Jolimark BP-1000K (Model B) User Manual

User's Manual

BP-1000K (Model B)

BP-1000K User’s Manual

- i -

Declare

About Trademark

Corporation names and product names are the registered trademarks or commodity names of the corporation.

＊ EPSON is a registered trademark of Seiko Epson Corporation.

＊ ESC/PK2 is a registered trademark of Seiko Epson Corporation.

＊ OKI is a registered trademark of Oki Data Corporation.

＊ OKI 5530SC is a registered trademark of Oki Data Corporation.

＊ IBM is a registered trademark of International Business Machines Corporation.

＊ IBM 2391 is a registered trademark of International Business Machines Corporation.

＊ Windows is a registered trademark of Microsoft Corporation.

＊ OLIVETTI is a registered trademark of Olivetti Corporation.

＊ OLIVETTI PR2 is a registered trademark of Olivetti Corporation.

BP-1000K User’s Manual

- ii -

Important Safety Instructions

Read all of these instructions carefully and thoroughly and save them for later reference. The unauthorized operation would lead to malfunction or accident. Manufacturers have no responsibilities for the problems which are led by misoperations.

1. Follow all warnings and instructions in the manual as well as marked on the product.

2. Do not touch the print head if the printer has just been recently used as the print head may be hot.

3. Do not put your fingers under the left and right tractor sprocket covers of the tractor (optional) when installing the tractor paper.

4. Unplug this product from the power outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

5. Do not use this product near water.

6. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to you or the product.

7. Slots and openings on the cabinet and the back or bottom are provided for air ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heater. This product should not be placed in a built-in installation or kiosk stand unless proper ventilation is provided.

8. This product should never be placed near or over a radiator or heat origin, and should avoid of direct sunshine.

9. Do not locate this product where the cord would be walked on. When the cord or the plug is mangled, please stop using and get a new one replaced. Make sure the old one is far away from the printer, so it can avoid someone who does not know the inside story getting damage.

10. Do not use in locations subject to high humidity or dust levels. Excessive humidity and dust may cause equipment damage or fire.

11. Never push objects of any kind into this product though cabinet slots as they may touch dangerous voltage dots or short out parts.

12. Don’t remove the printer’s out-cover and repair the printer. When needed, call or take it to the professional.

13. To ensure safety, please unplug this product prior to leaving it unused for an extended period. The wall outlet you plan to connect to should be nearby and unobstructed.

14. Unplug this product from the power outlet and leave servicing to qualified service personnel under the following conditions:

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally when the operating instructions are followed.

E. If the product has been dropped or the cabinet has been damaged.

F. If the product exhibits a distinct change in performance, it indicates a need for service.

Note: The contents of this manual are subject to change without notice.

* All parts of the printer can be recycled. When it is abandoned, we can call it back freely. Please

BP-1000K User’s Manual

- iii -

Table of Contents

Declare..........................................................................................................................................................i

Important Safety Instructions

....................................................................................................................ii

Chapter 1 Product Features

.......................................................................................................................1

Chapter 2 Checking and Inst

alling ............................................................................................................3

2.1 Unpacking and Checking ....................................................................................................................3

2.2 Unpacking the Protect

ive Materials.....................................................................................................3

2.3 Main Parts of the

Printer......................................................................................................................4

2.4 Installing the Printer

............................................................................................................................4

2.4.1 Choose Proper Inst

alling Place ....................................................................................................4

2.4.2 Installing the Paper Feed Knob

....................................................................................................4

2.4.3 Installing the Ribbon Cartridge

.....................................................................................................5

2.5 Connecting to Y

our Computer .............................................................................................................7

2.5.1 Connecting the Par

allel Interface..................................................................................................7

2.5.2 Connecting the USB Interface

......................................................................................................8

2.5.3 Connecting the Serial Interface Cable

..........................................................................................8

2.5.4 Connecting the Ethernet Interface Cable

......................................................................................9

2.6 Connect the Power Core

.....................................................................................................................9

2.7 Installing the Driv

er .............................................................................................................................9

2.8 Network Settings

...............................................................................................................................12

2.8.1 Connecting Printer

......................................................................................................................12

2.8.2 Setting IP Address

......................................................................................................................12

2.8.3 Installing Printer Network Driver

.................................................................................................14

Chapter 3 Paper Process

.........................................................................................................................22

3.1 Paper Switch.....................................................................................................................................22

3.2 Loading the Cut Sheet ......................................................................................................................22

3.3 Loading the Passbook.......................................................................................................................23

3.4 Loading the Vertical Certificate..........................................................................................................23

3.5 Loading the Thick Pap

er ...................................................................................................................24

3.6 Installing Tractor Pap

er .....................................................................................................................24

3.7 Tearing the T

ractor Paper..................................................................................................................25

Chapter 4 Control Panel

...........................................................................................................................27

4.1 Key, Indicator Light and LCD Display on Control Panel ....................................................................27

4.2 Basic Operation of Control Panel

......................................................................................................27

4.3 The information on the LCD Displ

ay When at Stand by State ........................................................... 28

4.4 Use of the Menu Setup System

.........................................................................................................29

4.4.1 Change the Current Setting of

the Printer...................................................................................29

4.4.2 Printing the Current Setting Report

.............................................................................................30

4.4.3 Menu Item Description

................................................................................................................32

4.4.4 Online Aptitude Parameter Setti

ng .............................................................................................33

4.4.5 Restoring Factory P

rinter Settings..............................................................................................34

4.4.6 Head P

in Test.............................................................................................................................34

4.5 TOF Adj

ustment ................................................................................................................................35

4.6 Tear Off Position Adj

ustment .............................................................................................................35

BP-1000K User’s Manual

- iv -

4.7 The Self Test Functions..................................................................................................................... 35

4.7.1 ASCII Self-Test

...........................................................................................................................35

4.7.2 Chinese Self T

est Mode..............................................................................................................35

4.7.3 H Pattern T

est.............................................................................................................................36

4.7.4 Hex M

ode...................................................................................................................................36

4.7.5 Dot Alignment Mode

...................................................................................................................36

Chapter 5 Maintenance and

Troubleshooting........................................................................................38

5.1 Cleaning the Printer ..........................................................................................................................38

5.2 Problems and Solutions

....................................................................................................................38

5.3 Error Indication on the Display of Control Panel

................................................................................40

Chapter 6 Paper S

pecification ................................................................................................................. 42

6.1 Cut Sheet Printable Area................................................................................................................... 42

6.2 Tractor Paper Print

able Area ............................................................................................................. 43

6.3 Passbook Prin

table Area................................................................................................................... 44

6.3.1 Size Specifications of

Horizontal Passbook................................................................................44

6.3.2 Size Specifications of V

ertical Certificate....................................................................................45

Appendix A Technical S

pecification........................................................................................................46

A.1 Technical Specification......................................................................................................................46

A.2 Parallel I

nterface...............................................................................................................................48

A.3 USB Interface

...................................................................................................................................49

A.4 Serial Int

erface..................................................................................................................................49

A.5 Ethernet Interface

.............................................................................................................................51

A.6 Cautions of Printing

..........................................................................................................................51

BP-1000K User’s Manual

- 1 -

Chapter 1 Product Features

Thank you for choosing Jolimark passbook printer. The printer is a product of 24 pin high quality 110 column multifunction passbook/certificate/report printer, it can fulfill your printing requirement.

The printer has the specialties as follows:

z Auto fit paper thickness function

Use floating flat platen, have the function of Auto fit paper thickness which makes the printing quality better. Its maximum thickness can reach 3mm.

z Have the function of auto Load/Eject and auto skew adjustment

Cut sheet can feeding the paper in the front of the printer and auto load to the printing position. Also it has the function of Auto Skew Adjustment. If the paper is in less than 30 ° skews, it will auto adjust. The tractor paper is installed on the tractor (optional). You can control it by pressing button Load/Eject or LF/FF, so that the paper can auto feeding to the printing position. After printing, the paper would eject from the front of printer which make it easy to tear.

z Auto detecting paper margin function

It can base on the position of the paper to adjust the printing position, which avoids it printing out of the paper.

z Any position to feed paper and printing function

Adopt professional design of auto fit paper insert. The printer can fulfill any position to feed paper and printing function in the printable area.

z One button to control the switch in paper modes

You only need to press"the paper switchover" button which make it switch in 4 paper modes. It is more intelligence, convenience and simple.

z Paper tear function

This function can make the tractor paper auto feed to the paper tear position, so that it can tear paper accurately after printing.

z Function of paper eject

With this function the user can easy operate it by the control panel to eject the cut sheet and tractor paper from the printer.

z Flat push paper feed mechanism which solve the problem of paper jam

Innovative flat push paper feed mechanism which can make paper not skew and deforming, so that when it printing some special files (such as passbook, certificate, 1+n invoice, envelope, post card and labels) will not jam paper.

z Control panel with high definition LCD display

You can know the current printing state of the printer through the LCD display, and you can also finish all the function setting through the LCD display.

z Holistic engineering design by the printer combine the user

With the design of making the power switch, the operation button and the LCD display in the front of the printer. The knob is designed to at the right side of the printer, which make sure the user feel much comfortable and convenience.

BP-1000K User’s Manual

- 2 -

z Safety design of humanization

The printer installing a sensor of cover open which make the printer stop printing whenever the upper cover does not be covered and make the print head move to the middle position. If you close the cover it will continue printing again.

z Function of auto select the data transmission interface

The printer fittings the parallel interface, USB interface, serial interface and Ethernet interface. (According to specific interface standard) So it can receive the date of parallel interface (Centronics) and USB interface. Once the computer send out the date, the printer can detecting the type of the data and auto switch to the right interface to receive it.

z High speed and super high speed printing with high quality

The printer can be print the high quality by 10 CPI at normal mode with the speed of 100CPS. At high speed mode, the printer can be printing with the gap of 10 CPI at the speed of 300CPS. At super high speed mode, the printer can be printing with the gap of 10CPI at the speed of 360CPS.

z High resolution of image printing

Max resolution of 360DPI (horizon) × 360DPI (perpendicularity) and the image is most definitely.

z Compatibility

The command compatible the OKI 5530SC, Epson ESC/PK2, Olivetti PR2 and IBM which are popular control command in the printer market.

z Letter quality font

There are Roman, Sans Serif, Courier, Prestige, Script, OCR-A&B etc. characters which can compare with other band of printer.

z Bar code memorizer

There are standard bar code types show as follow: EAN-13, EAN-8, Interleaved 2 of 5, Matrix 2 of 5, Industrial 2 of 5, Code 39, Code 128 B, Code 128 C, NW-7.

z Electronic menu

The printer can setting the parameter by itself and saving into the memorizer of the printer.

z Enhance Chinese character set

This printer contains GB18030 Chinese character set and also supports 4 bytes Chinese printing.

z Contain Bank system used character set

It supports bank system used character set print out.

z Contain any position paper feed function

It supports to feed paper in any position on the paper path.

z Contain break pin compensation function

User can set the printer to print using the pin which is in good condition to compensate the break pin.

z Pin switch printing mode

User can set pins to switch while printing form transverse line in order to improve print head life.

BP-1000K User’s Manual

- 3 -

Chapter 2 Checking and Installing

2.1 Unpacking and Checking

Check the following items in the package, if any of these items is missing, please contact your dealer. (1) Printer; (2) Ribbon cartridge (JMR115); (3) Paper feed knob; (4) Driver CD; (5) Power cord; (6) Facility user's guide (as Figure 2-1 show).

2.2 Unpacking the Protective Materials

1. Open the packing box, lift up the printer, open the upper cover of the printer, remove the protective materials of the upper printer frame.

2. Save all the original packing materials, so that it can use when transporting the printer (show as figure 2-2).

Figure 2-2 Unpacking protective materials

Figure 2-1 Items in the packing list

Printer Ribbon cartridge (JMR115)

Driver CD

(Including User’s Manual and Driver)

Power cord

Paper feed knob

Facility user's guide

Protective materials

BP-1000K User’s Manual

- 4 -

2.3 Main Parts of the Printer

Figure 2-3and Figure 2-4 mark the names of main parts.

Note: According to specific interface standards

2.4 Installing the Printer

2.4.1 Choose Proper Installing Place

When choosing the installing place please consider following problems:

1. The laying place must be plane and fixing.

2. When printing tractor papers, the paper must be fed through the rear of the printer. So you should leave enough space for safety printing. If you put the tractor paper on the floor, the horizon minimum range between the printer and the paper should over 30mm. The printer should be place where backside of the printer is away the wall over 60cm, which avoid the paper break off from the tractor (optional).

3. Easy for operation, the table board should not be too high, it can be suitable about 60cm.

2.4.2 Installing the Paper Feed Knob

1. Insert the paper feed knob into the fixing hold on the right on the printer (Show as figure 2-5).

Figure 2-3 Main parts of the printer (Front view)

Figure 2-4 Main parts of the printer (back view)

Upper cover

Upper frame lever

Print head

LCD display

Paper feed knob

Control panel

Ribbon cartridge

Carriage shaft

Power switch

Ribbon guide board

Printer rear cover

Tractor (Optional)

Parallel interface

USB interface

Power supply inlet

Serial interface or Ethernet interface

BP-1000K User’s Manual

- 5 -

Note：The D shape placket of the knob should match the D shape shaft inside the printer cover.

2. Press the paper feed knob till it very close up the cover of the printer.

2.4.3 Installing the Ribbon Cartridge

1. Switch on the Power and open the upper cover of the printer. The print head will move to the middle position automatically.

2. Untie the upper frame lever of both sides, pull the upper frame up, and switch off the power.

3. Hold the edge of the paper guide slice of both sides, and turn over it downwards.

Figure 2-6 Move the print head to the middle position

Figure 2-7 Pull up the upper frame

Paper feed knob

Figure 2-5 Installing the Paper feed knob

Print head

BP-1000K User’s Manual

- 6 -

4. Buckle the bottom and upper button of the ribbon frame in turn into the slot of the printer frame.

5. Fix the ribbon core into the ribbon path.

6. Turn the ribbon knob in the direction of the arrow to remove any slack from the ribbon. Then close the ribbon guide board.

ure 2-10 Installing the ribbon core

Figure 2-9 Installing the ribbon cartridge

Figure 2-8 Turn over the guide of the carriage

BP-1000K User’s Manual

- 7 -

7. Press down the upper frame and pull the upper frame lever to the front, lock the upper frame lever by pulling it backwards after the upper frame is in correct position. At last, close the upper cover.

Note: 1. When you remove the ribbon cartridge, please refer to the description on the right and

follow the steps.

2. When the print out becomes faint, you need to replace the ribbon cartridge. Use of worn out ribbon will damage the print head.

3. Never move the print head when the printer is ON condition or else the printer may be damaged. Don’t touch the print head as it will be hot during printing.

4. Use genuine Jolimark JMR115 consumables or else warranty will be void.

2.5 Connecting to Your Computer

The printer can configured with a parallel interface, USB interface, serial interface and Ethernet interface. (According to specific interface standards) Connect your computer to the desired interface as your requirement. (Show as picture 2-13, 2-13, 2-14 and 2-15)

Note: Before connecting the parallel interface, please make sure the power of the printer is shut

down. Must after tighten the cable you may turn on the power, or it will damage the printer.

2.5.1 Connecting the Parallel Interface

1. Turn off both the computer and the printer. Plug the parallel cable connector securely into the printer’s parallel interface. Squeeze the wire clips together until they lock in place on either side of the connector.

2. Plug the other end of the cable into the computer’s parallel interface; then tighten the screws on either side of the connector.

Figure 2-11 Tighten up the ribbon core

Figure 2-12 Lock the upper frame

BP-1000K User’s Manual

- 8 -

2.5.2 Connecting the USB Interface

1. Plug the USB cable A end (flat shape) into the computer's USB interface.

2. Plug the USB cable B end (square shape) into the printer's USB interface.

Caution: Don’t impact the plug after connecting to the USB interface.

2.5.3 Connecting the Serial Interface Cable

1. Turn off both the computer and the printer. Plug the serial interface cable connector securely into the printer’s serial interface. Then tighten the screws on either side of the connector.

2. Plug the other end of the cable into the computer’s serial interface; then tighten the screws on either side of the connector.

Figure 2-13 Connecting the parallel interface

Figure 2-14 Connecting the USB interface

Parallel interface

Parallel cable

Wire clips

USB Interface

USB cable

Serial interface

Serial cable

Screw

Figure 2-15 Connecting the serial interface cable

BP-1000K User’s Manual

- 9 -

2.5.4 Connecting the Ethernet Interface Cable

Plug the crystal end of the Ethernet interface cable (RJ-45) into the printer's Ethernet interface, and then plug the other end into the LAN’s entrance as shown in Figure 2-16.

Note: Please refer to the user’s manual for the detailed instructions of internet settings.

2.6 Connect the Power Core

1. Make sure the power switch on the printer is turned off.

2. Make sure the voltage required by the printer matches that of your electrical outlet.

3. If the power cord is not attached to the printer, connect it to the power supply inlet on the printer.

4. Plug the power cord into a properly grounded electrical outlet. (show as figure 2-17)

Note：1. If the rated voltage and your outlet voltage do not match, contact your dealer for

assistance. Do not plug in the power cord.

2. You should use the properly grounded electrical outlet

2.7 Installing the Driver

Please use the cable to connect computer with printer, then turn on the computer and the printer, put the driver CD into the CD-ROM. Install driver by the following ways:

Auto-installing way

Double click the file “Setup.exe” in the driver disc, install driver by the following direct.

Note: Auto-installing way needs the operating system of Windows 2000 or above.

Figure 2-17 Connecting the power cord to the printer

Power supply inlet

Electrical outlet

Power cord

Figure 2-16 Connecting the Ethernet interface cable

Ethernet interface

Ethernet cable

BP-1000K User’s Manual

- 10 -

Hand operated installing way

Note: The hand-operated installing ways of serial interface and parallel interface are the same.

1) The installing steps of parallel interface for Windows 2000/XP/Vista are as follows:

1 Click “Start” → “Settings” → “Select Printers”.

2. Click “Add Printer”, then it pops up a window of “Add Printer Wizard”, click “Next”, then please read the select guide carefully, such as, select “Local printer” in the “Local or Network Printer” window, then click “next”.

3. A window of “Select a Printer Port” pops up, select a usable port. Such as, select “LPT1: (Recommended Printer Port)”, click “Next”.

4. A window of “Install Printer Software" pops up, click “Have Disk...”, click “Next”.

5. A window of “Install From Disk” pops up. Please according to the operating system environment, you should select the path as follow: CD-ROM → “Driver” → “WIN2000 (XP-Vista-Win7)”, click “Open”, then click “OK” to return to the window of “Install Printer Software”, select the respective model, click “Next”.

6. Follow the guide click “Next” gradually till the installation is finished.

2) The installing steps of parallel interface for Windows 7 are as follows:

1. Click “Start” → “Device and Printers”.

3. A window of “Select a Printer Port” pops up, select a usable port. Such as, select “LPT1: (Recommended Printer Port)”, click “Next”.

4. A window of “Install Printer Software” pops up, click “Have Disk...”, click “Next”.

5. A window of “Install From Disk” pops up. Please according to the operating system environment, such as Windows XP operating system, you should select the path as follow: CD-ROM → “Driver” →“WIN2000 (XP-Vista-Win7)”, click “Open”, then click “OK” to return to the window of “Install Printer Software”, select the respective model, click “Next”.

6. Follow the guide click “Next” gradually till the installation is finished.

The USB interface installing steps for Windows 2000/XP/Vista/Win7 are as follows:

The following steps are used Windows XP as example. There are slight differences among different operating systems.

1. Connect the printer to computer with an USB cable and turn on the printer.

2. After the computer find out new hardware and finish searching, pop up a window of “Found New Hardware Wizard”, choose “Install from a list or specific location (Advanced)”, click “Next”.

3. A window of “Found New Hardware Wizard” — “Please choose your search and installation options” pops up, choose “Don't search, I will choose the driver to install”, click “Next”.

4. A window of “Add Printer Wizard” pops up, click “Have Disk...”, click “Browse”.

5. A window of “Install From Disk” pops up. Please according to the operating system environment, you should select the path as follow: CD-ROM → “Driver” → “WIN2000 (XP-Vista-Win7)”, click “Open”, then click “OK” to return to the window of “Add Printer Wizard", select the respective model, click “Next”.

6. Follow the guide click “Next” gradually till

the installation is finished.

The installing steps for Windows 98 are as follows:

(1) The installing steps with a parallel cable or a serial cable:

1. Click “Start” → “Settings” → “Printers”.

BP-1000K User’s Manual

- 11 -

2. Click “Add Printer”, then a window of “Add Printer Wizard” pops up, click “Next”, then please read the select guide carefully, such as, select “Local printer” in the “Local or Network Printer” window, then click “Next”.

3. A window of “Click the manufacturer and model of your printer” pops up, click “Have Disk...”, please click “Browse”, select the path as follow: CD-ROM → “Driver” → “WIN98 (WINME)”, then click “OK”.

4. A window of “Install From Disk” pops up, click "OK, return to a window of “Add Printer”, select the respective model, and then click "Next".

5. A window of “Printer port” pops up, select “Available ports”, such as, select “LPT1: Printer Port”, click “Next”, and then show the printer’s name. If the system is not installed by other printer driver process, the printer is treated as default printer by the application process of Window98 environment, click “Next”. Otherwise according to prompt, choose the printer is default: “Yes”, click “Next”, choose “Yes-(recommended)”, click “Finish”. A window of “Printer test page completed” pops up, click “Yes”.

6. The printer driver process is installed successfully.

(2) The installing steps with an USB cable:

Note: 1. As the system of Windows 98/ME doesn’t have integrated USB driver control, please

install USB driver before using USB interface printing. Then install USB printer driver.

2. If it has installed the USB driver, please install the USB printer driver directly as the following steps.

USB driver installing steps:

1. Connect an USB cable and turn on the printer.

2. After the computer find out new hardware and finish searching, a window of “Add New Hardware Wizard” pops up, click “Next”.

3. A window of “Add New Hardware Wizard” — “Windows operation” pops up, choose “Search the best driver for the device (recommended)”, and click “Next”.

4. A window of “Search for new drivers” pops up, check “Specify a location”, click “Browse”, select the path as follows: CD → ROM → “Driver”-“[WIN98 (WINME) \ USBdriver]”, then click “OK”.

5. Return to a window of “Search for new drivers”, click “Next”; a window of “Windows driver file search for the device” pops up, click “Next”.

6. After the system finishing installing the file automatically, a window of “USB Print Supported” pops up, click "Finish".

7. The printer USB driver process is installed successfully.

USB printer driver installing steps:

1. Click “Start” → “Settings” → “Printers”.

2. Click “Add Printer”, then a window of “Add Printer Wizard” pops up, click “Next”.

3. A window of “Click the manufacturer and model of your printer” pops up, click “Have Disk...”,

please click “Browse”, select the path as follow: CD-ROM → “Driver” → “WIN98 (WINME)”, and then click “OK”.

4. A window of “Install From Disk” pops up, click “OK”, return to a window of “Add Printer”, then click "Next".

5. A window of “Printer port” pops up, select “Available ports”, select “JMUSB”, click "Next", and then show the printer’s name. If the system is not installed by other printer driver process, the printer is treated as default printer by the application process of Window98 environment, click “Next”. Otherwise according to prompt, choose the printer is d

efault: "Yes", click "Next" choose “Yes-(recommended)”, click “Finish”. A window of “Printer test page completed” pops up, click “Yes”.

6. The printer driver process is installed successfully.

BP-1000K User’s Manual

- 12 -

2.8 Network Settings

Please use Jolimark network setting software NetFinder to set the IP address for Jolimark printers, which can be found in the CD or downloaded from www.jolimark.com.

Note: The network printing function needs the operation system of Windows2000 or above.

2.8.1 Connecting Printer

Power on the printer, connect with the Ethernet cable which has been connected to LAN, and look into the information of Ethernet LED indicator to ensure the printer has entered into the normal connection.

2.8.2 Setting IP Address

1. Run NetFinder Software

Double click NetFinder.exe in the PC which connects the printer in the same LAN. The figure of the software is shown as follows:

2. Search printer

Click "Search" button in the main interface, the dialog box appearing would begin searching automatically and show appearance, listing a printer in the main interface if found. The time is counting down in the progress bar (10s in total) and the search would finish as soon as the time is over. When going on searching, press “search” button again.

Yellow LED Green LED Description

ON Blink Connecting to network

OFF OFF Not connecting to network

Button description:

Exit — Exit from the software

Search — Search printers in the same LAN

Assign IP — Modify the IP address and other settings for the specified printer.

BP-1000K User’s Manual

- 13 -

If the printer still can not be found out when the network connection is correct and in the same network, please check whether the network fire wall on the PC open or not. If there is fire wall, please close it temporarily, open again after finishing searching and setting a printer completely.

3. Setting printer’s IP address

The printer’s information is listed in the main interface, the left side of which is the model and description and the right are the IP address and MAC address. What’s more, the assign mode (dynamic/static) is noted behind the IP address.

1) Correlative description for IP address settings

In order to search and set printer’s IP address conveniently for the first time, the factory default

setting is DHCP mode which assigns IP address dynamically. If there is no DHCP server in the connected LAN and printer is set to DHCP mode as well, then it would use the internal pre-set address (IP: 10.0.0.1, Subnet Mask: 255.255.255.0) automatically.

+ 40 hidden pages

Jolimark BP-1000K (Model B) User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual