Jolly Mec BP07 Installation And Use Card

Air
controller

INSTALLATION AND USE CARD

To be carefully kept by the purchaser

CONTENTS

ASSEMBLY INSTRUCTIONS FOR THE INSTALLER

1.1 Recommended assembly diagrams ..................................................................................................................................................................................................................................................................3

1.1.1 SOLUTION 1: for new fireplaces or inserts

......................................................................................................................................................................................................................3

1.1.2 SOLUTION 2: for new fireplaces or inserts

......................................................................................................................................................................................................................4

1.1.3 SOLUTION 3: for inserts

..........................................................................................................................................................................................................................................................................4

1.1.4 SOLUTION 4: for new fireplaces or inserts

......................................................................................................................................................................................................................5

1.1.5 SOLUTION 5: for new fireplaces or inserts

......................................................................................................................................................................................................................5

1.1.6 SOLUTION 6: for new fireplaces or inserts with remote control

..............................................................................................................................................................6

1.2 Controller BP07 wiring diagram

..............................................................................................................................................................................................................................................................................7

1.3 Technical characteristics

..................................................................................................................................................................................................................................................................................................8

USE AND MAINTENANCE INSTRUCTIONS FOR THE USER

1.4 Use of controller BP07 ......................................................................................................................................................................................................................................................................................................9

Read this card carefully and follow the instructions for quick
installation and correct use of the fireplace.

Before starting installation, read the card carefully and follow
the instructions; failure to do so could invalidate the warranty
and compromise fireplace performance and safety.

This installation card is an integral and essential part of the
product and must be given to the user.

It must kept in safe place and carefully consulted, as it provides
important information on safety during the installation, use and
maintenance stages.

Incorrect installation can cause damage and injury, for which
the manufacturer cannot not be held liable.

The unit must only be used for its intended purpose. Any other
use is deemed improper and therefore dangerous.

The manufacturer declines any contractual or non-contractual
liability for damage caused by errors in installation or use,
failure to follow the instructions contained in this card, or
installation in places or rooms unsuitable for the
characteristics of the product.

All rights to reproduction of this card belong to JOLLY-MEC
CAMINETTI S.p.A.

The descriptions and illustrations provided in the following
publication are not binding.

JOLLY-MEC CAMINETTI S.p.A. reserves the right to make any
changes it deems necessary at any time.

This card cannot be given to third parties to read without the
written permission of JOLLY-MEC CAMINETTI S.p.A.

The technical instructions for assembly contained in this
handbook are considered basic requirements. The regulations
in some countries may be more restrictive; in this case carefully
comply with the regulations in the country of installation.

A

C

B D E

F

Before fitting the exchanger or positioning the fireplace, choose
the required electrical assembly diagram from among those
given, then prepare the necessary paths for the connection
cables, obtained from passages in tubes with sheathing for
electrical cables of approved types.

The fan and 230V line cables must not be inserted in the same
sheathing used for the probe (or thermostat) and display cables.

1.1.1 SOLUTION 1: for new fireplaces or inserts

Components

Controller positioned under the fireplace, inside the cladding, or
in the compartment obtained for the fan in already existing
cladding for Universaljolly (see fireplace instructions). Display
positioned at side on cladding hood.

For this important requirement, the following diagrams use the

colour RED

- - - - - -

for 230V cables and BLUE

- - - - - -

for very

low voltage cables.

In the following examples

the

RADIO FREQUENCY remote control

(an OPTIONAL accessory) is represented with n. F.

A

B

C

D

E

F

Main switch

Controller

Command and control
display

Fan

Probe or thermostat

Optional remote control

IMPORTANT!

Always make sure the temperature where the controller and display are placed does not exceed 60°C.

1.1 Recommended assembly diagrams

A

C

B D E

F

A

B

D E

C

F

1.1 Recommended assembly diagrams

4

1.1.2 SOLUTION 2: for new fireplaces or inserts

Components

A

B

C

D

E

F

Main switch

Controller BP07

Command and control
display

Fan

Probe or thermostat

Optional remote control

Controller positioned under the fireplace, inside or outside the
cladding, or in the compartment obtained for the fan in already
existing cladding for Universaljolly. Display positioned at side on
the cladding plinth.

1.1.3 SOLUTION 3: for inserts

Components

A

B

C

D

E

F

Main switch

Controller BP07

Command and control
display

Fan

Probe or thermostat

Optional remote control

Controller and display positioned at side on the cladding plinth.
Display attached to the controller box cover with velcro (supplied);
or with self-tapping screws (3.5x9.5), making sure to leave at
least 5mm between the screw and the electronic board in the box.

1.1 Recommended assembly diagrams

5

A

B

C

D E

F

1.1.4 SOLUTION 4: for new fireplaces or inserts

Components

A

B

C

D

E

F

Main switch

Controller BP07

Command and control
display

Fan

Probe or thermostat

Optional remote control

1.1.5 SOLUTION 5: for new fireplaces or inserts

Components

A

B

C

D

E

F

G

Main switch

Controller BP07

Command and control
display

Fan

Probe or thermostat

Optional remote control

Humidifier access recess

A

D E

F

C

B

G

Controller and display away from fireplace, maintaining the
maximum distances recommended in the wiring instructions.

Controller positioned in the fireplace hood, with the display
positioned above it, or elsewhere. N.B.The temperatures where the
controller is placed must be below 60°C.

A

DBCE

F

1.1 Recommended assembly diagrams

6

1.1.6 SOLUTION 6: for new fireplaces or inserts with remote control

Components

A

B

C

D

E

F

Main switch

Controller BP07

Command and control
display

Fan

Probe or thermostat

Remote control

Controller and display both positioned under the fireplace inside
the cladding; or in the fan compartment (see fireplace
instructions) for Universaljolly units. Display attached to the
controller box cover with velcro (supplied); or with self-tapping
screws (3.5x9.5), making sure to leave at least 5mm between
the screw and the electronic board in the box.

1.2 Controller BP07 wiring diagram

7

Manual

version

Automatic

version

Thermostat

Probe PT100

Fan

Control display

Earth

Connect to the earth

of the metal box

230V line

1.3 Technical characteristics

Technical characteristics

- Connection to radiofrequency RFRC (868MHz, modulation FSK).

- Connection to boiler by means of non-polarised pair 2x0.75mm, max. length 30m.

- No type of auxiliary power supply or batteries are necessary.

- Operating temperature range 0÷65°C.

- Reserve charge time in absence of connection/power of at least 8 hours.

- Permanent storage of user programmes and settings.

- The display is connected to the board by means of two non-polarised wires, through which it is fed and communicates with the board.

- The characteristics of the connection line are as follows:
Number of wires: 2x0.75mm
Type of cable: twin wire*

- Max. cable resistance: 2

- Polarity : polarity free

* In case of places with high electrical noise, a screened or twisted cable must be used.

Luminous signals

The board has 3 LED’s for showing operation status and any faults.

2

,5Ω

LED COLOUR OFF ON FLASHING

DL1 yellow communication not active communication active not provided for

DL2 red no fault probe fault not provided for

DL3 green no power power on not provided for

Jumper check only for service technicians

Retrofit controllers QUA/ELET AND QUA/UNIV Retrofit controllers QUA/ARIA1-2

NO jumperEOperation with PROBE Automatic Version YES jumperEOperation with THERMOSTAT Manual Version

8

1.4 Controller BP07 use

9

DAY SET

ON

Main features

The controller is arranged for control of the room air fan, for setting
the optimum air delivery level. The ventilation level can be manually
set by the user or in automatic mode.
In automatic setting (possible in the version with temperature probe),
the ventilation level is set according to the fireplace temperature.
A fan operation mode is provided for also with the fireplace off, for
room ventilation.

The user interface is in wired version, already arranged for the
radiofrequency version.
Through the user interface it is possible to set the various operation
modes and identify any faults.
Display of room temperature (with remote control only).

DISPLAY

- Change operation status
Summer/Winter

- Display fan speed in automatic

Increase selected value

in manual programme

Decrease selected value

in manual programme

No communication with fireplace

(with remote control only)

The controller is arranged for
association with the remote control.

norF

Operation programme

AU = Automatic
LX = manual with ventilation

level X (1-9)

OF = Off

RF reception in progress Winter Mode (if not present the

controller is set to Summer mode)

Change operation
programme Off/Manual/Automatic

1.4 Controller BP07 use

10

Operation status

Press the button to go from Summer status to Winter and vice versa:

Summer 왘 Winter 왘 Summer

Operation programme

—- —- —- —- —- SUMMER —- —- —- —- —-

OF LX (1-9) OF

OFF 왘 Manual 왘 OFF

—- —- —- —- —- WINTER —- —- —- —- —-

OF LX(1-9) AU OF

OFF 왘 Manual 왘 Automatic 왘 OFF

Press the button to go from one operation programme to another :

Setting the required ventilation level

In Manual the set ventilation level LX will appear on the right on the display, where X can assume values of 1 to 9.

Use the buttons .to modify the set value X.

Display of ventilation level in automatic (with remote control only)

Press the button for 3 seconds to display the current ventilation level (which can momentarily differ from that set, for example in
automatic). The ventilation level LX will appear in the middle of the display, where X can assume values of 1 to 9.

To return to normal operation just press the button again or wait 60 seconds without pressing other buttons.

Dissipation programme

If the fireplace reaches excessive temperatures a programme called Dissipation will be automatically activated (with probe only) and
signalled with the message Ht (High Temperature). This programme has priority over all the other settings, which will possibly be ignored.

NOTE!

When the contact thermostat is present on the fireplace, the fan speed “Automatic” function is not present.

1.4 Controller BP07 use

11

Associating an RFRC02 with base RFIU02 (RF installation)

To associate the display-remote control pair, proceed as described below. Note: To create the association it is necessary to operate on the
display and the remote control, therefore it is advisable to keep them within reach.

1. On REMOTE CONTROL:

- Press the button for 5 seconds to access the Programming mode (indicated by the message LO).

- Press the button once and the icons and the message n Zn (No Zone) appear, with n flashing to indicate no association.

Press the button for 5 seconds until the message Ln (Link) appears.

2. On DISPLAY:

Now put the display on standby for association request, from normal operation by pressing the button once the message Inst (Install)
will appear flashing.

3. On REMOTE CONTROL:

- Press the button and wait a few seconds. If the operation was successful the message LO (Link OK) appears, otherwise LE
(Link Error) appears.

- In both cases it is possible to return to the initial window by pressing the button (or to exit programming completely).

In case of positive result the display automatically returns to normal operation (otherwise press or wait 60 seconds) and the new
message on the remote control will be 1 Zn in place of n Zn.

Status+Operation programme Summer+OFF

Ventilation level in manual L = 5

Function Factory setting

Summary of displays and Factory settings

Quality of the RF signal and notes on position of the device (with remote control)

The quality of RF communications can be displayed at any time, in order to select the correct place of installation and guarantee correct
operation of the system. In fact, the communications in RF systems can deteriorate as a result of an incorrect position inside the house. To
check the quality, proceed as follows.

- Press the button for at least 3 seconds to access the Programming mode (indicated by the message LO).

- Press the button until the message X rF appears, with X flashing to indicate the communication quality level (from 0 to 4):

0 = No communication (no association/signal or positioning unsuitable)
1 = Signal present but weak (positioning not very suitable in presence of interference)
2 = Signal sufficient to guarantee correct operation
3 = Good signal
4 = Optimum signal

To return to normal operation, press the button or wait 60 seconds.

Fault signalling

In case a boiler anomaly, the message Er:XX will appear on the display in normal operation, where XX indicates the type of fault.

SM/032-GB rev. 1 01/2008

Via Fontana, 2 - 24060 Telgate - BG - ITALIA
Tel. [phone] - Fax [phone]

www.jolly-mec.it - [e-mail]