Johnson Level 40-6210 User Manual

Green Laser Technology™

ob up or dow

p

PowerLine™ Magnetic-Laser “Sheave Alignment System”

Instructions

The PowerLine™ Sheave Alignment System aligns belts, pulleys, sheaves, sprockets, gear trains, rollers,
platforms, conveyors, and other plant equipment. Its purpose is to replace often times inaccurate and time­consuming straightedge and string alignment methods currently in use. Compared to these older methods,
the PowerLine™ is easier, faster, and more accurate. With the PowerLine™, you will greatly reduce
downtime and belt failures. The new Green Laser Technology™ and reflective target system increases the
brightness of the laser line by 10 fold. This means that the system can be used in direct sunlight and at
longer distances.

Component Descriptions: The PowerLine™ Sheave Alignment System includes a laser line emitter and
three grooved targets. All components are especially rugged for long life and are shipped in a sturdy
storage case.

Laser Line Emitter: Its bottom machined surface mounts magnetically to the machined face of sheave,
gear, etc. It projects a 1/16” thick laser reference line over a wide angle. The projected reference line is
parallel to the machined bottom surface and offset from it by 0.312”.

Warning and Certification Label Bottom Surface is on Back Side

Level Vial Product Identification Battery Cap
Label On/Off Switch

Laser Safety: Caution- Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.

The PowerLine™ emitter uses a laser diode with a maximum output power of less than <1 milliwatt @ 635
nm. The laser classification is Class II < 1mW @ 532nm with only minor precautions required. Never
stare directly into the laser transmitter or aim the laser into someone’s eyes. The PowerLine™ complies
with 21CFR parts 1040.10 and 1040.11.

Grooved Targets:

Excellent alignment is achieved when laser
line hits here on center of target groove. This
reference can be adjusted up or down to
compensate for sheaves with different thickness
by turning knob.

Knob on to

5/16”

0.312” 1/16”

Initial knob setting is to
extend the magnet bottom
outward from the target
bottom by one full turn
(1/16”) so target groove
center is elevated 0.312”
off magnet bottom. Adjust
kn

n from this

2

Three cylindrical grooved targets mount magnetically to the machined face of the companion pulley,
sheave, gear, etc. to be aligned. The targets track the position of the machined face relative to the laser
reference line emitted by the PowerLine™ laser. Excellent alignment is achieved when the laser line
strikes the center of the cylindrical grooves on all three targets simultaneously. Note, as a visual aid, when
the laser strikes the target center, it gives a brighter reflection than when the laser strikes the V shaped
sides.

The offset between the center of the target groove and the magnetic bottom of the target is adjustable to
compensate for differences in pulley endwall thickness, belt wear, and groove wear. Turn the knurled knob
on the top of the target to make adjustments either up or down. As marked on top, one full turn of the knob
moves the target center up or down 1/16”. The initial knob setting is to extend the magnet bottom outward
from the bottom of the target bottom by one full turn (1/16” extended) so that the target center is 0.312”
away from the magnetic bottom. (See sketch on previous page.) For example, it is very common to find
pulleys of smaller diameter to have thinner rims than pulleys of larger diameter. During setup, measure this
difference using a dial caliper or equal means. Prior to mounting the targets, adjust the knobs of all three
target to compensate for the measured difference. When the laser is on the smaller pulley, the offset will be
reduced from initial setting of 0.312 by turning knob CCW.

Optional Belt Tension Testers:

Each PowerLine™ kit can include two (2) Kricket© belt tension testers. Combined, they cover a belt
tension range from 30 Lbs. to 300 pounds of tension. Separate instructions for these testers are included
with each Krikit© accessory. As a general rule of thumb, the deflection force tension specification given
by belt manufacturers must be multiplied by 16 to give proper Kricket© tension value. Use the Kricket©
tester based on this calculation. During tensioning, use the PowerLine™ laser to monitor and correct
alignment.

PowerLine™ Laser Sheave Alignment Tool Alignment and Tensioning Procedure

1. Prerequisites

Caution:

Lock out and tag out equipment before you start work.

Follow all applicable plant procedures.

• Inspect machinery bases and foundation for deterioration, looseness, and cracking.

• Check all base bolts for correct torque and eliminate any soft foot conditions.

• Remove belt guards as needed for access.

• Check sheaves and belts for wear. Replace as necessary.

• Check each shaft’s runout with a dial indicator. Excessive runout implies shaft or bearing problems.

• Check sheave side wobble and runout with a dial indicator. Stay within sheave manufacturer’s

guidelines.

• Install V-belts onto sheaves.

2. Compensate For Sheave Endwall Thickness Difference and Mount Laser and Targets

2