NSVS1061 Jan. 2005
JRC SAW FILTER
NSVS1061
Application
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Mechanical Specifications:
Package is designed as small as 9.1x4.8x1.3[mm
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
174MHz GPS
Table 1. Electrical Specifications
Parameter Spec. Typ.
Input and Output Impedance Nominal Center Frequency (f0) - 174 MHz
3dB Bandwidth - 22 MHz
Insertion Loss 163.0~185.0MHz 12.0 dB 10.0 dB
Response Variation 163.0~185.0MHz 1.5 dB 1.0 dB
Group Delay Variation 163.0~185.0MHz 150 ns 100 ns
Out of Band Rejection
149~157MHz
191~199MHz
30 dB
30 dB
(Operating Temperature Range: -20~+70ºC)
Maximum Rating: (Table 2)
Table2. Maximum Ratings
Item Rating
Maximum Input Power +10dBm
Maximum DC Voltage 7.5V
Operating Temperature Range -20~+70ºC
Storage Temperature -30~+80ºC
3
] for SMD (Surface Mount Device) type.
Communications Equipment Division
Communications Equipment Marketing Department
10-1,Nishi-Shinjuku 6-chome Shinjuku-ku,
Tokyo. 160-8328 Japan
Tel. +81 3-3348-3845
Fax. +81 3-3348-3935
http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese)
http://www.jrc.co.jp/eng/product/saw/index .html (English)
50Ω
40 dB
30 dB
IN
50O
876
9
*20nH
SAW
10
12 3
Fig.1 Measuring circuit
5
120pF
4
*20nH
*murata LQW18A series
OUT
50O
NSVS1061 Jan. 2005
(1)
4.8±0.15
1.3 max.
(0.65)
9.10 ±0.15
①
②
③
Ｊ４５１
１０６１
(3)
(2.54)
(R0.15)
[10× ]
(2.54)
(1.15）
(2)
(R0.2)
[4×]
Marking
(1)Manufacture's Mark
(2)Lot Number
①Year
②Month *Oct.‑‑‑X
Nov.‑‑‑Y
Dec.‑‑‑Z
③Day 1‑9 ‑‑‑0
10‑19‑‑‑1
20‑31‑‑‑2
(3)Part Number Mark
(2.54)
１
２
３
10
９
８
７
６
Fig.2 Package dimensions(in mm)
(1.0)
[10×]
４
５
(R0.2)
[10× ]
[10×]
(0.8)
No. Connection
1 GND(PKG)
2 GND(PKG)
3 GND(PKG)
4 OUT/IN
5 GND(signal)
6 GND(PKG)
7 GND(PKG)
8 GND(PKG)
9 IN/OUT
10 GND(signal)
NSVS1061 Jan. 2005
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -20ºC or more than +70ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When solde ring iron is used, solder with the temperature at the tip of so ldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply st atic electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact Japan Radio Company before proceeding with
the design of equipment incorporating this product.
3. The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please
contact our sales representatives in advance.
FREQUENCY CHARACTERISTICS
NSVS1061 Jan. 2005
10
20
30
40
50
Insertion Loss [dB ]
60
1000
900
154 164 174 184 194
Frequency [MHz]
6
8
10
12
14
16
Group Delay [ns]
800
700
600
500
S11
162 168 174 180 186
Frequency [M H z]
S22
Loading...