Application
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
1227.6MHz GPS L2
Table 1. Electrical Specifications
Item Spec. Typ.
Input and Output Impedance Nominal Center Frequency (f0) - 1227.6MHz
Insertion Loss 1217.6~1237.6MHz 3.5dB max. 2.8dB
Response Variation 1217.6~1237.6MHz 1.5dB max. 1.0dB
Input and Output VSWR 1217.6~1237.6MHz 2.0 max. 1.5
Out of Band Rejection
(Relative to
Through Level)
JRC SAW FILTER
NSVS1108
DC~1088MHz 40dB min. 45dB
1088~1178MHz 35dB min. 40dB
1178~1193MHz 17dB min. 42dB
1263~1278MHz 18dB min. 45dB
1278~1368MHz 30dB min. 38dB
1368~1785MHz 35dB min. 40dB
1785~2500MHz 27dB min. 35dB
2500~4000MHz 20dB min. 30dB
NSVS1108 Oct. 2004
50Ω
(Operating Temperature Range : -30~+85ºC)
Maximum Rating: (Table 2)
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
Table2. Maximum Ratings
Item Rating
Maximum Input Power +20dBm
Maximum DC Voltage 7.5V
Operating Temperature Range -30~+85ºC
Storage Temperature -40~+90ºC
3
] for SMD (Surface Mount Device) type.
Communications Equipment Division
Communications Equipment Marketing Department
10-1, Nishi-Shinjuku 6-chome, Shinjuku-ku,
Tokyo, 160-8328 Japan
Tel. +81 3-3348-3845
Fax. +81 3-3348-3935
http://www.jrc.co.jp/jp/product/device/saw/index.html(Japanese)
http://www.jrc.co.jp/eng/product/saw/index.html(English)
NSVS1108 Oct. 2004
A
IN
50Ω
1
2
34
SAW
6
5
OUT
50Ω
(a)
Fig.1 Measuring circuit
3. 0±0. 15
(b)
3. 0± 0. 1 5
4X2
(c)
(1)
G
(2)
Marking
(1) Lot Number
1. 15±0. 15
(0.6)
(0.25)
3
2
(1.80)
4
[2x]
(0.6)
5
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(c) Date
*1-9--- 0
10-19--- 1
20-31--- 2
(2) Part Number Mark
1
(0.45)
Fig.2 Package dimensions (in mm)
3.8
0.93
(0. 75)
[4x]
6
[4x]
(0.53)
Pin no. Connection
1 GND
2 IN/OUT
3 GND
4 GND
5 OUT/IN
6 GND
2.2
1.15
0.6
3.8
1.15
0.93
Fig.3 Desirable land area (in mm)
NSVS1108 Oct. 2004
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -30ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact Japan Radio Company before proceeding with the
design of equipment incorporating this product.
3. The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please
contact our sales representatives in advance.
NSVS1108 Oct. 2004
Fig.1 Measuring circuit
(R0.3)
[4
×]
(1.4)
(0.8 )
[12×]
Pin No. Connection
1GND(PKG)
2GND(PKG)
3 G ND(PKG)
4GND(PKG)
5OUT/IN
6 GND(signal)
7GND(PKG)
8GND(PKG)
9GND(PKG)
10 GND(PKG)
11 IN/OUT
12 G ND(signal)
(b)
(3)
Marking
(1) Manufacture's Mark
(2) Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(c) Date
1-9--- 0
10 -19--- 1
20 -31--- 2
(3) Part Number Mark
(1.26± 0.1 3)
[12× ]
[12× ]
(2.5 4 )
(R0.3)
(2)
4
5
6
7
8
910
(C)
１２３４
10
９８７
11
12
６
５
OUT
50O
SAW
*27nH
*27nH
39pF
33pF
*murata LQW18A series
0
10
20
30
S21
FREQUENCY CHARACTERISTICS
1
2
1
2
1 : 1217.599 [MHz] 2.67 [dB]
1 : 1217.599 [MHz] 2.67 [dB]
2 : 1237.599 [MHz] 2.47 [dB]
2 : 1237.599 [MHz] 2.47 [dB]
0
2
4
6
40
Insertion Loss [dB]
50
8
10
Insertion Loss [dB]
CH1 : center 1227.6 span 200
CH2 : center 1227.6 span 200
S11 S22
S11 S22
11 11
9 9
7 7
5 5
VSWR
3 3
1 1
1127.6 1127.6 1327.6 1327.6
S21
0
20
40
60
80
InsertionLoss [dB]
100
0 3000
Frequency [MHz] Frequency [MHz]
1
2
1
2
1
2
VSWR
1
2
Frequency [MHz]
Japan Radio Co.,Ltd.
Loading...