak)

Chassis

Aluminium alloy

Lcd display

Group, Channel, Frequency, Battery Status, GAIN Adjust

Controls

Power ON/OFF, AF Level, Frequency (Up/Down), Lock-on

Mode, REMOSET ID, RF Output Adjust

Input connector

4P Mini XLR

Spurious emissions

<-50 dBC

Audio frequency response

50Hz~18k Hz

Battery

AA NiMH x2

Dimension

62mm W x 80.3mm H x 22.6mm D

Weight

93g

3-4 Optional Condenser microphone

Lavaliere microphone

Headset microphone

Model CM-501 CM-201i CM-125i Output

connector

4-pin mini XLR

Frequency response

100~15,000 Hz 60~15,000 Hz 50~18,000 Hz

Directionality

Cardioid

directionality

Omni-directionality

Sensitivity -60 ± 3dB -60 ± 3dB -53 ± 3dB Output

impedance

2.2K Ω 4.4K Ω

Max. sound pressure allowed

130dB

Dimension (mm)

10.1mm

26.4mm

5mm

x 9mm

4mm

x 11mm

Weight

21.5g 20.7g 7g (cable not included)

Model CM-214i CM-214Ui CM-214ULi

Output connector

4-pin mini XLR 4P/3P mini

XLR/3.5stereo jack

Output connector (optional)

3P Mini XLR/3.5 stereo plug/4P Hirose

jack

4P Hirose jack

Frequency response

60~15,000 Hz 30~18,000 Hz 100~18,000 Hz

Directionality Omni-directionality Cardioid directionality Sensitivity -60 ± 3dB -68 ± 3dB -75 ± 3dB Output

impedance

1.8kΩ 680Ω 1.8kΩ

Max. sound pressure allowed

130dB 120dB

Dimension (mm)

157mm L x

125mm W x

134mm H

157mm L x

205mm W x

134mm H

157mm L x

125mm W x

134mm H

Weight

32.9g 38.4g 18g (cable not included)

Ear-hook microphone

Model CM-235i CX-504 Output

connector

4P-pin mini XLR

Output connector (optional)

3P Mini XLR/3.5 ste-

reo plug/4P Hirose

jack

Frequency response

50~18,000 Hz 30~18,000 Hz

Directionality

Omni-directionality Cardioid

directionality

Sensitivity -53 ± 3dB -68 ± 3dB Output

impedance

1.8kΩ 680Ω

Max. sound pressure allowed

130dB

Dimensions (mm)

157mm L x 155mmWx

134mmW

111.3mm L x 285mmWx

55mmW

Weight 17g 56.3g

Model CM-801 / CM-804i CM-8015 / CM-825i Output

connector

4-pin mini XLR

Output connector (optional)

3P Mini XLR/3.5 stereo plug/4P Hirose jack

Frequency response

60~15,000 Hz 50~18,000 Hz

Directionality Omni-directionality Sensitivity -64 ± 3dB -53 ± 3dB Output

impedance

1.8KΩ

Max. sound pressure allowed

130dB

4. Parts

Power ON/OFF：ON：push once to turn on

OFF：push and hold until ''Power OFF'' is shown on the LCD to turn off.

EXIT：Push exit to cancel a selection or exit from the current menu when R-4/2 is in the ''setting menu.''

Rotary Switch：when in the ''function menu,'' turn the switch to select the desired function; push the switch (or SETUP) to enter the selection and spin the switch to select the setting. Push [SETUP] to save the setting.

SETUP：Push and hold for 2 seconds to enter the vsetting menu.'' Push SETUP to save the setting once the selection and setting are made according to ''3. Rotary Switch.''

Front panel

Rear panel

4-1 UHF PLL 4-channel diversity receiver //

Front panel

UHF PLL 2-channel diversity receiver //

16 1617 1715 14a

REMOSET：When the receiver setting is done, push to

transmit the setting data to the handheld or body-pack transmitter.

LCD display：See ''Receiver LCD display instructions.''

AF: indicates the current strength of audio frequency signals.

RF: indicates the current strength of radio frequency signals.

Key lock: push and hold for 2 seconds to lock all keys, and again to unlock.

Volume keys：push▲/▼keys to adjust the volume between 0 and -31dB.

Selection key：push this button

a. Push SETUP to enter the setting for the selected channel for parameter settings.

b. Push REMOSET to transmit the setting data to the transmitter in this

selected channel.

AC Power Jack：connects 100-240VAC power.

AC power cascading：use AC double power cable (optional) for power

cascading.

XLR audio jack：balanced audio signal output XLR audio jack：balanced audio signal output after mixing

Ø6.3 audio output jack：unbalanced audio signal output after mixing

Antenna A (B) input terminal：BNC antenna input jack that also provides

DC12V/100mA output.

RF signal A (B) output terminal： RF signal output jack; it is possible to

connect the RF A (or B) OUT of the 󺸾rst unit to the antenna A (or B) IN of the second unit with a BNC-BNC signal cable, and then the RF A (or B) OUT of the second unit to the antenna A (or B) IN of the third unit, and so on and so forth. The cascade may consist of up to 10 units to minimize the number of antennas used.

14a

Note: Each cascading may bring1.2dB attenuation to RF signal.

LCD displays

Setting page

Key lock

Antenna power supply ON

Mixed output attenuation ON Receiver channel 1 Receiver channel 2 Receiver channel 3 Receiver channel 4 Output attenuation ON

Antenna selection A/B

Device ID Group/channel

Frequency Transmitter battery 3blocks: R-4TH/R-4THA/R-4TB

microphone is used

5blocks: JSS-4A microphone is used

:waiting for battery

information from transmitter

Volume

Transmitter battery 3blocks: R-4TH/R-4THA/R-4TB

microphone is used

5blocks: JSS-4A microphone is used

:waiting for battery information

from transmitter

:no microphone signal Setting window

Digital code ON

2930 31

3128 27

25 26

22 23 24

32 33

LCD displays

Key lock

Antenna power supply ON

Mixed output attenuation ON Receiver channel

Digital code ON Output level LINE/MIC Antenna selection A/B Volume Transmitter battery 3blocks: R-4TH / R-4THA/R-4TB

microphone is used

5blocks:JSS-4A microphone is used

Group / channel

Frequency

38 39 40 41 38 4044

43 4345

Power ON/OFF：push once to turn on. Push and hold for 2 seconds while

the power is on to turn off. While the power is on, a quick push of this

button will show the Device ID on the LCD display.

Mute：switch up to talk and down to mute while the power is on. If the

power is off, switching up from mute will turn the microphone on. In mute, it is allowed to select 1, 10 or 30 minutes to automatically turn the microphone off.

Battery compartment：it holds 2 UM3, AA 1.5V Alkaline batteries or MiNH

rechargeable batteries.

LED indicator：it shows the microphone's status, including battery power, mute and pairing.

LCD display：it shows the parameter settings of transmitter.

SET：for parameter settings, including frequency, group, channel,

sensitivity, transmission frequency, auto off time, Device ID ,

function (ON/OFF).

Up/down selection keys：they are used with ''SET'' to change parameter settings. Before entering the setting mode, a quick push will show the

Device ID on the LCD display.

LOCK ：push and hold ''LOCK'' for 2 seconds to lock and again to un-

lock. Under ''LOCK'' status MUTE function is still valid.

Charging contact module: if rechargeable batteries are used, charging is

possible with the matching charger.

4-2 UHF PLL handheld transmitter // /

Note：R-4TH is the same as R-4THA except that the battery cover of the R-4THA is made of metal.

RF output power (1 block is 10mW and 2 blocks are 50mW)

Auto off ON

Battery level Key lock Frequency (MHz) Indication of frequency, group and channel

/ LCD displays

4-3 UHF PLL handheld transmitter // /

LCD display SET：for handheld transmitter setting and saving

▲、▼：up and down; used to select the desired item for handheld

transmitter.

Power ON/OFF

(1)Turn the handheld transmitter on

Power on: push the button once to turn on Power off: push and hold for 1 second until the LCD display shows

''power off.''

(2)Mute：while the handheld transmitter is in use (main page on the LCD display)

Mute：push the Power ON/OFF and the display shows ''mute.'' Unmute： push the Power ON/OFF again and the display shows ''unmute.''

(3)Exit setting menu

In the setting menu: push Power ON/OFF to return to main page. In the function setting menu: push Power ON/OFF to return to the setting menu, and again to return to main page.

Battery compartment Charging contact: used with the charger (optional for CH-2 or CH-8) Slide cover Detachable capsule module LED status indication

Green: Power ON

Blue: Remoset done (on for about 5 seconds) Red: battery low Blinking red: mute Blinking red/green: battery low and mute

+ 42 hidden pages

JTS CM-501, CM-201i, CM-125, CM-214i, CM-214Ui Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual