Joy-it robot05 User guide

Robot Kit 05
for Arduino
3
Robot Kit 05
Published: 13.08.2018 Copyright by Joy-IT 2
1. Introduction
2. Overview
3. Assembly
4. Safety notices
5. Information and take-back obligations
6. EU-Declaration of conformity
7. Support
INHALTSVERZEICHNIS
Robot Kit 05
Published: 13.08.2018 Copyright by Joy-IT 3
Dear customer, thank you for choosing our product. In the following, we will show you what to observe during commissioning and use. Should you encounter any unexpected problems during use, please do not hesitate to contact us.
The Robot Kit 05 is a kit that can be used as a basic framework for a car / robot. You have
to add other components such as a power source (battery, batteries) and a controller such as an Arduino with motor controller. We recommend the use of JOY -iT accessories.
The base plate already contains the holes for mounting an Arduino. The motors are designed for a voltage of 3-9 V DC (4.5V recommended).
1. INTRODUCTION
2. OVERVIEW
Voltage DC V 4,5 6 7,2 9 Current at idle mA 190 160 180 200 Speed per minute at idle +- 10% 90 190 230 300 Torque gf/cm min. 800 800 1000 1200
Robot Kit 05
Published: 13.08.2018 Copyright by Joy-IT 4
Included materials:
Baseplate (1x)
Engine mount (4x)
DC Motors (2x)
Wheel (2x)
Perforated Wheel (2x)
Spacers (4x)
Screw 3x30 (4x)
Screw 3x8 (10x)
M4 Nut (10x)
Dolly (1x)
Switch (1x)
Baery Case (1x)
Robot Kit 05
Published: 13.08.2018 Copyright by Joy-IT 5
3. ASSEMBLY
Insert the motor mounngs and the toggle
switch into the base plate aer removing the yellow protecve foil.
The axis hole of the pinion has a wide and a narrow side. The width side should point in the direcon of the motor.
Mount the hole wheel on the motors and the­se on the brackets.
Robot Kit 05
Published: 13.08.2018 Copyright by Joy-IT 6
Tighten the motors.
Aach the baery container.
Insert the spacers and fasten the dolly. The assembly is now completed.
Robot Kit 05
Published: 13.08.2018 Copyright by Joy-IT 7
The device must not be unaended during operaon. Disconnect the power supply or remove the power source ( e.g. baeries) when not in use. The device is not a toy, it contains swallowable small parts and is not suitable for children.
Acrylic sheets can break under overload. The motors must not be blocked or overloaded, this can lead to strong heat development. The motors can generate heat during operaon, let the motors cool down before touching them. The kit is intended for use in dry rooms, it must not get wet or damp. Strong sunlight should be avoided. Please also observe the safety instrucons for the addional components you have installed. There is a parcular risk of burns when soldering.
Symbol on electrical and electronic equipment
This crossed-out dustbin means that electrical and electronic equipment does not belong in household waste. You must return the old devices to a collection point. Before disposal, you must separate old batteries and accumulators which are not enclosed in the old device from it.
Return options
As an end user, you can dispose of your old device (which essentially fulfils the same function as the new one purchased from us) free of charge when purchasing a new device. Small appliances where no external dimensions are larger than 25 cm can be delivered in
normal household quantities, irrespective of the purchase of a new appliance.
Possibility of return at our company location during opening hours
Simac GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn
Possibility of return in your area
We will send you a parcel stamp with which you can return the device to us free of charge. Please contact us by e-mail at Service@joy-it.net or by phone.
Information about packaging
If you do not have suitable packaging material or do not wish to use your own, please contact us and we will send you suitable packaging.
4. SICHERHEITSHINWEISE
5. INFORMATIONS- UND RÜCKNAHMEPFLICHTEN
Robot Kit 05
Published: 13.08.2018 Copyright by Joy-IT 8
As manufacturer we, Simac GmbH, declare that our product Robot05 fulfils the basic requirements of the following guidelines when used as intended:
RED Directive 2014/53/EU RoHS Directive 2011/65/EU
You can request the detailed declaration of conformity from us at the following address:
Simac GmbH , Pascalstr. 8, 47506 Neukirchen-Vluyn
23.05.2017 Xu Lu chief executive officer
Attention, this declaration of conformity only applies to the kit components supplied by us, the motors supplied by us comply with the regulations of the EMC directive when operated with the specified voltage. By adding your own components, you yourself become the manufacturer and must therefore also ensure that the resulting the resulting device complies with the regulations.
6. EU-DECLARATION OF CONFORMITY
Robot Kit 05
Published: 13.08.2018 Copyright by Joy-IT 9
7. SUPPORT
We also support you after your purchase. If there are any questions left or if you encounter any problems, please feel free to contact us by mail, phone or by our ticket -system on our website.
E-Mail: service@joy-it.net Ticket-System: http://support.joy-it.net Telefon: +49 (0)2845 98469 66 (11- 18 oclock)
For more information, please visit our website:
www.joy-it.net
Loading...