Instruction Manual
Flexible Impeller Pumps
bronze, high speed
F6B-9
10-24805-01
Read and understand this manual prior to
operating or servicing this product.
IB-519/R01 (1011)
Made in Sweden
Warranty 1 year
INDEX
English ...........................................................................................................................................
For more information about our worldwide locations, approvals, certifications, and local representatives, please visit www.johnson-pump.com. SPX Corporation
reserves the right to incorporate our latest design and material changes without notice or obligation. Design features, materials of construction and dimensional data,
as described in this bulletin, are provided for your information only and should not be relied upon unless confirmed in writing.
3
Original instructionsOriginal instructions
Self-priming, flexible impeller pump of bronze, high
speed
Typical applications
Engine cooling
Design features
Body: Bronze
Impeller: EPDM
Shaft: Stainless steel
The shaft is mounted with two permanently lubricated ball bearings
Seal: Lip seal
Cam: Full
Connection: ø 31,8 mm / 1¼"
Performance curve
0
20
40
60
80 100 120
140
0
1000
2000
3000
4000
5000
6000
50 kPa
100 kPa
150 kPa
200 kPa
250 kPa
4
Original instructionsOriginal instructions
Service instructions
Pos Nos Description Art.no
1 1 Body F6B-9 1/1-CAM 01-24713-1
2 1 Endcover F5B/F6B-9 01-45312-1
3 1 Impeller 08-812B-1
4 1 Gasket F5B/F6B-9 01-45315
5 1 Carrier complete 04-46408-01
5 1 Carrier complete 04-46408-02
6 1 Lip seal 16x28x7 DPSM 0.2233.001
7 2 Ball bearing 6203 2 RS1 ST 0.3431.742
8 1 O-ring 15.3x2.4 0.2173.402
9 4 Screw M5x8 DIN933 Slotted brass 0.0141.502
10 1 Washer F5B/F6B/F7B 01-45680
5
Original instructionsOriginal instructions
Disassembly
1. Remove the endcover and the gasket.
2. Pull out the impeller using two screw drivers or other suitable implements.
3. Remove the lip seal.
4. Remove the shaft with ball bearings by pressing on the shaft end from the
impeller side.
5. Remove the ball bearings. Do not press the ball bearings over the sealing
surface.
6. Remove the o-ring from the shaft.
Assembly
1. Mount the ball bearings on the shaft. Do not press the ball bearings over the
sealing surface.
2. Mount the o-ring on the shaft.
3. Press the shaft with ball bearings into the body.
4. Mount the lip seal (spring towards the impeller).
5. Lubricate the impeller with JP Impeller Lubricant and fit it with a rotating
movement in the intended direction of rotation.
6. Fit the gasket before mounting the endcover.
Waste handling material recycling
At the products end of life, please dispose of the product according to applicable
law. Where applicable, please disassemble the product and recycle the parts
material.
6
Original instructions
A
A
48
ø
33,3 (2x)
ø
31,8 (2x)
5,6
63
60
15
19,1
5/16-18 UNC
15
ø
ø
82,5
ø 87,88
ø 88,9
120°
(2x)
ø 15,9(4x)
ø
13 (3x)
ø
60,496
60,45
108-ø
10
16,5
82
92,2
124
1
2 34 56789
Märkning på lock.
Mark on endcover.
10
6,4
60°
30°
60°
SPX Flow Technology
SPX Flow Technology Örebro AB
Nastagatan 19, P.O. Box 1436
SE-701 14 Örebro, Sweden
Phone: +46 (0)19 21 83 00 Fax: +46 (0)19 27 23 72
E-mail: johnson-pump.marine@spx.com
For more information about our worldwide locations, approvals, certifications, and local representatives, please visit
www.johnson-pump.com and www.spxft.com.
SPX Corporation reserves the right to incorporate our latest design and material changes without notice or obligation.
Design features, materials of construction and dimensional data, as described in this bulletin, are provided for your
information only and should not be relied upon unless confirmed in writing.
Copyright © 2009, 2010 SPX Corporation
Loading...