Joy Cooper Interconnect Cam-Lok Standart Series Accessories Catalog
73
Cooper Interconnect 4758 Washington Street LaGrange, NC 28551 252-566-3014
Cam-Lok® Standard Series
VULCANIZING KIT FOR CABLE SIZES #84/0
COMES COMPLETE WITH MOLD
BUSHINGS AND CRIMPING NEST FOR ONE
CABLE SIZE
. ADDITIONAL CABLE SIZES
CAN BE ACCOMMODATED BY ORDERING
ADDITIONAL MOLD BUSHINGS
(SEE CHART).
NOTE: V
ULCANIZING EQUIPMENT FOR
CABLE SIZES
#8-4/0 IS NOT
INTERCHANGEABLE WITH EQUIPMENT FOR
CABLE SIZES
350-750MCM. OTHER
SIZES ARE AVAILABLE
.
VULCANIZING PRESS FOR CABLE SIZES
#8-750MCM COMES COMPLETE WITH
MOLD BUSHINGS FOR ONE CABLE SIZE
.
A
DDITIONAL CABLE SIZES CAN BE
ACCOMMODATED BY ORDERING
ADDITIONAL MOLD BUSHINGS TO MATCH
YOUR CABLE SIZE
(SEE CHART)
Portable Vulcanizing Kits and Presses
COMPLETE VULCANIZING KITS
CABLE SIZE CABLE O.D. E1015 SERIES E1016 SERIES
#8 .440 A300120-1 --
#6 .510 A300120-2 --
#4 .570 A300120-3 --
#2 .660 -- A300100-3
#1 .740 -- A300100-4
1/0 .770 -- A300100-5
2/0 .820 -- A300100-6
3/0 .870 -- A300100-7
4/0 .930 -- A300100-8
VULCANIZING PRESSES ONLY
CABLE SIZE CABLE O.D. E1015 SERIES E1016 SERIES E1017 SERIES
#8 .440 A300121-1 -- --
#6 .510 A300100-2 -- --
#4 .570 A300100-3 -- --
#2 .660 -- A300103-3 --
#1 .740 -- A300103-4 --
1/0 .770 -- A300103-5 --
2/0 .820 -- A300103-6 --
3/0 .870 -- A300103-7 --
4/0 .930 -- A300103-8 --
350MCM 1.150 -- -- A300106-1
500MCM 1.310 -- -- A300106-2
750MCM 1.580 -- -- A300106-3
PLUG MOLDING BUSHINGS
CABLE SIZE NOMINAL CABLE O.D. E1015 SERIES E1016 SERIES E1017 SERIES
#8 .440 201015-3 -- --
#6 .510 201015-15 -- --
#4 .570 201015-18 -- --
#2 .660 -- 200895-20 --
#1 .740 -- 200895-21 --
1/0 .770 -- 200895-22 --
2/0 .820 -- 200895-23 --
3/0 .870 -- 200895-24 --
4/0 .930 -- 200895-17 --
350MCM 1.150 -- -- 200006-3
500MCM 1.310 -- -- 200006-6
750MCM 1.580 -- -- 200006-8
Cam-Lok
®
4758 Washington Street LaGrange, NC 28551 252-566-3014 www.cooperinterconnect.com
74
MOLDING PRESS PARTS AND VULCANIZING ACCESSORIES
Part No.
Description Part No. Description
All Mold Kits and Presses 100827-3 *Mold Press Pilot Light - red, complete with
wired socket
A400001 Assembly Tool 200704-2 Cartridge Heater - 350-750 MCM Molds
319735-1 Neoprene Vulcanizing Tape, 3/4" x 30" roll 200704-3 Cartridge Heater - #2-4/0 Molds
100566-1 *Mold Press Thermostat A100072 Cable Cutter - #2-4/0 Cable
A100632 Tool for removing contacts from insulators A200020-3 COM-A-LONG for pulling male contact in
E1012, E1016, E1018 Series
100826-3 *Mold Press Power On-Off Switch A200020-4 COM-A-LONG for pulling female contact in
E1012, E1016, E1018 Series
A20020-1 COM-A-LONG for pulling male contact in
E10115 Series
A200020-5 COM-A-LONG for pulling female contact in
E1017 and E1019 Series
A200020-2 COM-A-LONG for pulling female contact in
E1015 Series
A200020-6 COM-A-LONG for pulling male contact in
E1017 and E1019 Series
*Mold Parts for all Mold Presses A101208 2 oz. tube silicon grease for lubricating
synthetic rubber insulators
OTHER ACCESSORIES
CONNECTOR SERIES NO. SET
SCREW
COPPER
SHIM
QUANTITY PRESSURE
PAD
RETAINING
WIRE
E1010 All 100012-25 A100400-1
25
N/A 100573-1
E1012-61 & 62 100012-7 A100400-3
20
100575 100573-1
E1012 Single Set-Screw 100012-18 A100400-3
20
N/A 100573-1
E1016 Single Set-Screw 100012-18 A100400-3
20
N/A 100573-1
E1017 Double Set-Screw 100012-5 A100400-9
10
N/A 100573-2
E1018 Single Set-Screw 100012-18 A100400-3
20
N/A 100573-1
E1012 Double Set-Screw 100012-18 A100400-4
20
101214 100573-1
E1016 Double Set-Screw 100012-18 A100400-4
20
101214 100573-1
Gage block for calibrating crimper: #100891
E1015 AND E1016 SERIES CRIMPING NEST AND PRESSES
CABLE SIZE CRIMPING NESTS PART NO. CRIMPING PRESSES
#8 100514-1 A200914-1
#4-6 100514-2 A200914-2
#1-2 100514-3 A200914-3
1/0-2/0 100514-4 A200914-4
4/0 100514-6 A200914-6
VULCANIZING PARTS AND ACCESSORIES
A200020-1
Loading...