Joovy Zoom 360, Zoom 360 53x Instruction Manual

©joovy 2014 • Document Version 040314

Zoom 360

53X

Joovy • 2919 Canton Street • Dallas, TX 75226 • [phone] • Fax [phone] • Email: [e-mail] • Website: www.joovy.com

Zoom 360 Instruction Manual

Please read this instruction manual completely before using this stroller. Keep these instructions for future reference.

• Failure to follow these instructions could result in serious injury or death.

• Never leave child unattended.

• Avoid serious injury from falling or sliding out.

• Always use safety belts and ensure that your child is positioned according to these instructions.

• Keep all small parts out of the reach of children while assembling the stroller.

• Be certain that the stroller is fully opened, all of the locking devices are engaged, and the parking device is engaged before allowing children
near the stroller.

• The parking device should always be engaged during the loading and unloading of children.

• Avoid serious injury from the front wheel falling off. Ensure the wheel is properly installed and secure before any use of the stroller.

• The seat is not suitable for a child under 3 months.

• The seat is intended for a child up to a maximum weight of 75 lbs.

• Use of the stroller with a child weighing more than 75 lbs. will cause excessive wear and stress on the stroller and may cause a hazardous
unstable condition.

• Keepwheelsatarecommendedtirepressureof35psiorasspeciedonanyreplacementtire.

• Never allow a child to step on the footrest to get into or out of the stroller.

• Do not use the stroller on stairways or escalators.

• The included parent organizer is for use ONLY on the Joovy Zoom 360 stroller. DO NOT use it on other stroller models.

• Never carry hot beverages or open containers in the parent organizer. Maximum weight allowed is 5 lbs.

• DonotaddanyattachmentnotspecicallyrecommendedbyJoovy.

• Any load attached to handle affects the stability of the product. Hanging purses, shopping bags, parcels, diaper bags, changing bags or other
accessory items from the handle bars or any other parts of the stroller may change the balance of the stroller and cause a hazardous unstable
condition.

• The maximum weight that can be carried in the storage basket is 5 lbs. Excessive weight may result in a hazardous unstable condition.

• The total weight of contents in the seat back pocket should be less than 3 lbs.

• The total weight of contents in the in-seat pockets should be less than 2 lbs.

• Never allow your stroller to be used as a toy.

• Discard all packaging materials properly. Do not allow children to play with them.

• Check your stroller for loose rivets, snaps, worn parts, and torn material or stitching on a regular basis.

• Also check the front wheel attachment and the tether strap attachment regularly for proper function and security.

• Discontinue use of the stroller should it malfunction or become damaged.

• While unfolding the stroller, be careful to keep your ngers from being pinched by moving parts.

1 Unpacking the Product

• Remove everything from the box and identify the parts using Figure 1.1 (not to scale).

A: stroller, B: front wheel, C: 2 rear wheels, D: parent organizer, E: tire pump, and documents (not shown).

• Discard all packaging materials properly including plastic coverings.

• DO NOT allow children to play with any packaging materials.

!

WARNING

!

WARNING

Adult assembly is required for this product.

No Tools Required.

2 Unfolding the Stroller

• Keep children away from stroller while unfolding.

• Orient the stroller with the seat facing up and the handle bars closest to you.

• If necessary, release the locking latch located on the lower right side by lifting the latch off of the catch. See Figure 2.1.

• Pull up on the handlebar so that the stroller unfolds to its upright and locked position.

CAUTION: While unfolding the stroller, be careful to keep your ngers from being pinched by moving parts.

• Ensure that the stroller is completely opened and the latching mechanism is secured before ANY further assembly or use of the stroller.

Please do not return this product to the store

If you experience any difculty with the assembly or use of this product, or if you have a
question regarding these instructions, please contact our Customer Service Department

at [phone] between the hours of 8:30 am and 5:00 pm Central Time.

!

WARNING

ALWAYS keep children away from the stroller when unfolding.

Possible pinching hazard - Be careful when unfolding the stroller.

5 Front Wheel Swivel Locks

The stroller can be operated with the front wheel in either swivel mode or locked mode.

• To put the front wheel into locked mode, locate the plastic locking lever just above the front wheel.

• Push this lever to the right (clockwise) and rotate the wheel until it locks automatically in the straight position and an audible click is heard.

See Figure 5.1.

• To unlock the front wheel and use it in swivel mode, push the lever to the left (counter clockwise) until an audible click is heard.

7 Operating the Canopy

• To open the canopy, pull forward on the front edge of the canopy until it is fully extended.

• The canopy and visor can be adjusted into several positions ranging from fully closed to full extended, or any position in between.
See Figure 7.1.
NOTE: The top rear portion of the canopy has a roll back window. To open, pull the rear edge up, roll the ap forward and secure using the

T and elastic attachment.

• To close the canopy, push the front edge of the canopy toward the rear of the stroller.

• Engage the two sets of snaps on the underside of the canopy above the seat to allow maximum head room. See Figure 7.2.
NOTE: When you open the canopy with the snaps engaged, these snaps will automatically unsnap.

6 Rear Wheel Brakes

This stroller is equipped with a linked parking brake for the rear wheels.

• Before placing your child into the stroller or removing them from the stroller, be certain that the rear parking brake is engaged.

• To engage the rear parking brake, push down on the brake lever on the right rear wheel hub of the stroller until you hear an audible click.

See Figure 6.1.

• Check that the brake is properly applied by attempting to push the stroller backwards and forwards.

• To release the brake, lift up on the brake lever until it locks into the UP position and you hear an audible click. See Figure 6.2.

!

WARNING

Always engage the parking brake when the stroller is not being pushed so that it will not roll away. Never leave stroller unattended, especially

on a hill or incline, as the stroller may tip over or slide.

3 Installing/Removing Rear Wheels

• Take one rear wheel and insert it into one of the rear wheel hubs until an audible click is heard.
NOTE: You may need to push the wheel with some force to get it past the locking mechanism. See Figure 3.1.

• Pull outward on the wheel to ensure the wheel is installed properly.

• To remove a wheel, push down on the metal tab on the rear wheel hub and then pull outward on the wheel. See Figure 3.2.

4 Installing the Front Wheel

• With the stroller still tilted backwards on the handle bar, remove the plastic protector from the front forks and discard properly.
NOTE: rst need to lock the forks into place. See section on “Front Wheel Lock” for this procedure.

• Loosen the round nut on one end of the front wheel axle just enough so that the wheel will slide onto the frame forks. BE CAREFUL that you

do not take this nut off completely. If this occurs, be sure to reassemble the metal washer and spring onto the axle before reassembling the
nut onto the axle.

NOTE: The metal washer must be assembled to the axle with the small metal tab facing IN toward the wheel and the SMALL end of the

spring also facing IN toward the wheel.

• Make sure the safety lock on the opposite end of the axle is in the UNLOCKED (straight out) position.

NOTE: You can assemble the front wheel with the safety lock on either side of the stroller.

• Slide the wheel onto the frame forks being sure that the metal washer is on the OUTSIDE of each fork. See Figure 4.1.

• Make sure the small metal tab on the washers on BOTH sides of the wheel are placed into the small hole in the fork. This is a secondary
retaining method to help prevent the wheel from sliding off the forks in case the safety lock accidentally opens.

• While holding the safety lock in the open position, tighten the round nut BY HAND in a clockwise direction until it is as tight as you can get it.

• Push the safety lock DOWN to the closed position and ensure it is tight. See Figure 4.2. You may need to loosen the round nut slightly to
fully close the safety lock.

• Pull outward on the wheel to ensure the wheel is installed properly.

• If the wheel is loose or able to be pulled off the forks, loosen the safety lock to the unlocked position and tighten the round nut further.
Repeat until the wheel is secure.

• To remove the wheel, rotate the safety lock to the unlocked position and loosen the round nut counter clockwise until loose enough to slide
the wheel off of the frame forks.