JOYTECH PY500AC, PY500ACU User Manual

Sliding Gate Operator

User's Manual

PY

PY

PY

PY 5

5

5

5 00

00

00

00 A

A

A

A C

C

C

C

PY500AC SLIDING GATE OPERATOR

1

OUTLINE

1. Products introduction …………………………………… 2

2. Important safety precautions …………………………… 2

3. Main technical parameters …………………………… 2

4. Mechanical Installation ………………………………… 2

5. Adjustment ……………………………………………… 5

6. Wire Connecting ………………………………………… 6

7. Turning and operation …………………………………… 8

8. Programming Process …………………………………… 10

9. Maintenance …………………………………………… 1 1

10. Trouble Shooting ………………………………………… 1 1

1 1 . Packing list …………………………………………… 1 1

PY500AC SLIDING GATE OPERATOR

2

1.

1.

1.

1. Products

Products

Products

Products introduction

introduction

introduction

introduction

please

please

please

please read

read

read

read the

the

the

the instructions

instructions

instructions

instructions carefully

carefully

carefully

carefully before

before

before

before proceeding.

proceeding.

proceeding.

proceeding.

MCU

MCU

MCU

MCU is

is

is

is supplied

supplied

supplied

supplied to

to

to

to control

control

control

control the

the

the

the gate

gate

gate

gate operator.

operator.

operator.

operator.

Keypad

Keypad

Keypad

Keypad /

/

/

/ single

single

single

single button

button

button

button interface.

interface.

interface.

interface.

P

P

P

P hoto

hoto

hoto

hoto beam

beam

beam

beam safety

safety

safety

safety beam

beam

beam

beam interface.

interface.

interface.

interface.

User

User

User

User can

can

can

can select

select

select

select Auto-close

Auto-close

Auto-close

Auto-close function.

function.

function.

function.

Manual

Manual

Manual

Manual key

key

key

key release

release

release

release design

design

design

design for

for

for

for emergency

emergency

emergency

emergency purposes.

purposes.

purposes.

purposes.

2.

2.

2.

2. Important

Important

Important

Important safety

safety

safety

safety information

information

information

information

Carefully read and follow all safety precaution s and warning before attempting to install and use this

automatic gate operator.

Make

Make

Make

Make sure

sure

sure

sure the

the

the

the Power

Power

Power

Power supply(AC220V

supply(AC220V

supply(AC220V

supply(AC220V or

or

or

or AC110V)

AC110V)

AC110V)

AC110V) of

of

of

of the

the

the

the gate

gate

gate

gate operator

operator

operator

operator is

is

is

is suitable

suitable

suitable

suitable for

for

for

for the

the

the

the power

power

power

power

supply

supply

supply

supply in

in

in

in your

your

your

your area.

area.

area.

area.

3.

3.

3.

3. Main

Main

Main

Main technical

technical

technical

technical parameters

parameters

parameters

parameters

Type PY500AC PY500ACU

Power supply 220V , 50Hz

11 0V

, 6 0Hz

Motor speed 42rpm 47rpm

Rated output power of motor 150W

Remote control o perating distance 30m (F requency: 433.92 mHz)

Remote control mode Single button

Output shaft height 58.5mm

Max. gate weight 500Kg

Output torque 1 4 N · m

Limit switch Spring limit switch

Noise ≤ 60 dB

Duty cycle S 2, 15 minutes

extra remote control

20

Environmental temperature - 2 0 ° C~ + 5 0 ° C

Gate Move speed

12m/min

4.

4.

4.

4. Mechanical

Mechanical

Mechanical

Mechanical Installation

Installation

Installation

Installation

The PY500AC will handle gate weighting up to 500kg and up to 12m if the proper installation procedures

have been followed .

The PY500AC g ate o pe rator operates by forcing a drive rack by a drive gear. The entire configuration is

shown in the diagram below . The gate operator must be installed on the inside of the gate.

PY500AC SLIDING GATE OPERATOR

3

Sliding gate

Gate operator

Rack

Switch

Input power

Wall

Fig.1

Gate preparation

Be sure the gate is properly installed and slides smoothly before installing the PY500AC sliding gate

operator. The gate must be plumb, level, and move freely.

Conduit

In order to protect the cable , use PVC conduit for low voltage power cable and control wires. Conduit

must be pre set into the concrete when it is poured. Wires within the conduit shall be located or protected

so that no damage can result from contact with any rough or sharp part.

Concrete p ad

The base unit of the gate operator requires a concrete pad in order to maintain proper stability. The

concrete pad should be approximately 400 mm x 250 mm x 200 mm deep in order to provide for adequate

weight and structure to insure proper stable installation.

Anchors (see Fig.2)

You can use anchor bolts, anchors, washers and nuts. These anchors must be set into the concrete when

it is poured or y ou can use wedge anchors to fasten the operator.