JS Automation JD50SHB120 User Manual

SHB120 Series

Intel® Socket 1155 Core™i7 /

Core™i5 / Core™i3 /

Processor PICMG® 1.3 Full-Size

CPU Card

USER’S MANUAL (V1.1)

健昇科技股份有限公司

JS AUTOMATION CORP.

新北市汐止區中興路 100 號 6 樓

6F., No.100, Zhongxing Rd.,

Xizhi Dist., New Taipei City, Taiwan

TEL：+886-2-2647-6936

FAX：+886-2-2647-6940

http://www.automation.com.tw

http://www.automation-js.com/

E-mail：control.cards@automation.com.tw

Correction record

Version

Record

1.1 Add Correction record and Warranty

1

Warranty

The SHB120 series are warranted against defects in materials and workmanship for a period of two years from the date of shipment, as evidenced by receipts or serial no. on board. JS automation Corp. will, at its option, repair or replace product that proves to be defective during the warranty period. This warranty includes parts, labor and shipping costs of returning.

Except as specified herein, JS automation Corp. makes no warranties, express or implied, and specifically disclaims any warranty of merchantability or fitness for a particular purpose. Customer’s right to recover damages caused by fault or negligence on the part of JS automation Corp. shall be limited to the amount theretofore paid by the customer. JS automation Corp. will not be liable for damages resulting from loss of data, profits, use of products, or incidental or consequential damages, even if advised of the possibility thereof. This limitation of the liability of JS automation Corp. will apply regardless of the form of action, whether in contract or tort, including negligence. Any action against JS automation Corp. must be brought within one year after the cause of action accrues. JS automation Corp. shall not be liable for any delay in performance due to causes beyond its reasonable control. The warranty provided herein does not cover damages, defects, malfunctions, or service failures

caused by owner’s failure to follow the JS automation Corp. installation, operation, or maintenance

instructions; owner’s modification of the product; owner’s abuse, misuse, or negligent acts; and power

failure or surges, fire, flood, accident, actions of third parties, or other events outside reasonable control.

If any defect occurs, you should email to us as the following form to get the fast response:

Detailed Company Information

Company/Organization:

Contact Person:

E-mail:

Address:

Country:

Tel/Fax:

Web Site:

Product information

product model:

serial no.:

Environment to Use: such as CPU board, Operating System, target application...

description of defect: (as detail as possible)

3

1. Forward

Thank you for your selection of SHB120 Series cpu card.

Any comment is welcome,

please visit our website:

www.automation.com.tw

for the up to date information.

4

2. Features

 LGA1155 for 3rd Generation Intel® Core™ i7/ i5/ i3 processors (Ivy Bridge)  Intel® Q77 PCH  2 DDR3 DIMM support up to 16 GB memory  Intel® iAMT 8.0 & TPM (optional) supported  PCIe Gen. 3 at 8GT/s supported  USB 3.0 supported  DVI and VGA for dual displays

5

3. Specifications

 CPU :

 Intel® Core™ i3 Desktop Processor  Intel® Core™ i5 Desktop Processor

 Intel® Core™ i7 Desktop Processor  System Chipset : Intel® Q77  CPU Socket : LAG1155 Socket  DRAM Transfer Rate : 1333/1600 MHz  BIOS : AMI BIOS via SPI interface with socket  System Memory

 Two 240-pin DDR3 1333/1600 DIMM sockets

 Maximum up to 16GB DDR3 memory  L1, L2, L3 Cache : integrated in CPU  Onboard Multi-I/O :

 Parallel Port: one 26-pin 2.54-pitch box-header, SPP/EPP/ECP supported

 Serial Port: one for RS-232/422/485 with 10-pin, 2.54-pitch box-header (COM1) and

one port for RS-232 with 10-pin, 2.54-pitch box-header (COM2)

 Floppy controller: one 34-pin, 2.54-pitch box-header supports two drives (1.44MB for

each)

 USB Interface :

 Ten USB ports compliant with USB Spec. Rev. 2.0 (6 ports on board, 4 ports to SHB

connector-C golden fingers)

 Four USB ports compliant with USB Spec. Rev. 3.0 (2 ports on rear I/O, 2 ports on

board)

 Onboard Graphic :

 Intel® Arrandale integrated a Graphic processing unit processor which goes with Q77

chipset with VGA, DisplayPort (co-lay with VGA) and DVI.

 Memory Size : Intel® DVMT 5.0 supported; preallocated memory for frame buffer

option as OS option : Windows XP : * For Total System Memory < 1GB, Graphics sharing memory = 128 MB Maximum; * For 1 GB to 1.5 GB Total System Memory, Graphics sharing memory = 512 MB Maximum; * For 1.5 GB to 2 GB Total System Memory, Graphics sharing memory = 768 MB Maximum; * For 2 GB and Above Total System Memory, Graphics sharing memory = 1GB Maximum. Windows Vista: * Graphics sharing memory max to 0.5* (OS Ram Size – 512)

6

 Resolution -- Analog output -- the analog port utilizes an integrated 400MHz 24-bit

RAMDAC that can directly drive a standard progressive scan analog monitor up to a

resolution of 2048x1536 pixels with 32-bit color at 75 Hz

 Analog Output Interface -- CRT from DAC output via 15-pin D-Sub connector on the

edge; CRT always ON supported

 Ethernet : The LAN1/LAN2 are Intel 82579LM with iAMT 7.0 / Intel 82574L Ethernet

controller support 10/100/1000 Mb/s

 Serial ATA : Two Serial ATA-6Gb/s and Four Serial ATA-3Gb/s performance and

SATA RAID 0/1/5/10 by Q77

 Audio : 10-pin 2.0 pin-header (Intel® HD Audio Digital Header)  Hardware Monitoring : Monitoring temperatures, voltages, and cooling fan status  Watchdog Timer : Reset Supported (1-255 level)  Dimensions : 338mm x 126mm  Expansion interface:

 1 PCI-E x16(Gen.3)  1 PCI-E x4(or 4 PCI-E x1) (Gen.2)  4 PCI

7

4. Dimensions(mm)

8

5. Layout

9

6. Jumper Settings

Jumper

Description

Jumper Setting

JP3

COM1 Mode Selection : RS-232

Short 3-5 , 4-6

JP4

COM1 Mode Selection : RS-232

Short 3-5 , 4-6

JP5

COM1 Mode Selection : RS-232

Short 1-2

JP1

Audio Amplifier Selection : Disable

Short 1-3 , 2-4

JP8

Clear RTC : Normal

Short 1-2

Function

Jumper Setting

JP3

JP4

JP5

RS-232 (Default)

RS-422

RS-485

Function

Jumper Setting

Disable (Default)

Enable

Proper jumper settings configure the SHB120 to meet your application purpose. We are herewith listing a summary table of all jumpers and default settings for onboard devices, respectively.

6.1 COM1 Mode Select Jumpers for RS232/422/485 (JP3, JP4, JP5)

These jumpers select the COM1 port’s communication mode to operate RS-232 or RS-422/485

6.2 Audio Amplifier Jumper (JP1)

10

6.3 Clear RTC Jumper (JP8)

Function

Jumper Setting

Normal (Default)

Clear ME

You may need to use this jumper to clear the RTC if incorrect RTC settings.

11

7. Connectors

Connector

Label

SMBUS

CN1

Floppy Connecter

CN4

Internal USB3.0 Connector port 2/3

CN5

LAN2 External LED

CN6

LAN1 External LED

CN7

USB Port 4/5

CN8

USB Port 6/7

CN10

VGA Port

CN11

Display Port (BOM Option)

CN12

USB Port 8/9

CN13

DVI Connector

CN14

Axiomtek Front Panel

CN15

USB2.0/3.0 Port 1

CN16

Keyboard

CN17

Mouse

CN18

USB2.0/3.0 Port 0

CN19

SYS FAN

FAN1

AUX FAN

FAN2

CPU FAN

FAN3

RJ45 (WG82579LM)

LAN1

RJ45 (WG82574L)

LAN2

Print Connecter

PRINT1

SATA 0 6Gb(SATA3)

SATA1

SATA 1 6Gb(SATA3)

SATA2

SATA Port 2

SATA3

SATA Port 3

SATA4

SATA Port 4

SATA5

SATA Port 5

SATA6

COM1 Connecter

COM1

COM2 Connecter

COM2

Audio Connector

AUDIO1

ATX Connecter

ATX2

Connectors connect this board with other parts of the system. Loose or improper connection might cause problems. Make sure all connectors are properly and firmly connected. Here is a summary table shows you all connectors on the board.

12

7.1 SMBUS Connector (CN1)

Signal

1

CLOCK

2

N.C

3

GND

Signal

1

GND

2

Drive Density Select

3

GND

4

No connector

5

GND

6

No connector

7

GND

8

Index#

9

GND

10

Motor enable A#

11

GND

12

No connector

13

GND

14

Drive select A#

15

GND

16

No connector

17

GND

18

Direction#

19

GND

20

STEP#

21

GND

22

Write data#

23

GND

24

Write gate#

25

GND

26

Track 0 #

27

GND

28

Write protect#

29

No connector

30

Read data#

31

GND

32

Head selection#

33

No connector

34

Disk change#

Connector SMBUS CN1 is for SMBUS interface support.

7.2 Floppy Disk Port Connector (CN4)

The board provides a 34-pin header type connector, CN4, supporting up to two floppy drives. The floppy drives may be any one of the following types: 5.25" 360KB/1.2MB and 3.5" 720KB/1.44MB/2.88MB.

13

7.3 Internal USB Connectors (CN5)

Signal

CN5

1

VBUS0

2

SSRX2-

19

VBUS1

3

SSRX2+

18

SSRX3-

4

GND

17

SSRX3+

5

SSTX2-

16

GND

6

SSTX2+

15

SSTX3-

7

GND

14

SSTX3+

8

USB2-

13

GND

9

USB2+

12

USB3-

10

ID 11

USB3+

Signal

CN8

1

USB_PWR

2

USB_PWR

3

USB4-

4

USB5-

5

USB4+

6

USB5+

7

GND

8

GND

9

GND

10

GND

Signal

1

+ 3.3V

2

LINK_ACT LED(-)

3

100, Low Active

4

+3.3V

5

1000, Low Active

The 19-pin standard Universal Serial Bus (USB 3.0) connectors, CN5 on this board is for installing versatile USB 3.0 interface peripherals.

7.4 Internal USB Connectors (CN8, CN10, CN13)

The 10-pin standard Universal Serial Bus (USB 2.0) connectors, CN8/10/13 on this board are for installing versatile USB interface peripherals.

7.5 LAN2 LED Connectors (CN6)

14

7.6 LAN1 LED Connectors (CN7)

Signal

1

+ 3.3V

2

LINK_ACT LED(-)

3

100, Low Active

4

+3.3V

5

1000, Low Active

Signal

1

Red

2

Green

3

Blue

4

N.C

5

GND

6

DETECT

7

GND

8

GND

9

VCC

10

GND

11

N.C

12

DDC DATA

13

Horizontal Sync

14

Vertical Sync

15

DDC CLK

Signal

1

Data2-

2

Data2+

3

GND

4

N.C.

5

N.C.

6

DDC CLK

7

DDC Data

8

N.C.

9

Data1-

10

Data1+

11

GND

12

N.C.

13

N.C.

14

+5V

15

GND

16

HPD

17

Data0-

18

Data0+

19

GND

20

N.C.

21

N.C.

22

GND

23

Clock+

24

Clock-

7.7 DB15 CRT Connector (CN11) Co-layout with CN12

CN11 is a DB15 connector commonly used for the CRT Monitor.

7.8 DVI-D Pin Header (CN14)

This board supports a 24-pin header (CN14) for DVI-D, via DVI-D cable.

15

7.9 Front Panel Connector (CN15)

Signal

1

Clock

2

DATA

3

No connector

4

GND

5

5VSBY

 Power LED This 3-pin connector denoted as Pin 1 and Pin 5 connects the system power LED indicator to such a switch on the case. Pin 1 is assigned as +, and Pin 5 as -. The Power LED lights up when the system is powered ON. Pin 3 is defined as GND.  External Speaker and Internal Buzzer Connector Pin 2, 4, 6 and 8 can be connected to the case-mounted speaker unit or internal buzzer. While connecting the CPU card to an internal buzzer, please short pins 2-4; while connecting to an external speaker, you need to set pins 2-4 to Open and connect the speaker cable to pin 8 (+) and pin 2 (-).  ATX Power On/Off Button This 2-pin connector denoted as Pin 9 and 10 connects the front panel’s ATX power button to the CPU card, which allows users to control ATX power supply to be power on/off.  System Reset Switch Pin 11 and 12 can be connected to the case-mounted reset switch that reboots your computer instead of turning OFF the power switch. It is a better way to reboot your system for a longer life of the system’s power supply.  HDD Activity LED This connection is linked to hard drive activity LED on the control panel. LED flashes when HDD is being accessed. Pin 13 and 14 connect the hard disk drive to the front panel HDD LED, Pin 13 assigned as -, and Pin 14 as +.

7.10 PS/2 Keyboard, Mouse Connectors (CN17, CN18)

The board provides the Keyboard (CN17) / Mouse (CN18) interface with a 5-pin connecter.

16

7.11 External USB 3.0 Port Connectors (CN16, CN19)

Signal

CN19

1

VCC

2

D-

3

D+

4

GND

5

StdA_SSRX-

6

StdA_SSRX+

7

GND_DRAIN

8

StdA_SSTX-

9

StdA_SSTX+

10

Shield

Signal Name

RS-232

RS-422

RS-485

1

Data Carrier Detect (DCD)

TX-

DATA-

2

Data Set Ready (DSR)

No connector

3

Receive Data (RXD)

TX+

DATA+

4

Request to Send (RTS)

No connector

5

Transmit Data (TXD)

RX+

No connector

6

Clear to Send (CTS)

No connector

7

Data Terminal Ready (DTR)

RX-

No connector

8

Ring Indicator (RI)

No connector

9

Ground (GND)

GND

10

Disconnect(NI)

NI

The 9-pin standard Universal Serial Bus (USB 3.0) port connector on the board is for the installation of peripherals supporting the USB interface.

7.12 RS232/422/485 Pin Assignment (COM1)

The serial interface for the board consists of COM1 support for RS-232 and COM1 for RS-232/RS-422/RS-485.

17

7.13 COM Port RS-232 Pin Assignment (COM2)

Signal

1

Data Carrier Detect (DCD)

2

Data Set Ready (DSR)

3

Receive Data (RXD)

4

Request to Send (RTS)

5

Transmit Data (TXD)

6

Clear to Send (CTS)

7

Data Terminal Ready (DTR)

8

Ring Indicator (RI)

9

Ground (GND)

10

Disconnect(NI)

Signal

1

MIC IN

2

GND

3

LINE_IN_L

4

GND

5

LINE_IN_R

6

GND

7

LINE_OUT_L

8

GND

9

LINE_OUT_R

10

GND

Signal

1

GND

2

GND

3

GND

4

GND

5

+12V

6

+12V

7

+12V

8

+12V

COM2 Serial Port 10-pin (Box-header) Connector Pin Assignment list

7.14 Intel

®

HD Audio Digital Header (AUDIO1)

7.15 ATX 8 Pin 12V IN Connector (ATX2)

You can connect it to the ATX12V power supply for CPU Core Voltage.

18

7.16 A CPU fan is always needed for cooling CPU heat (FAN3)

Signal

1

Ground

2

+12V

3

Rotation Detection

4

Speed Control

Signal

1

GND

2

+12V

3

Rotation Detection

Signal

1

Tx+ (Data transmission positive)

2

Tx- (Data transmission negative)

3

Rx+(Data reception positive)

4

RJ-1(For 1000 base T-Only)

5

RJ-1(For 1000 base T-Only)

6

Rx- (Data reception negative)

7

RJ-1(For 1000 base T-Only)

8

RJ-1(For 1000 base T-Only)

A

Active LED

B

Speed LED

The CPU fan connector FAN3 provides power to the CPU fan.

7.17 System & Auxiliary Fan Connectors (FAN1, FAN2)

You can connect the system cooling fan cable to FAN1/FAN2 for system cooling fan power.

7.18 Ethernet RJ-45 Connectors (LAN1, LAN2)

The RJ-45 connectors LAN1 and LAN2 are for Ethernet. To connect the board to 100-Base-T or 1000-Base-T hub, just plug one end of the cable into LAN1 and connect the other end (phone jack) to a 100-Base-T hub or 1000-Base-T hub.

19

7.19 Parallel Port Connector (PRINT1) Print Port Connector

Signal

1

Strobe#

2

Auto Form Feed#

3

Data 0

4

Error#

5

Data 1

6

Initialize#

7

Data 2

8

Printer Select In#

9

Data 3

10

GND

11

Data 4

12

GND

13

Data 5

14

GND

15

Data 6

16

GND

17

Data 7

18

GND

19

Acknowledge#

20

GND

21

Busy

22

GND

23

Paper Empty#

24

GND

25

Printer Select

26

N.C

This board has a multi-mode parallel port to support: Standard Mode:

-directional parallel port.

Enhanced Mode: Enhance parallel port (EPP) is compatible with EPP 1.7 and EPP 1.9 (IEEE 1284 compliant). High Speed Mode: Microsoft and Hewlett Packard extended capabilities port (ECP) is IEEE 1284 compliant.

20

7.20 SATA Connectors

Signal

1

GND

2

SATA_TX+

3

SATA_TX-

4

GND

5

SATA_RX-

6

SATA_RX+

7

GND

(SATA1(3.0) ,SATA2(3.0),SATA3,SATA4,SATA5,SATA6) These SATA connectors are for high-speed SATA interface ports and they can be connected to hard disk devices.

21

8. Ordering Information

PRODUCT

DESCRIPTIONS

JD50SHB120

SHB120 LGA1155 Intel® Core™ i7/ i5/ i3 PICMG 1. 3 Full-size CPU Card with Intel® Q77 PCH, SATA3, USB 3.0, VGA/DVI and Dual LANs

22

JS Automation JD50SHB120 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Correction record

CONTENTS

Warranty

1. Forward

2. Features

3. Specifications

4. Dimensions(mm)

5. Layout

6. Jumper Settings

6.1 COM1 Mode Select Jumpers for RS232/422/485 (JP3, JP4, JP5)

6.2 Audio Amplifier Jumper (JP1)

6.3 Clear RTC Jumper (JP8)

7. Connectors

7.1 SMBUS Connector (CN1)

7.2 Floppy Disk Port Connector (CN4)

7.3 Internal USB Connectors (CN5)

7.4 Internal USB Connectors (CN8, CN10, CN13)

7.5 LAN2 LED Connectors (CN6)

7.6 LAN1 LED Connectors (CN7)

7.7 DB15 CRT Connector (CN11) Co-layout with CN12

7.8 DVI-D Pin Header (CN14)

7.9 Front Panel Connector (CN15)

7.10 PS/2 Keyboard, Mouse Connectors (CN17, CN18)

7.11 External USB 3.0 Port Connectors (CN16, CN19)

7.12 RS232/422/485 Pin Assignment (COM1)

7.13 COM Port RS-232 Pin Assignment (COM2)

7.15 ATX 8 Pin 12V IN Connector (ATX2)

7.16 A CPU fan is always needed for cooling CPU heat (FAN3)

7.17 System & Auxiliary Fan Connectors (FAN1, FAN2)

7.18 Ethernet RJ-45 Connectors (LAN1, LAN2)

7.19 Parallel Port Connector (PRINT1) Print Port Connector

7.20 SATA Connectors

8. Ordering Information