IN-0778 [2013A]
Floor Scales J825P
OPERATOR’S MANUAL
13
The outside of standard products may be wiped down with a
clean cloth moistened with water containing a small amount of
washing up liquid or disinfectant
EMC compliance
The following warning may be applicable to your machine.
WARNING:This is a class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
T
T
kg/
kg/
2
Navigating the setup menu
1. Press and hold until display shows
(approximately three seconds).
2. Release , display shows
3. Press to move across to the option or value you
require.
4. Press to select an option and save.
To exit the setup menu and save your changes:
Press until you see End.
Press to save your changes and return to weighing
mode.
11
Units key Selects weighing units
Hold key Retains average weight display.
1.4 Error codes
Err Overload
ErrL Below zero
ErrE EEprom error
Low battery warning
1.5 Specification
Capacity/resolution 250kg x 0.1kg
550lb x 0.2lb
Display Height 25mm
7 segment LCD
Operating temperature 5º C to 35º C
Weight 22kg
Dimensions
Platform 900mm x 550mm x 50mm
Display head 270mm x 90mm x 45mm
Power supply 6 x 1.2V metal hydride
rechargeable batteries
Recharge adaptor 1 x 100V-240V AC/13V DC
kg/
4
9
2 Weighing
kg/
6
Weighing units
Press to toggle between kg, lb and oz.
7
2.1 Hold function
This function enables you to weigh oversized objects that may obscure the
display. The system calculates an average weight reading and displays this
weight value. This makes the hold function ideal for weighing animals that may
be moving around on the platform.
8
1.6 Power supply
The indicator head contains six metal hydride re-chargeable batteries. The
low battery indicator is displayed when the battery power is insufficient to
power the scale.
Recharging the batteries
Insert the AC re-charger adapter into the socket on the indicator head to
recharge the batteries.
Low
Recharging time is approximately 14 hours.
Fully charged batteries should give approximately eight hours
of continuous use.
CAUTION: Always connect the AC adaptor to the indicator
head before connecting to the mains power supply.
Disconnect from the mains power supply before disconnecting
the adaptor from the indicator head.
AC adaptor
The 100V/240V recharge adaptor supplied with the PS250 is
provided with four convertion connectors:
2 pin European
3 pin UK
2 pin USA
2 pin Australia
5
3 Setup mode
3.1 Function setup
kg/
250kg x0.1kg / 550lb x 0.2lb
Low
Net
t
%
k
PCS
lb-oz
g
J825P
0
T
10
About your machine
1.1 Description
The PS250 is a self contained portable platform scale with a remote display. The
platform is constructed of mild steel; it has four adjustable feet for levelling and a
non-slip mat for the platform. A bracket and fixings are supplied for desk or wall
mounting the indicator head. For best results, always install the platform on a
hard, flat, level surface.
A stainless steel platform version is available.
1.2 Display
1.3 Key functions
Zero/ON/OFF key. Switches the scale on or off.
Tare key. Applies a tare value
0
T
3
3.2 Calibration
1. In setup mode, select and then select whether you want to use 1/2, full or
1/4
load for calibration (see ’Calibration weights’on page 12). The example
shown in these instructions uses kg weight units and 1/
2
load. Save your
selection and then switch off the scale.
Display shows zero count value.
12
Safety
Warnings
Safe installation
Take care when lifting and transporting heavy objects.
Do not overload the machine. Take care not to exceed the
weighing capacity of the machine.
Pluggable equipment must be installed near an easily accessible socket
outlet. Permanently connected equipment must have a readily
accessible disconnect device incorporated in the fixed wiring.
For your protection all mains (110V or 230V) equipment used
out of doors or in wet or damp conditions should be supplied from a
correctly fused source and protected by an approved RCD to BS7071 or
BS7288 or BS4293.
The mains lead must be connected to a supply outlet with a protective
earth contact. The electrical supply at the socket outlet must provide
overcurrent protection of an appropriate rating.
IF IN DOUBT SEEK ADVICE FROM A QUALIFIED
ELECTRICIAN.
Safe use
To avoid the possibility of electric shock or damage to the machine,
always switch off the machine and isolate from the power supply before
carrying out any routine maintenance.
Cleaning the machine
CAUTION: Harsh abrasives, solvents, scouring cleaners and alkaline
cleaning solutions, such as washing soda, should not be used
especially on the display windows. Under no circumstances should you
attempt to wipe the inside of the machine.
1
Loading...