JTECH IntelFlex Installation And Operator's Manual

Draft Copy

Installation, Programming and Operator Guide

Part Number TBD

IntelFlex™Controller

Kitchen System

2

Introduction

Congratulations on your purchase of a JTECH Kitchen Messaging System
containing the IntelFlex Kitchen Controller. Please take a few minutes to review
this manual prior to installing and operating your system.

Please inspect the System upon receipt. If the contents appear to be
damaged, notify the shipper immediately to file a claim and notify JTECH
Customer Care. If components are missing, contact JTECH Customer Care.

If you have any questions or need assistance, please call JTECH Customer
Care at 800-321-6221 or 561-997-0772, option 6.

IntelFlex 20, 40 and 60 Button Systems Introduction

Wait Staff and

Managers Pagers

6Ft, Magnetic Mount
or 35W Antenna Kit
(Optional Equipment)

IntelFlex Kitchen Controller

( Expansion Panels Optional )

IntelFlex 20, 40 and 60 Button Systems Introduction

Managers Buttons (Optional)

System also work with IntelFlex
Desktop Controllers

Remote Panels

Cancel or Expeditor Ability

( Expansion Panels Optional)

Grease

Pencil

Requires

110-240VAC

Draft Copy

Draft Copy

General Specifications

DC Operating Voltage: 13.5VDC 2.4A

Power Adapter 110-240VAC 50-60Hz power adapter
Transmitter Power Output:: 0.1-2 Watts - adjustable using 5 levels.
Keypad Display: 20 Button LED
Modulation: FSK 512 BPS
Protocol: POCSAG
Transmit: 512. 1200, 2400 Baud

Kitchen System with Clamp Bracket Dimensions

7-9/16”

(192.1mm

3-3/16”

6-7/8”

(174.6mm)

(81mm)

11-3/8” (288.9mm)

System Dimension General Specifications

16-5/16” (413.5mm)

1/8 - 2 1/16”
(3.2-52.4mm)

7-5/16”

(185.7mm)

Left Side

9-5/16” (236.4mm)

Adjustable
Threaded
Knob (6mm)

Front View (With Clamp Mount Bracket)

Rear View

Connector Area

(Brackets Attached)

Expansion
Connector

1.3/16”

(30.1mm)

5-1/2”

(139.7m

Right Side

REMOTE EXPANSION

Remote
Connector

4

Draft Copy

Antenna Port: 50 ohm BNC
Antenna (Standard) 6” (153mm) Rotating Whip Stainless Steel”
Operating Frequency: UHF synthesized 450-470 MHz. (standard)
Temperature Stability: -22°to 122°F (-30 to 50°C) at better than 5 ppm
Weight : 2.5-3.0 Lbs (1.14-1.36Kg) -Depending on Mounting

Brackets used.
Weight: (Keypad Only) 1.85-2.35Lbs (0.84-1.1.07Kg) -Depending on
Mounting Brackets Used.

Kitchen System with Wall Bracket Dimensions

4 Mounting Slots
for 1/4” (6-7mm)
Diameter Screws or
Bolts

1-7/16”
(36.5mm)

1-9/16” (39.7mm)

3-3/8” (85.7mm)

3-9/16”

(90.5mm)

Left Side

Rear View

Connector Area

(Bracket Remove)

5 –11/16”
(144.5mm)

6-1/2”-

(165.1mm)

Left Side

Rear View (With Wall Mount

bracket)

EXPANSION REMOTE

Remote
Connector

System Dimension General Specifications

8-1/8” (206.4mm)

Expansion
Connector

5

Draft Copy

Kitchen System with Wall Bracket Dimensions

6-7/8”

(174.6mm)

7-9/16”

(192.1mm)

6-7/8”

(174.6mm)

System Dimension

Expansion/Remote

(Bracket Attached)

Left Side
View

Rear View

Connector Area

9” (228.6mm)

Front View (With Clamp

Mount Bracket)

EXPANSION

12” (304.8mm)

Right Side
View

REMOTE

Expansion
Connector

6

Remote
Connector

Draft Copy

IntelFlex Kitchen System Highlights

• Designed for used in restaurant kitchens and

similar applications.

• Available in 20, 40 and 60 button systems with 20

buttons per Panel.

• Connect additional panels for Expeditor or

Server Cancel functions.

• Page up to 60 Wait Staff Pagers and one or more

Manager Pagers at any time (depending on

programming).

• Displays pages when sent and are cleared after a

programmable length of time.

• Use the Controller’s 2X or 3X buttons to

change the number of vibrations sent to
the Wait Staff’s Pagers.

• Number of vibrations sent, can be locked by the

user.

• Add a Managers Button for additional control.

System Highlights

• Range:

• Maximum transmitter range is 1½-2 miles (2.4-

3.2Km).

• Range will vary, depending on the equipme nt

location and surrounding environment.

• Increase range with an optional Magnetic Mount

Antenna, 6ft Antenna or Extended Range Kit (FCC
license required).

• USB & Ethernet Connections:

• USB 2.0 port for Flash Drive software

upgrades or Keyboard support.

• IP addressable Ethernet port for paging

support “online” and software upgrades.

7

Draft Copy

Expeditor or Server Cancel Panels (Optional)

Panels: Additional Panels can be connected to the Controller. The Panels

can then be programmed for cancel or expedite modes.

When a Panel is programmed for

“Cancel Mode” , it will:

• Require Wait Staff to cancel their page at the Cancel Panel.

• Continue to repeat the page after a specific period of time, until the

Wait Staff cancels their page.

• Page the Manager if the Wait Staff does not cancel the page within

specific period of time.

• Contact a Manager or group of Managers at any time if needed.

• Connect up to 25ft (7.6m) away from the Kitchen Controller.

When a Remote Panel is programmed for “Expedite Mode”, it will:

• Page Wait Staff from a alternate location.

• Contact a Manager or group of Managers at any time if needed.

• Connect up to 25ft (7.6m) away from the Kitchen Controller.

Expeditor Panel Cancel Panel Optional Panels

8

Draft Copy

Accessories (Optional)

• Managers Buttons: Press the button to alert the

Manager from up to 100ft (30m) away from the Kitchen
Controller.

• Grease Pencil : Used to write the staff’s names on the

Magnetic Templates, use a Grease Pencil. One is
supplied with the Kitchen Controller or Cancel/Expeditor
Panel. Using other types of markers may permanently
stain these Panels. Use a soft cloth and rubbing alcohol to
erase Grease Pencil marks.

• Magnetic Templates: Damaged or

scratched templates can be replaced as
needed .

• USB Keyboard: Attach a Keyboard to the

Controller to send a alphanumeric page to
Managers Pagers.

• USB Flash Drive: Use a JTECH USB Flash Drive to

upgrade software and to backup user settings.

Magnetic Templates Grease Pencil Remote Buttons

9

Draft Copy

Antenna Choices to Extend Range

All Extended Range Antenna choices require F CC
approval and licensing. JTECH can assist in
acquiring any additional licensing.

• Magnetic Mount Antenna with 12ft

• 6ft (1.8m) Antenna and 25ft (7.6m)

• Extended Range Antenna Kit:

Extended Range Antenna Kit 6’ (1.8m) Antenna Magnetic Mount Antenna

(3.6m) Cable: All metal indoor/outdoor

Antenna with a magnetized base for
mounting to steel or iron. Wall mounting
hardware include for wall mounting to non
magnetic surfaces.

Cable: Fiberglass indoor/outdoor Antenna
which can mount to any stable
surface. Wall mounting hardware
included.

Includes a 6ft (1.8m) fiberglass indoor/
outdoor Antenna, 35watt Power

Amplifier, Power Supply and 50ft
(15m) or 100ft (30m)Cable. Increase

the output of the Controller to 35 Watts
and range of up to 5 miles (8km).
Requires 110-120VAC outlet and
indoor mounting of the amplifier.

10