NSVS1203 Mar. 2007
Application
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Maximum Rating: (Table 2)
Mechanical Specifications: (Fig.2)
Package is designed as small as 2.0x1.6x0.65[mm
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
1575.42MHz GPS
Table 1. Electrical Specifications
Item Spec. Typical
Input and Output Impedance Nominal Center Frequency (f0) - 1575.42MHz
Insertion Loss 1574.42~1576.42MHz 3.5dB max. 2.8dB
Response Variation 1574.42~1576.42MHz 1.5dB max. 0.5dB
Input and Output VSWR 1574.42~1576.42MHz 2.5 max. 2.0
Out of Band Rejection
(Relative to
Through Level)
Table 2. Maximum Ratings
Item Rating
Maximum Input Power +10dBm
Maximum DC Voltage 7.5V
Operating Temperature Range -40~+85ºC
Storage Temperature -40~+95ºC
http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese)
JRC SAW FILTER
NSVS1203
1475.42MHz 35dB min. 48dB
1535.42MHz 30dB min. 45dB
1615.42MHz 30dB min. 35dB
1675.42MHz 40dB min. 50dB
(Operating Temperature Range: -40~+85ºC)
3
] for SMD (Surface Mount Device) type.
Sales and Marketing
Communications Equipment Business Department
10-1, Nishi-Shinjuku 6-chome, Shinjuku-ku,
Tokyo, 160-8328 Japan
Tel. +81 3-3348-3845
Fax. +81 3-3348-3935
http://www.jrc.co.jp/eng/product/saw/index.html (English)
50Ω
NSVS1203 Mar. 2007
IN
50Ω
1
2
4
SAW
3
OUT
50Ω
Fig.1 Measuring circuit
2. 0±0. 1
1. 6± 0. 1
･FQ
(1)
(2)
(3)
0. 70 Max.
2
3
4-
0. 5 0 ± 0. 1 0
1
4-
0. 55 ± 0. 1 0
4
8-
(0.075)
Fig.2 Package dimensions (in mm)
2. 20
Marking
(1) Index Mark
(2) Part Number Mark
(3) Lot Number
Shown in Table.3
Pin no. Connection
1 GND
2 IN
3 GND
4 OUT
1. 8 0
4- 0 .60
Fig.3 Desirable land area (in mm)
4- 0. 65
Table.3 Lot Number Code（Year/Month）
Month
Year
1 2 3 4 5 6 7 8 9 10 11 12
2006 A B C D E F G H J K L M
2007 N P Q R S T U V W X Y Z
2008 a b c d e f g h j k i m
2009 n p q r s t u v w x y z
Recur every 4 years
NSVS1203 Mar. 2007
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -40ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact Japan Radio Company before proceeding with the
design of equipment incorporating this product.
3. The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please contact
our sales representatives in advance.
NSVS1203 Mar. 2007
Fig.1 Measuring circuit
(R0.3)
[4
×]
(1.4)
(0.8 )
[12×]
Pin No. Connection
1GND(PKG)
2GND(PKG)
3 GND(PKG)
4GND(PKG)
5OUT/IN
6 GND(signal)
7GND(PKG)
8GND(PKG)
9GND(PKG)
10 GND(PKG )
11 IN/OUT
12 GND(signal)
(b)
(3)
Marking
(1) Manufacture's Mark
(2) Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(c) Date
1-9 --- 0
10 -19--- 1
20 -31--- 2
(3) Part Number Mark
(1.26± 0.1 3)
[12× ]
[12× ]
(2.5 4 )
(R0.3)
(2)
4
5
6
7
8
910
(C)
１２３４
10
９８７
11
12
６
５
OUT
50O
SAW
*27nH
*27nH
39pF
33pF
*murata LQW18A series
S21
0
FREQUENCY CHARACTERISTICS
0
Insertion Loss [dB]
11 11
9 9
7 7
5 5
VSWR
3 3
1 1
InsertionLoss [dB]
10
20
30
40
50
2
4
6
8
10
CH1 : center 1575.42 span 200
CH2 : center 1575.42 span 200
S11 S22
S11 S22
1475.4 1475.4 1675.4 1675.4
S21
0
20
40
60
80
100
0 3000
Frequency [MHz] Frequency [MHz]
Frequency [MHz]
VSWR
Insertion Loss [dB]
Japan Radio Co.,Ltd.
Loading...