Jonti-Craft 1382JC User Manual

Jonti-Craft, Inc.

171 Hwy 68
P.O. Box 30
Wabasso, MN 56293

WARNING— CHOKING HAZARD/SHARP POINTS:

Assembly hardware contains small parts and components with sharp points. Adult assembly required.

Tools Required:

-Medium Phillips Screwdriver

CAUTION— ELECTRICALLY OPERATED PRODUCT:

 For indoor use only on a dry, level surface. If spills occur, wipe up all spilled water from floor

and on product promptly.

 Adult supervision is required at all times during the use of this product.
 Do not allow children to plug in or unplug power cord from wall outlet, access any of the

components inside of the cabinet, and/or fill or empty the water tanks.

 Inspect power cord and other components for damage before every use. Do not attempt to

modify or repair damaged cords or other components. Repairs should only be made by a
qualified electrician or plumber.

 Locate product in such a way that the power cord can be routed to prevent it from being tripped

over, crushed, cut, or damaged in any other way.

 Do not use an extension cord with this product. Plug item directly into a wall outlet.
 This product has a 3-prong (grounded) plug on the power cord as a feature to reduce the risk of

electric shock and should be plugged into a properly grounded 3-prong wall outlet. Do not
attempt to alter the plug or use 2-prong adapters.

 Product must be plugged into a grounded 120V 60Hz outlet.
 Turn off and unplug product from wall outlet when filling/emptying tanks or performing

maintenance.

 Casters must be in the locked position when the product is in use.

Electrical Input: 120V AC, 60 Hz, 0.35A

Please refer to label on bottom of product

for manufacturing date information.

Instructions for: 1380JC Series Portable Sinks

(without water heater)

Hardware Package HCII
Qty Description
(2) XALW Black Handle
(4) XAUN #6 x 1-1/4" Trusshead Screw
(1) XCJO Rubber Drain Plug
(1) XCCV Flat Washer, 1-1/2" O.D.

Also included with the product:
(1) Faucet Spout
(2) Faucet Handles
(2) Faucet Handle Screws
(1) “H” Faucet Cover
(1) “C” Faucet Cover

Read all instructions before using unit. Failure to follow all instructions below may result in electric shock,
fire, and/or damage to the unit.

DHCII – Rev. B – 22 October 2019
800-543-4149
507-342-5169 Page 1 of 5

www.jonti-craft.com

Jonti-Craft, Inc.

171 Hwy 68
P.O. Box 30
Wabasso, MN 56293

1) Begin by removing and

discarding the plastic cap in
the center of the faucet
base.

2) Place the end of the spout

with rubber O-rings into the
center hole of faucet.
Carefully push the spout into
the faucet until nylon ring is
seated on faucet, making
sure the rubber O-rings stay
in the grooves on the spout.
Slide threaded sleeve down
and finger tighten to secure
spout to faucet.

3) Align hole in handles with

stems of the faucet base.
The stem of the faucet and
the hole in the handle have
flat spots which need to line
up with each other. Make
sure handles seat completely
then install one screw to
secure each handle. Tighten
using a medium Phillips
screwdriver. Repeat for other
handle.

4) Install the faucet covers by

pressing them into place on
the faucet handles.

NOTE: Because this item
does not include a water
heater, water that comes
out of the spout from
either side of the faucet
will be the same
temperature as the water
in the clean water tank.

5) Attach the black handles to

the doors using the #6 x 1­1/4" trusshead screws
provided and a medium
Phillips screwdriver.

6) Insert power cord through

the hole in the bottom near
the back of the unit. Pull the
cord to the outside of the
unit.

Assembly Instructions:

(Pictures may vary slightly from actual unit.)

DHCII – Rev. B – 22 October 2019
800-543-4149
507-342-5169 Page 2 of 5

www.jonti-craft.com