User
Manual
ExplorAir Magic Air
1
WARNING
DO NOT USE THIS PRODUCT UNLESS YOU HAVE READ AND UNDERSTAND THESE WARNINGS
AND INSTRUCTIONS WHICH ARE FOR YOUR SAFETY AND PROTECTION. THIS INFORMATION
MAY BE SUBJECT TO CHANGE AT ANY TIME. PLEASE VISIT OUR WEBSITE AT: www.jpaustralia.com FOR CURRENT UPDATES.
IF YOU ARE BELOW THE AGE OF 18, YOU SHOULD HAVE YOUR PARENT OR GUARDIAN READ
THESE WARNINGS AND INSTRUCTIONS AND SHOULD NOT USE THIS PRODUCT UNLESS YOU
ARE UNDER THE PROPER GUIDANCE AND SUPERVISION OF SUCH A PERSON.
Familiarize yourself with this inatable board before using it on the water in order to ensure safety and to
prevent accidents.
The use of this product exposes the user to many unavoidable and unexpected risks,
HAZARDS
injury caused by any use, misuse, abuse or irresponsible use of this product by the user.
. The suppliers of this product are not responsible for any damage to property or any personal
RECOMMENDED WINDSURF PRACTICE:
• Windsurng is a HAZARDOUS activity and the use of windsurng equipment involves the risk of serious
personal injury to any part of the user’s body or death.
DANGERS
and
• Do NOT exceed the recommended pressure of 15 psi/1bar and do NOT leave the board in the sun
when not in use.
• Injuries are an INHERENT RISK of windsurng and the participation in windsurng implies the user’s
acceptance of those risks.
• Wear a helmet when appropriate.
• Children should always be under adult supervision.
• It is strongly recommended that beginners take lessons from a licensed or certied instructor.
• Always inspect your equipment for signs of wear and tear each time before sailing.
• IF any product is found to show signs of wear & tear this should be repaired or replaced immediately
and before further use. If in doubt about any signs of wear & tear, please contact your local JP-Australia
Dealer and/or distributor.
• Make sure that your n screw and the foot straps are tightened rmly.
• Make sure that your rig is connected to your board rmly.
• NEVER place yourself in a situation where breakage of any one of the various windsurng components
would pose a risk to yourself or others, or make it impossible to return to the shore safely & unassisted.
• Take time to study the conditions including sea state, tides, currents and weather forecasts before you
decide to go sailing. Beware of sailing in offshore winds.
• Familiarize yourself with any new location before venturing onto the water. Ask the locals to tell you about
any hazards.
• Watch out for other beach users, especially swimmers, divers and small children. Make sure you keep
your board and rig under control at all times and that they don’t get blown about on the beach or in the
water.
•
Always use appropriate safety and oatation devices. Wear the correct protective clothing for the conditions
such as a wetsuit or a UV top. Cold water and cold weather can result in hypothermia. Always carry identication.
3
• Make sure someone knows where you’ve gone & when you are expected back – never sail alone.
• Be aware of the conditions as they change. Always return to the beach if there is a signicant change in
the conditions, i.e. wind dropping or wind & waves increasing.
• As you learn the sport, work within your own limitations and do not exceed them.
• Make sure to stay hydrated. Windsurng is a physically demanding sport and dehydration can also occur
in cold temperatures.
• Do not alter, modify or change this product.
• This product is designed and manufactured only for windsurng on water.
• Do not exceed maximum weight capacity. Regardless of the number of persons on board, the total
weight of persons and equipment must not exceed maximum weight capacity.
• Do not operate the board under the inuence of drugs or alcohol.
• Keep these instructions for future reference.
Features
Stringer
Mast plug
EVA Pad
Handle
(ExplorAir only)
Valve
D-Ring
Stringer
Model Actual volume Capacity
Name (L) (kg)
MagicAir 150 200 100
ExplorAir 200 240 130
Fin 10”
+ screw
+ plate
Center n box
(As an accessorie part for MagicAir)
Fin Ride 44
+ assembly
set
Hard rail
Removable
Footstraps
4
Safety guide
Special fully integrated box for Powerbox ns
Instructions to inate your board:
1 - Carefully roll out
the board
3
- Connect the
pump hose to the
valve, insert and
rotate it to the
right
4 - Keep
your feet
rmly on
the foot
rests
and start
pumping
2 - Pull the valve pin
counter-clockwise
and up
5 - Turn from
double action
to single action
when it is
difcult to pump
Warning
Any use of an air compressor may
result in poor performance or damage
to the board, and automatically avoids
all warranties. If you leave your board
exposed to the hot sun, check the
pressure and deate it slightly. Otherwise
the board may become over inated
and stretch the material. The ambient
temperature affects the tube’s internal
pressure: a variation of 1°C/ 1.8°F
causes a variation of the pressure in the
tube of +/- 4 mBar (0.06psi).
6 - Pump your
board to 15 psi
(1 bar)
5
Inserting the ns:
Fin Ride 44 Center n
(Only comes with ExplorAir)
1 - Insert the
n into the
nbox, minding
the correct
position.
1 - Insert the
plate into the
nbox
2 - Insert the assembly set
(screw and washers) inside
the hole located on the tail
of deck. Then tighten the
screw.
2 - Push the plate
towards the front
edge of the nbox
3
- Insert the pin of the n
into the nbox cavity and
push the n into the nbox
6
6
4 - Push the n into the nbox
and tighten the screw
Inserting the footstraps:
1 - Position
footstrap next
to D-Ring
3 - Take the two inside
parts and put them thru
the D-Rings (left side
closed/right side open)
4 - Place the left inside
part into the inside of the
right part and close it
2 - Open footstrap
and remove EVA cover
5 - Put the EVA cover around the inside parts and close the
footstrap (adjust the size of the inside parts if needed)
7
7
Deating the board:
Whenever you take your board out of the water and deate
it, allow time for it to air out and dry. Neither the skin/hull
nor the inside chambers will suffer from water damage, but
stagnant water could cause mildew and foul odor.
1
- Push
the valve pin
clockwise and
down
2 - After deation,
roll up the board from
the tail part
HOW TO REPAIR SMALL PUNCTURES
Make sure that the board is fully deated and lies at.
1. Prepare a round patch no less than 3 inches or 7
centimeters in diameter.
2. Clean the patch and the area surrounding the leak with
alcohol.
3. To contain excess glue, use masking tape to tape off the
area around the patch.
4. Apply 3 thin, even coats of repair kit adhesive to both the
surface of the board and the patch. Wait 5 minutes between
each coat.
5. After the 3rd coat, wait 10-15 minutes before applying
the patch. Use a hand roller to apply the patch evenly. Pay
special attention to the edges.
6. Wait 24 hours before re-inating.
• Perform all of your repairs in a well-ventilated area.
• Avoid inhaling glue vapors.
• Avoid contact with the skin or the eyes.
• Keep all repair materials (glue, solvents, etc.) away from
the reach of children.
• The repairs on the welds must not be glued. Only the
manufacturer of the board can perform repairs on the welds
themselves.
3 - Store the board
into the bag for
protection
8
8
MAINTENANCE
1. Clean and check the board as well as all the accessories.
Make sure the board is completely dry before putting it
away. Make sure that neither sand nor gravel remains inside
the board or between the hull and the inner chambers: this
could result in abrasion or even punctures while storing the
board.
2. When storing your inatable, keep it in a clean and dry
place.
How to attach accessory Center n box (Magic Air):
Items included:
• US n box
• PVC patch
• Fin 10”
• Glue
1 - Attach the nbox and the PVC patch
onto the marked area on the board –
following the instructions on the adhesive
tube.
9
JP-AUSTRALIA – LIMITED WARRANTY
Every JP-Australia product is subjected to rigid pre-sales quality control tests and is backed by our comprehensive warranty policy
below.
JP-Australia warrants that this product, when it is purchased from an authorized JP-Australia dealer by a retail customer, will be free
from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original retail customer. This
warranty is solely for the benet of the original retail purchaser and may not be assigned.
For customer Limited Warranty claims, proof of purchase from an authorized JP-Australia dealer is required. If the date of purchase
cannot be established, JP-Australia will make a determination based upon on the last production year of the particular model, or on
the condition of the equipment claimed.
If you have any questions about the JP-Australia Limited Warranty or procedures for making claims thereunder, please contact
your local JP-Australia dealer or JP-Australia at www.jp-australia.com. The JP-Australia Warranty Center will determine if a product
is covered under this Limited Warranty. If covered, JP-Australia will, at JP-Australia’s sole option, repair or replace the product in
question.
All returns must be made through JP-Australia authorized dealers. JP-Australia does not accept returns directly from customers.
Any repair or replacement of any product under this Limited Warranty is not available for ordinary wear and tear, including scratches,
punctures, fading and print chipping, or for any damage caused by misuse, abuse, unauthorized modication or repairs, usage
of components other than JP-Australia components, accident, heat, excessive exposure to sunlight, improper handling, storage,
maintenance or care; incorrect setup, use in commercial, rental or teaching environments; any use of the product outside the
recommended conditions as listed on the JP-Australia website: www.jp-australia.com; use off the water; any blow or impact with a
hard or spikey object or any other irresponsible use.
THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OF QUALITY AND PERFORMANCE,
WRITTEN, ORAL OR IMPLIED AND ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. IN NO EVENT SHALL JP-AUSTRALIA BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL, STATUTORY OR EXEMPLARY DAMAGES, WHETHER IN CONTRACT, TORT,
NEGLIGENCE, STRICT LIABILITY OR OTHERWISE including, without limitation, loss to property other than this product, loss of use of
said product, or other property or other economic losses. JP-Australia shall not be liable for contribution or indemnication, whatever
the cause.
Some jurisdictions do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of incidental or
consequential damages, so the above limitation and exclusion may not apply to particular customers. JP-Australia obligations under
any warranty shall be limited, to the greatest extent allowed by law, as provided in this JP-Australia Limited Warranty. This Limited
Warranty gives you specic legal rights; you may also have other rights, which vary from one jurisdiction to another.
10
11
12
Photos: Marko Butrakovic / Robby Swift
Loading...