JRC NSVS1123 User Manual

Application
Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1.
243.95MHz PHS 1st IF
JRC SAW FILTER
NSVS1123
Table 1. Electrical Specifications Item Nominal Center Frequency (f0) 3dB Band Width Insertion Loss at f0 Ripple f0±100kHz Group Delay Time Ripple f0±100kHz
243.95MHz -
260kHz min. -
3.5dB max. 3.0dB
1.0dB max. 0.40dB
1.0us max. 0.40us
--
Out of Band Rejection
(Relative to Through Level)
f0±600kHz 25dB min. 30dB f0±10.7MHz 40dB min. 60dB f0±21.4MHz 60dB min. 65dB
NSVS1123 Jul. 2005
(Operating Temperature Range: -10~+60℃)
Maximum Rating: (Table 2)
Mechanical Specifications: (Fig.2) Package is designed as small as 3.0x3.0x1.15[mm
Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling.
Table 2. Maximum Ratings Item Rating Maximum Input Power +5dBm Operating Temperature Range -10~+60ºC Storage Temperature -40~+85ºC
3
] for SMD (Surface Mount Device) type.
Communications Equipment Division
Communications Equipment Marketing Department
10-1, Nishi-Shinjuku 6-chome, Shinjuku-ku,
Tokyo, 160-8328 Japan
Tel. +81 3-3348-3845
Fax. +81 3-3348-3935
http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese)
http://www.jrc.co.jp/eng/product/saw/index.html (English)
NSVS1123 Jul. 2005
IN50
1.15±0.15
(R0.15)
(1.27)(1.27)
(R0.15)
[4x]
(a)
110nH
2.0pF
1 2
S A W
3
Fig.1 Measuring Circuit
3.00±0.15
6 5 4
571
3.00±0.15
S6
(2)
(3.0)
(0.3)
(0.6)
[4x]
(1.8)
(0.45)
Fig.2 Package Dimensions (in mm)
3.8
0.93
2.2
0.6
3.8
1.15
0.93
Fig.3 Desirable land area (in mm)
(0.25)
(0.75)
[6x]
1.15
110nH
2.0pF
(b)
(c)
(1)
(R0.30)
[4x]
(0.6)
(0.53)
OUT
50
[2x]
[4x]
Marking (1) Lot Number (a) Year (b) Month *Oct.--- X Nov.--- Y Dec.--- Z (c) Date
(2) Part Number Mark
Pin no. Connection
1 - 9 --- 0
10 -19 --- 1 20 -31 --- 2
1 GND 2 IN 3 GND 4 GND 5 OUT 6 GND
NSVS1123 Jul. 2005
Notice
1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than –10ºC or more than +60ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand.
Note
1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is therefore advisable to contact Japan Radio Company before proceeding with the design of equipment incorporating this product.
Loading...