Page 1
SINGLE DUCT VAV TERMINALS
INSTALLATION, OPERATION & MAINTENANCE
New Release
MODELS TSS & TSL
TSS
Form 130.13-NOM1 (114)
TSL
Page 2
FORM 130.13-NOM1 (114)
TABLE OF CONTENTS
SAFETY CONSIDERATIONS ........................................................................................................................3
INSPECTION .................................................................................................................................................4
STORAGE .....................................................................................................................................................4
PRE-INSTALLATION INSPECTION ..............................................................................................................5
SEQUENCE OF OPERATION .......................................................................................................................5
Single Duct .............................................................................................................................................5
INSTALLATION .............................................................................................................................................5
Clearances .............................................................................................................................................5
Hanging and Mounting Equipment ......................................................................................................5
Unit Weights ...........................................................................................................................................6
Duct Connections
Critically Sound Applications
Coil Connections ...................................................................................................................................7
Electrical .................................................................................................................................................7
OPERATION ..................................................................................................................................................7
Start-Up ..................................................................................................................................................7
3 Phase Balancing .................................................................................................................................7
MAINTENANCE ............................................................................................................................................8
Optional Damper Actuator ....................................................................................................................8
Manual Override ....................................................................................................................................8
Mechanical Angle of Rotation Stops ...................................................................................................8
External Terminal Strip .........................................................................................................................8
Overload Protection ..............................................................................................................................8
Checkout Instructions ...........................................................................................................................8
Damper Shaft .........................................................................................................................................8
Coil ..........................................................................................................................................................8
Cleaning ............................................................................................................................................9
Electric Heat ..........................................................................................................................................9
Minimum Operating Conditions ......................................................................................................9
Electric Heater Rack Replacement .................................................................................................9
Electric Heater Element Replacement ............................................................................................9
Heater Troubleshooting Guide ......................................................................................................10
(SSR) Troubleshooting Guide .......................................................................................................11
..................................................................................................................................6
...............................................................................................................7
Calibration Charts ...............................................................................................................................15
2
JOHNSON CONTROLS
Page 3
FORM 130.13-NOM1 (114)
SAFETY SYMBOLS
The following symbols are used in this document to alert the reader to areas of potential hazard:
DANGER indicates an imminently
hazardous situation which, if not
avoided, will result in death or serious
injury.
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or se-
rious injury.
SAFETY CONSIDERATIONS
The equipment covered in this manual is designed for
safe and reliable operation when installed and operated
within its’ design specication limits. To avoid personal
injury or damage to equipment or property while
installing or operating this equipment, it is essential
that qualied, experience personnel familiar with local
codes and regulations, perform these functions using
good judgment and safe practices. See the following
cautionary statements.
ELECTRICAL SHOCK HAZARDS
All power must be disconnected prior
to installation and servicing this equip-
ment. More then one source of power
may be present. Disconnect all power
sources to avoid electrocution or shock
hazards.
HOT PARTS HAZARD
Electric resistance heating elements
must be disconnected prior to servicing. Electric heaters may start auto-
matically; disconnect all power and
control circuits prior to servicing to
avoid burns.
Check that rigging and lifting equipment can safely support the unit as-
sembly and component weights.
CAUTION identies a hazard which
could lead to damage to the machine,
damage to other equipment and/or
environmental pollution. Usually an
instruction will be given, together with
a brief explanation.
NOTE is used to highlight additional
information which may be helpful to
you.
All assemblies must be adequately
secured during lifting and rigging by
temporary supports and restraints un-
til equipment is permanently fastened
and set in its’ nal location.
All unit temporary and permanent
supports must be capable of safely
supporting the equipment’s weight and
any additional live, seismic or dead
loads that may be encountered. All
supports must be designed to meet ap-
plicable local codes and ordinances.
All fastening devices must be designed
to mechanically lock the assembly in
place without the capability of loosen-
ing or breaking away due to system
operation and vibration.
Secure all dampers when servicing
damper, actuators or linkage. Dampers may activate automatically, discon-
nect the control circuits or pneumatic
control systems to avoid injury.
Protect adjacent ammable material
when brazing. Use ame and heat
protection barriers where needed.
Have re extinguisher ready for im-
mediate use.
JOHNSON CONTROLS
3
Page 4
FORM 130.13-NOM1 (114)
INSPECTION
Upon receipt of equipment, carefully check all items
against the bill of lading to ensure that all equipment has
been received (including shipped loose items). Note any
discrepancy on the bill of lading before signing.
Inspect all equipment for any signs of damage caused
during transit. On units with re-heat, check the coil
ns and/or ensure that the resistance heat coils are
not damaged. Note any visual damage on the bill of
lading before signing. Immediately report all visual
and concealed damage to the carrier and le a claim
with the carrier.
Locate the model number on the nameplate and check
that the correct units have been received. Verify that all
options have been included, such as controls, heating
coils, etc. Also ensure that unit voltage agrees with the
building parameters. If a discrepancy is discovered
between what was ordered and received, contact your
local Johnson Controls representative immediately.
DO NOT USE FLOW SENSOR,
CONNECTING TUBES, COIL STU-
BOUTS OR DAMPER SHAFT AS
A HANDLE WHEN LIFTING OR
MOVING EQUIPMENT, AS DAM-
AGE MAY OCCUR.
DO NOT HANDLE EQUIPMENT’S
HEATING ELEMENTS, AS PERMA-
NENT DAMAGE MAY OCCUR.
DO NOT work on damper until associ-
ated actuator is disconnected.
NEVER pressurize equipment above
specied test pressure.
PROTECT adjacent ammable ma-
terials when brazing. Use ame and
heat protection barriers where needed.
Have a re extinguisher at hand and
ready for immediate use.
STORAGE
If equipment is to be stored prior to installation, observe
the following precautions:
1. Choose a dry storage site that is reasonably level
and sturdy to prevent undue stress or permanent
damage to the equipment. Set equipment off
ground if in moisture prone areas.
2. Tag and store in a safe place until needed. Cover
entire equipment with protective tarp or moisture
proof cover. Extend cover under equipment if
stored on ground. Secure cover with adequate tie
downs and store indoors. Be sure that piping connections have protective shipping caps installed.
CHECK assembly and component
weights to be sure that the rigging
equipment can handle them safely.
Note; also check the centers of gravity
and any specic rigging instructions.
CHECK for adequate ventilation
so fumes do not migrate through
ductwork to occupied spaces when
welding or cutting around the unit.
4
JOHNSON CONTROLS
Page 5
FORM 130.13-NOM1 (114)
PRE-INSTALLATION INSPECTION
DO NOT USE FLOW SENSOR,
CONNECTING TUBES, COIL STU-
BOUTS OR DAMPER SHAFT AS
A HANDLE WHEN LIFTING OR
MOVING EQUIPMENT, AS DAM-
AGE MAY OCCUR.
DO NOT HANDLE EQUIPMENT’S
HEATING ELEMENTS, AS PERMA-
NENT DAMAGE MAY OCCUR.
Ensure that all linkages are connected properly. Check
the linkage that connects the actuator to the damper shaft
to ensure that the nuts are tight.
While viewing the damper from the discharge of the
unit, rotate the shaft fully. The damper should close
fully and there should be no gaps between the damper
gasketing and the inside of the valve.
INSTALLATION
DO NOT USE FLOW SENSOR,
CONNECTING TUBES, COIL STU-
BOUTS OR DAMPER SHAFT AS
A HANDLE WHEN LIFTING OR
MOVING EQUIPMENT, AS DAM-
AGE MAY OCCUR.
DO NOT HANDLE EQUIPMENT’S
HEATING ELEMENTS, AS PERMA-
NENT DAMAGE MAY OCCUR.
All terminal equipment with electric heaters must
be installed in a horizontal plane with respect to the
airow stream. Low height equipment (Model TSL)
can be ipped over in the eld to vary or change control
section handing.
Clearances
SEQUENCE OF OPERATION
Single Duct
The basic unit consists of a sheet metal casing and an air
valve, which is used to modulate the air being delivered
into the occupied zone. Air enters the air valve inlet
and exits into the sheet metal casing to be distributed
to the occupied zone through ductwork attached to the
discharge of the unit.
The basic unit can be ordered with either a factory
mounted hot water heating coil or an electric heater.
These re-heat units are used primarily to reheat the
air-to-zone temperature when the load in the occupied
space drops off.
The primary air is modulated through the FlowStar™
air valve by rotating the damper blade. The air valves
come in rectangular and round. The round valves only
come in diameters of 4, 5, 6, 8, 10, 12, 14 and 16 inches;
an adapter must be used for metric ductwork.
All equipment covered in this document, including those
with electric heat, are ETL listed for 0.0" clearance to
combustibles. Refer to NEC and/or local codes for
minimum electrical clearances required for service.
Equipment should not make contact with any structure
located above the equipment without appropriate
isolation. Equipment supplied with bottom access
panels requires sufcient clearance to access fasteners,
and to lower and slide panel horizontally until clear of
bottom of unit.
Hanging and Mounting Equipment
Although the basic equipment is generally light enough
that it can be supported by the ductwork, Johnson
Controls strongly recommends that all equipment be
suspended from the upper most ceiling or a structural
element of the building, independent of the false ceiling
grid. Suspension devises are eld supplied, sized and
designed by others. Johnson Controls will not accept
responsibility for unit support. Equipment must be
installed in a level horizontal plane. Failure to level
equipment properly may prevent proper operation of
controls. Provisions for proper support in seismically
active regions is the responsibility of others. See table
1 through 4 for unit weights.
JOHNSON CONTROLS
5
Page 6
UNIT WEIGHTS
FORM 130.13-NOM1 (114)
TABLE 1 - SINGLE DUCT TERMINAL UNIT WEIGHTS
UNIT
SIZE
SINGLE
04 20 (9) 25 (11) 35 (16) 50 (23) 64 (29) 79 (36)
05 20 (9) 25 (11) 35 (16) 50 (23) 64 (29) 79 (36)
06 19 (9) 24 (11) 34 (15) 49 (22) 62 (28) 77 (35}
08 20 (9) 26 (12) 37 (17) 53 (24) 71 (32) 87 (39)
10 25 (11) 32 (15) 44 (20) 62 (28) 78 (35) 96 (44)
12 28 (13 36 (16) 50 (23) 71 (32) 89 (40) 110 (50)
14 35 (16) 44 (20) 59 (27) 84 (38) 106 (48) 131 (59)
16 37 (17) 47 (21) 63 (29) 90 (41) 113 (51) 140 (64)
19 49 (22) 62 (28) 85 (39) 120 (55) 141 (64) 176 (80)
22 51 (23) 65 (29) 90 (41) 127 (58) 148 (67) 185 (84)
TSS TSS w/ SA TSS w/ EH
SINGLE
WALL
DOU-
BLE
WALL
SINGLE
WALL
DOU-
BLE
WALL
WALL
DOU-
BLE
WALL
TABLE 3 - SINGLE DUCT LOW HEIGHT TERMINAL UNIT
WEIGHTS
UNIT
SIZE
SINGLE
10 26 (12) 30 (14) 43 (19) 58 (26) 62 (28) 77 (35)
12 28 (13) 35 (16) 49 (22) 68 (31) 74 (34) 93 (42)
14 39 (18) 47 (21) 62 (28) 82 (37) 90 (41) 110 (50)
16 45 (20) 55 (25) 73 (33) 96 (44) 103 (47) 126 (57)
TSL TSL w/ SA TSL w/ EH
WALL
DOUBLE
WALL
SINGLE
WALL
DOUBLE
WALL
SINGLE
WALL
DOUBLE
WALL
TABLE 2 - TSS WATER COIL WEIGHT ADDS
UNIT
SIZE
04 4 (2) 5 (2) 8 (4) 12 (5)
05 4 (2) 5 (2) 8 (4) 12 (5)
06 4 (2) 5 (2) 8 (4) 12 (5)
08 4 (2) 6 (3) 9 (4) 13 (6)
10 5 (2) 8 (4) 12 (5) 18 (8)
12 7 (3) 10 (5) 16 (7) 22 (10)
14 9 (4) 14 (6) 21 (10) 30 (14)
16 10 (5) 16 (7) 24 (11) 34 (15)
19 12 (5) 20 (9) 28 (13) 40 (18)
22 13 (6) 22 (10) 32 (15) 44 (20)
Adds for water coils reect actual operating weight.
1 ROW 2 ROW 3 ROW 4 ROW
# OF ROWS
TABLE 4 - TSL WATER COIL WEIGHT
ADDS
UNIT
SIZE
Adds for water coils reect actual operating weight.
1 ROW 2 ROW 3 ROW 4 ROW
10 9 (4) 12 (5) 15 (7) 18 (8)
12 11 (5) 15 (7) 19 (9) 23 (10)
14 13 (6) 18 (8) 22 (10) 27 (12)
16 15 (7) 21 (9) 27 (12) 32 (15)
# OF ROWS
When requested, equipment is supplied with optional
hanger brackets for use with up to a 3/8" diameter
hanger rod. See submittal drawings for hanger bracket
locations.
Hanger straps may be utilized as an alternate means of
suspending the equipment. Do not secure hanger straps
to electric heaters, coils or control enclosures. Hanger
straps can be mounted directly to the sides and bottom
of equipment casing, such that they do not interfere with
working components or access panels, using screws that
do not penetrate the unit cabinet more than 3/8".
When hanging equipment, always use the support
method as prescribed for rectangular duct in the job
specications.
Duct Connections
When fastening ductwork to equip-
ment, DO NOT use fasteners that
penetrate equipment cabinet more
than 3/8" [10mm]. Fasteners penetrating the equipment cabinet over 3/8"
[10mm] may come in contact with live
electrical parts or penetrate other com-
ponents within the equipment casing
causing damage.
All duct connections should be congured and installed
in accordance with SMACNA guidelines and all local
code requirements.
6
JOHNSON CONTROLS
Page 7
FORM 130.13-NOM1 (114)
Allow a minimum of 1½-duct diameters of straight
duct prior to equipment inlet and equipment discharge.
The diameter of the inlet duct for round valves must
be equal to the listed size of the equipment. The round
air valve inlet collar of the equipment is 1/8" smaller
then listed size in order to allow the round ductwork to
slip over the air valve inlet collar. DO NOT INSERT
DUCTWORK INTO AIR VALVE INLET COLLAR.
When making ductwork connection to air valve inlet
collar and insulating air valve inlet, take caution not to
damage or remove the ow sensor connections, which
are vital to unit control. Provide insulation around entire
inlet collar (all the way to the equipment casing).
Permissible discharge duct connections are straight
anged, slip and drive or drive and screw.
If equipment is to be installed in a location with high
humidity, external insulation around the heating coil
should be installed.
Sound Critical Applications
Flexible duct connectors are not recommended on
equipment discharge. The sagging membrane of these
ttings can cause turbulence and higher air velocities
that generate noise. Also, lightweight membrane
material allows noise to breakout, which can increase
sound levels in the space below.
Coil Connections
Hot water and steam coils are male sweat connections.
Use appropriate brazing alloy for system temperature
and pressure. Refer to unit construction submittal
drawing for specic connection size. MAXIMUM
HYDRONIC SYSTEM OPERATING PRESSURE
MUST NOT EXCEED 300 PSIG. MAXIMUM
STEAM SYSTEM PRESSURE MUST NOT EXCEED
15 PSIG.
Minimum circuit ampacity (MCA) designates the
maximum operating load of the equipment for sizing
wire feeders. Fuse size of the internal fuse if supplied.
Maximum Overcurrent Protection (MOP) designates
the largest breaker or fuse in the electrical service panel
that can be used to protect the equipment.
Use Copper conductors only.
OPERATION
Start-Up
Thorough safety precautions should always be taken
when performing startup and service. Only qualied
individuals should perform these tasks.
Check that all electrical work is nished and properly
terminated. Check that all electrical connections are
tight and that the proper voltage is connected.
3 Phase Balancing
AC power imbalance must not exceed 2%. Be sure that
the following guides are met:
1. AC power is within 10% of rated voltage at rated
frequency. (See equipment nameplate for rat-
ings).
2. AC power is within 5% of rated frequency at rated
voltage.
3. A combined variation in the voltage and frequency
of 10% (sum of absolute values) of rated values,
provided the frequency variation does not exceed
5% of rated frequency.
Equipment with electric heat requires
a minimum of 0.1" w.g. downstream
static pressure.
Electrical
All eld wiring must comply with NEC and all local
codes. Electrical and/or control wiring diagrams are
located on the control enclosure box. All electric heaters
are staged per specications.
The installing electrician should rotate the incoming
electric service by phase to help balance the building
electrical load.
JOHNSON CONTROLS
Prior to start-up, the project control sequence/wiring
diagram should be obtained and thoroughly understood.
If factory supplied analog or DDC controls are utilized,
refer to the applicable Operation Manual for start-up
and balancing information.
7
Page 8
FORM 130.13-NOM1 (114)
MAINTENANCE
Optional Damper Actuator
An optional factory mounted oating type actuator
is available, which mounts directly to the damper
operating shaft. The actuator is not provided with and
does not require any limit switches but is electronically
protected against overload.
Manual Override
A button on the side of the actuator cover disengages
the gear train so the drain shaft can be moved manually.
Releasing the button will re-engage the gear train.
Mechanical Angle of Rotation Stops
The adjustable stops may be field adjusted to halt
the rotation of the damper blade before the damper
blade reaches the damper stops. The actuator can be
indenitely stalled in any position without harm.
1. Loosen the two end stop screws using a No. 2
Phillips head screwdriver, being careful not to
unscrew the captive nut under the slot.
2. Move the stops (in 2.5° steps) to the desired position and retighten the screws.
External Terminal Strip
Checkout Instructions
1. Disconnect actuator from the controller.
2. Apply 24 VAC to the COM and CW terminals on
the actuator. Actuator should rotate in a clockwise
direction.
3. Apply 24 VAC to the COM and CCW terminals on
the actuator. Actuator should rotate in a counter
clockwise direction.
4. If actuator moves in both directions, it is operational.
5. If the actuator does not rotate, it may be at an end
stop or there is a problem with the damper.
6. Loosen the set screw to free the actuator from the
damper shaft. Check to make sure that the damper
shaft rotates freely.
7. Check to make sure that actuator is not against
stop. Repeat steps 2 and 3.
8. If actuator does not rotate, replace.
Damper Shaft
There is an indicator on the end of the damper shaft that
can be used to determine the position of the damper
blade. If the indicator is horizontal, the damper is
completely open. The damper shaft is ½" diameter.
The external terminal strip is located on the top of the
actuator. Connections are numbered. The terminals
are designed for 26 to 16 gauge wires. For most
installations, 18 or 16 gauge wire will work well with
the actuator (see table 5 for maximum wire lengths).
TABLE 5 - MAXIMUM WIRE LENGTHS
WIRE SIZE MAX FEET
16 GA 1225 FT
18 GA 725 FT
20 GA 400 FT
22 GA 200 FT
Overload Protection
The actuators are electronically protected against
mechanical overload. In the actuator, an electronic
circuit maintains the current at a level that will not
damage the motor while providing adequate holding
torque.
Coil
The frequency of required cleaning is dependent on the
operating hours of the system, lter maintenance and
efciency as well as dirt load.
Important: Coils may become externally dirty as result of normal opera-
tion. Dirt on the surface of the coil
reduces its ability to transfer heat that
can result in reduced performance,
and increased operating energy cost.
If the dirt on the surface of the coil
becomes wet, microbial growth (mold)
can result, possibly causing unpleas-
ant odors and serious health related
indoor air quality problems.
Fin edges are sharp. Fins are fragile;
care must be exercised to avoid damag-
ing ns. Do not use solutions to clean
coils; drain pans are not present to
remove collected solution.
8
JOHNSON CONTROLS
Page 9
FORM 130.13-NOM1 (114)
Cleaning
1. Disconnect all electrical power to the equipment,
tag and lock out power source.
2. Gain access to coil either through ductwork or
optional coil access panel.
3. Use soft brush and vacuum to remove loose debris
from sides of coil. Do not use uid or solvents to
clean coils, as no provisions for collecting liquids
exist on this type of equipment.
4. Straighten any coil ns that may have been damaged during cleaning process with n comb.
5. Replace ductwork or access panel and restore
electrical power to equipment.
Electric Heat
Johnson Controls electric heaters require little or no
maintenance.
Electric heaters come equipped with a primary auto-reset
limit switch. These limit switches provide protection
against overheating. The auto-reset limits switches
automatically cut the heater off when overheating
occurs, and turns the heater back on when the elements
have cooled down. Electric heaters also come equipped
with a secondary one-time trip limit switch. Should
the secondary limit switches trip, they will need to
be replaced with a limit switch that has the same trip
temperature as the one-time trip limit switch that was
originally supplied with the electric heater. An optional
manual reset secondary is available, which can be reset
by depressing the reset switch.
Minimum Operating Conditions
Airow must be at least 70 CFM per kW. A minimum
of 0.1" w.g. external pressure is required.
Electric Heater Rack Replacement
JOHNSON CONTROLS HEATERS
1. Turn off power supply before servicing.
2. Locate T-Plate inside on heater control enclosure.
3. Before removing wires from the element rack
T-Plate, mark where the wires are connected so
that they can be reconnected correctly on the new
element rack.
4. Remove the wires and screws holding the heater
T-plate in the control enclosure and remove element rack.
5. Insert new element rack into control enclosure and
replace screws to secure the element rack to control
enclosure.
6. Replace wires.
7. Close control enclosure cover before turning on
the power.
Electric Heater Element Replacement
TUTCO HEATERS
1. Turn off power supply before servicing.
2. Disconnect eld wiring from Electric Heater Control Enclosure.
3. Disconnect Amp Plug Connectors if equipped.
4. Remove 4 mounting screws from inside Electric
Heater Control Enclosure.
5. Slide entire heater assembly out of Single Duct
Terminal.
6. Remove wires and any jumpers from heater ele-
ment terminal ends, noting which wire and jumper
goes to which terminal.
7. Remove ¼" hex head screws located near terminal
ends.
8. Remove ¼" hex head screws from opposite of
terminal end on heater rack.
9. Remove elements and replace with new ones.
10. Reassemble, replace wires correctly.
11. Close control enclosure cover before turning on
power.
JOHNSON CONTROLS
9
Page 10
ELECTRIC HEATER TROUBLESHOOTING GUIDE
FORM 130.13-NOM1 (114)
TABLE 6 - HEATER TROUBLESHOOTING GUIDE
Check wiring diagrams to ensure that heater is properly wired.
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
HEATER DOES NOT OPERATE
LOW OR HIGH TEMPERATURE RISE
SHORT CYCLING
HEATER WITH SSR DOES NOT
OPERATE
JOHNSON CONTROLS AND TUTCO
No Power Check Disconnect.
Check Control Signal (i.e. 24 VAC).
No Control Voltage
Blown Fuse Replace fuse.
Open Limit (primary or secondary)
Airow Incorrect Direction Check sensing tube, rotate if needed.
Low Airow Static Pressure Increase airow.
Damaged Elements
Incompatible Thermostat or Controller
Problems with Additional Stages
Incorrect CFM
Improper Airow
Low CFM
Incorrect Signal Applied Verify signal input.
Interface Board Fuse Blown Replace fuse.
See SSR Troubleshooting (next page)
Check transformer and transformer fus-
ing (if applicable), replace if necessary.
Replace limits or reset as applicable.
Check for continuity across limit to de-
termine if open, replace as necessary.
Check for open or damaged elements
and replace as necessary.
Check Wiring.
Check for compatibility.
Check location of thermostat; may be
installed in a “too hot” or “too cold loca-
tion. Check heat outputs on controller.
Check contactors for open coil.
Check for damaged elements.
Check for blocked duct or location of
heater.
Check for even airow across the face
of the element section.
Check for blocked duct.
Verify installation per SMACNA and
ASHRAE guidelines.
Check for dirty lters.
See remedies for “Improper Airow”.
Check air velocity of 70 CFM per kW.
10
JOHNSON CONTROLS
Page 11
PROPORTIONAL HEAT CONTROL
(SSR) TROUBLESHOOTING GUIDE
Johnson Controls Heaters
FORM 130.13-NOM1 (114)
Lethal voltages are present in the
heater control enclosure. Use extreme
caution when taking measurements in
these units. Always disconnect power
before removing or re-applying any
connections.
1. Before applying power, verify wiring matches
diagram in cover of heater control enclosure, and
that correct line voltage has been wired to heater
line block.
2. Verify 24 VAC +15% or -10% between P1 and P2
of interface circuit board (ETPHCI, ETPHCV2,
etc., depending on input).
3. The table below lists responses to input signal by
interface model as explained in step 4. If any of
these inputs cannot be obtained, refer to the literature on the device that is supposed to provide the
input. Otherwise, proceed to step 4.
INTERFACE
MODEL
ETPHCI 12.0 mA 4.0 mA 20.0 mA Sig, Com
ETPHCV2 6.0 VDC 2.0 VDC
ETPHCC 50% 0 VAC 24 VAC Sig, Com
ETPHCC1 50% 0 VAC 24 VAC
“PULSE”
INPUT
FULL
OFF
INPUT
4. Apply Full Off Input per table above. If the unit
is three phase, verify that the LED on the SSR
(solid state relay) is off. If the unit is single phase,
measure voltage between P4 and P6 and verify 0.3
VDC + or - 0.3 VDC. Replace the interface circuit
board if the voltage is higher than specied, or the
LED is on.
5. Apply Full On Input per table above. If the unit is
three phase, verify that the LED on the SSR (solid
state relay) is on. If the unit is single phase, measure voltage between P4 and P6 and verify between
3 and 5 VDC.
FULL
ON
INPUT
10.0
VDC
INPUTS
Sig, Com
+18,
Com
6. If the module provided is an ETPHCC or ETPHCC1, go to step 7. Apply “Pulse” Input per
table above. If the unit is three phase, verify that
the LED on the SSR (solid state relay) is ashing
at an interval of about one second. If the unit is
single phase, the voltage between P4 and P6 of the
interface board should vary between the Full Off
and Full On voltages in steps 4 and 5 in intervals
of about one second.
Some voltmeters will not respond this
quickly, so the value of the voltages
may not appear to be correct; however,
if the voltage appears to be changing
at regular intervals, it may be as-
sumed that this function is operating
properly.
This completes the low voltage portion of the unit
test. Go to step 8.
7. For the ETPHCC or ETPHCC1, the associated
consignment controller must be directed to output
a 50% On pulse width modulation signal. For three
phase, verify that the LED is pulsing at regular
intervals. The rate of the pulse is based on the
output from the consignment controller. If the unit
is single phase, the DC voltage between P4 and P6
of the interface board should vary between the full
Off and full On voltages in steps 4 and 5.
Some voltmeters will not respond this
quickly, so the value of the voltages
may not appear to be correct; however,
if the voltage appears to be changing
at regular intervals, it may be as-
sumed that this function is operating
properly.
JOHNSON CONTROLS
11
Page 12
8. If the heater always remains energized when power
is applied, remove the wire from P4 of the interface
circuit board. If the heat remains on, there is a
wiring error or the SSR is defective.
Remove Power From the Unit Before
Proceeding With the Next Step.
9. If the heater is always de-energized when power
is applied, remove the line and load connections
to the proportional heat control and temporarily
tie them together. If the system is a three phase
arrangement, do the phases one at a time.
Always remove power from the unit
before moving to the next phase).
FORM 130.13-NOM1 (114)
Make sure there is no danger of the temporary
connection shorting to another component or the
chassis. Briey reapply power. If the section of
heat under test now energizes, the SSR is defective.
If heater still will not energize, one of the heater
safety devices (limits, safety contactor or airow
switch) or elements is defective.
12
JOHNSON CONTROLS
Page 13
PROPORTIONAL HEAT CONTROL
(SSR) TROUBLESHOOTING GUIDE
Tutco Heaters, All Power Modules
FORM 130.13-NOM1 (114)
JOHNSON CONTROLS
13
Page 14
FORM 130.13-NOM1 (114)
PROPORTIONAL HEAT CONTROL
(SSR) TROUBLESHOOTING GUIDE
Tutco Heaters, R820 SCR’s
14
JOHNSON CONTROLS
Page 15
CALIBRATION CHARTS
Flow Star Calibration Chart
Model TSS
FlowStar Calibration Chart
(For dead-end differential pressure transducers)
FORM 130.13-NOM1 (114)
Model TSS
400 SERIES
(PNEUMATIC)
STANDARD CON-
UNIT
SIZE
4 43 250 35 250 30 43 55 250 250
5 68 350 50 350 48 65 88 350 350
6 75 490 60 550 53 75 97 435 530
8 145 960 115 1000 105 145 190 840 1000
10 235 1545 185 1600 165 235 305 1355 1600
12 340 2250 285 2300 240 340 440 1975 2300
14 475 3100 390 3100 335 475 615 2750 3100
16 625 4100 520 4100 440 625 805 3595 4100
19 1180 6500 1025 6500 845 1180 1510 6375 6500
22 1730 8000 1450 8000 1260 1730 2200 8000 8000
Notes:
1. Minimum and maximum airow limits are dependent on the specic DDC controller supplied. Contact the control vendor to obtain the
minimum and maximum differential pressure limits (inches w.g.) of the transducer utilized with the DDC controller.
2. Maximum CFM is limited to value shown in General Selection Data.
3. FlowStar™ differential pressure tubing connections: High side indicated by red tubing; Low side indicated by black tubing.
4. Electric heat will not operate below 0.03” w.g. differential pressure
JOHNSON CONTROLS
TROLLER
MIN. MAX. MIN. MAX.
7000 SERIES
ANALOG
ELECTRONIC
DDC CONSIGNMENT CONTROLS
(See Notes Below)
MIN. MAX.
Min. transducer differential
pressure (in. w.g.)
0.015 0.03 0.05 1.0 ≥1.5
Max. transducer differential
pressure (in. w.g.)
15
Page 16
FlowStar Calibration Chart
(For dead-end differential pressure transducers)
Model TSL
NOTE: Maximum and minimum CFM limits
are dependent on the type of controls that are
utilized. Refer to the table below for specic
values. When DDC controls are furnished by
others, the CFM limits are dependent on the
specic control vendor that is employed. After
obtaining the differential pressure range from
the vendor, the maximum and minimum CFM
limits can be obtained from the chart to the left
(many controllers are capable of controlling
minimum setpoint down to 0.015”w.g.)
400 SERIES
(PNEUMATIC)
STANDARD
UNIT
SIZE
10 235 1545 170 1600 170 235 305 1370 1600
12 340 2250 240 2300 240 340 435 1955 2300
14 495 3100 350 3100 350 495 640 2855 3100
16 660 4100 465 4100 465 660 850 3800 4100
Notes:
1. Minimum and maximum airow limits are dependent on the specic DDC controller supplied. Contact the control vendor to obtain the
minimum and maximum differential pressure limits (inches w.g.) of the transducer utilized with the DDC controller.
2. Maximum CFM is limited to value shown in General Selection Data.
3. FlowStar™ differential pressure tubing connections: High side indicated by red tubing; Low side indicated by black tubing.
4. Electric heat will not operate below 0.03” w.g. differential pressure
CONTROLLER
MIN. MAX. MIN. MAX.
7000 SERIES
ANALOG
ELECTRONIC
DDC CONSIGNMENT CONTROLS
(See Notes Below)
MIN. MAX.
Min. transducer differential
pressure (in. w.g.)
0.015 0.03 0.05 1.0 ≥1.5
Max. transducer differential
pressure (in. w.g.)
Form 130.13-NOM1 (114) Supersedes:130.13-NOM1 (808)
Loading...