Johnson Controls TM-11x1 series Installation Instructions Manual

TM-11x1 Series Room Temperature Module

24- 10225- 4, Rev. C

Installation Instructions

Part No. 24-10225-4, Rev. C

Issued March 2016

Applications

The TM-11x1 Series of Room Temperature Modules
are designed for use with the TC-9102 Direct Digital
Control (DDC) terminal unit controller. The setpoin t dial
enables the room occupant to adjust the working
setpoint of the controller. On scaled models, the
marked adjustment range is 55 to 85°F; the controller
determines the actual setpoint. On Warmer/Cooler
models, the adjustment range is marked +/­midpoint of the dial; the controller determines the
equivalent setpoint temperature.

With the occupancy button, the occupant can switch
the controller’s operating mode between occupied and
standby. In addition, the TM-11x1 Series offers the
option of a temporary occupied mode during
unoccupied mode.

The TM-11x1 Series Room Temperature Module also
features a Light-Emitting Diode (LED) that indicates the
current operating mode.

from the

For TC-9102 Fan Coil Unit controllers, a Room
Temperature Module with a 3-speed fan override
adjustment is available, and models without a
temperature sensor are provided for applications
where the room temperature sensor is mounted inside
the Fan Coil Unit.

IMPORTANT: The TM-11x1 Series Room
Temperature Modules are intended to provide an
input to equipment under normal operating
conditions. Where failure or malfunction of the
TM-11x1 Temperature Module could lead to
personal injury or property damage to the controlled
equipment or other property, other precautions must
be designed into the control system. Incorpora te and
maintain other devices, such as supervisory or
alarm systems, or safety or limit controls intended to
warn of or protect against failure or malfunction of
the TM-11x1 Temperature Module.

Installation

Parts Included

Two #6-32 x 7/8 in. (22 mm) wallbox mounting screws
are included with the TM-11x1 Module.

Special Tools Needed

For tightening and loosening the TM-1 1x1 Series Room
Temperature Module security screw, order the optional
Allen-head tool (T-4000-119) fro m th e ne ar es t
Johnson Controls® representative.

TM-11x1 Series Room Temperature Module Installation Instructions 1

Dimensions

Figure 1: TM-1141 Dimensions, in. (mm)Figure 1: TM-1141 Dimensions, in. (mm)

3.15 (80)

4.72

F

I

G

:

T

M

4

1

_

d

i

m

Figure 2: TM-1151 Dimensions, in. (mm)

F

I

G

:

T

M

5

1

_

d

i

m

Mode

LED

Occupancy

Button

4.72

(120)

Figure 3: TM-1161 Dimensions, in. (mm)

F

I

G

:

T

M

6

1

_

d

i

m

4.72

(120)

Mode

LED

Button

Fan

Speed

Dial

Setpoint

Dial

Figure 4: TM-1191 Dimensions, in. (mm)

F

I

G

:

T

M

9

1

_

d

i

m

3.15 (80 )

1.38 (35)

4.72

(120)

Setpoint

Adjustment

Dial

TM-1141 Modules

TM-1161 Modules

TM-1151 Modules

1.26 (32)

(120)

1.38 (35)

3.15 (80)

Occupancy

Adjustment

TM-1191 Modules

1.26 (32)

3.15 (80)

TM-11x1 Series Room Temperature Module Installation Instructions2

Installing the TM-11x1

To install the TM-11x1 Series Room Temperature
Module:

1. Use the Allen-head tool to loosen the security
screw located at the top center of the housing.

2. Insert a screwdriver blade or coin into the slot on
the top of the housing.

3. Press down gently, and pry the housing away from
the base. As the two parts separate, remove the
blade or coin and continue to pull the housing away
from the base until the housing is free.

4. Pull the wires through the base. Locate the green
terminal blocks in the upper right of the base and
position the module on the wallbox with the
terminal numbers right-side up.

5. Mount the base to the wallbox using the two #6-32
mounting screws (included).

6. Wire the controller to the module. See the Wiring
section for correct wiring.

7. Attach the housing to the base and tighten the
security screw with the allen-head tool.

Mounting

Location Considerations

Mount the TM-11x1 Series Room Temperature Module
on a wall in the room to be controlled. Locate it where
the occupant can easily read and adjust the setpoint
dial or fan speed override adjustment dial. Consider
these additional guidelines to determine the best
mounting location:

• Avoid areas subject to excessive vibration,
electrical noise, direct sunlight, or the effects of
radiant heat.

• Keep electrical wiring as short as possible to
minimize temperature error.

• Install modules in areas where the temperature is
representative of the general room conditions.

Wiring

To wire a TC-9102 Controller to the TM-11x1 Series
Room Temperature Module, see the appropriate wiring
diagram (Figure 5 to Figure 9).

Note: Use 22 AWG (0.65 mm diameter) wire
minimum. Do not exceed 164 ft (50 m) between the
controller and the temperature module.

Table 1: Nominal Values for Sensors

Temperature Resistance
F Cohm

20 -7 10,595.0
30 -1 7,739.2
40 4 6,010.0
50 10 4,482.3
60 16 3,378.3
70 21 2,689.6
80 27 2,063.9
90 32 1,666.9
100 38 1,300.2
110 43 1,063.9
120 49 842.47
130 54 697.65

TM-11x1 Series Room Temperature Module Installation Instructions 3

TM-1141-0000

Figure 5: Wiring to an NTC Room Sensor

21

20

21

20

Common

Controller

Module

Figure 6: Wiring to a Room Temperature Module

Featuring an NTC Sensor with Occupancy

Override

F

I

15 15

14 14

21

20

21

20

Common

Mode LED

Controller

Module

Figure 7: Wiring to a Room Temperature Module

Featuring an NTC Sensor with Temperature

Setpoint Adjustment, and Occupancy Override

F

I

G

:

T

M

6

1

_

W

I

R

15

14

21

20

Common

Mode LED

23

22

15

14

21

20
23

22

Controller

Module

DC +5 V

Figure 8: Wiring to a Room Temperature Module

Featuring an NTC Sensor with Temperature

Setpoint Adjustment, Occupancy Override, and

Three-Speed Fan Override

F

I

G

:

T

M

6

1

_

W

I

R

2

15

14

21

20

NTC Sensor

Common

Mode LED

23

22

15

14

21

20
23

22

DC +5 V

Controller

Module

51 51 Thr ee-Speed Fan

Override

Figure 9: Wiring to a Room Temperature Module

Featuring an NTC Sensor with Temperature

Setpoint Adjustment without Occupancy

Override

F

I

G

:

T

M

9

1

_

W

I

R

20

21 Common

23

22

20

21

23

22

DC +5 V

Controller

Module

TM-1161-0002 and TM-1161-0007

Room Temperature

TM-1151-0000

Room Temperature

NTC Sensor

R

I
W

_

1
4

M
T

:
G

I
F

Occupancy Button

NTC Sensor

Room Temperature

Occupancy Button

Temperature Setpoint

TM-1191-0000 and TM-1191-0005

R

I
W

_

1
5

M
T

:
G

Room Temperature

NTC Sensor
Temperature Setpoint

TM-1161-0000 and TM-1161-0005

Room Temperature

Occupancy Button

NTC Sensor
Temperature Setpoint

TM-11x1 Series Room Temperature Module Installation Instructions4

The following messages apply to wiring this product.

!

!

!

CAUTION: Risk of Electric Shock.

Disconnect power supply before making
electrical connections to avoid electric
shock.

Mise En Garde: Risque de décharge
électrique. Débrancher l'alimentation

avant de réaliser tout raccordement
électrique afin d'éviter tout risque de
décharge électrique.

CAUTION: Risk of Property Damage.
Do not run low voltage cable in the same
conduit or wiring troughs with high
voltage wires. Running low and high
voltage wires in the same conduit or
wiring troughs may damage the
equipment or cause system malfunction.

MISE EN GARDE : Risque de dégâts
matériels.

Ne pas faire courir un câble basse
tension dans les mêmes gaines ou
goulottes électriques que des câbles
haute tension. L'installation de fils basse
tension et haute tension dans les mêmes
gaines ou goulottes électriques risque
d'endommager l'équipement ou de
provoquer des dysfonctionnements du
système.

CAUTION: Risk of Property Damage.
Do not apply power to the system before
checking all wiring connections. Short
circuited or improperly connected wires
may result in permanent damage to the
equipment.

Mise En Garde: Risque de dégâts
matériels. Ne pas mettre le système

sous tension avant d'avoir vérifié tous les
raccords de câblage. Des fils formant un
court-circuit ou connectés de façon
incorrecte risquent d'endommager
irrémédiablement l'équipement.

IMPORTANT: Use copper conductors only. Make
all wiring connections in accordance with local,
national, and regional regulations. Do not exceed
the Command Module electrical ratings.

Setup and Adjustments

Make temperature or fan speed adjustments to the
appropriate modules using the rotating dial, shown in
Figure 3 and Figure 4.

Repair Information

Do not field repair the TM-11x1 Series Room
Temperature Module. As with any electrical device,
keep the air vents clean and free from dust and
obstruction. To orde r re pla ce m en t parts, contact the
nearest Johnson Controls representative.

Technical Specifications

TM-11x1 Series Room Temperature Module (Part 1 of 2)

Models TM-1141-0000 Temperature Output Only

TM-1151-0000 Temperature Output with Occupancy Override
TM-1161-000x Temperature Output with Setpoint Adjustment and Occupancy

Override and Optional Fan Speed Adjustment

TM-1191-000x Temperature Output with Setpoint Adjustment
Power Requirements Powered from TC-9102 Controller.
Power Consumption N/A: Refer to individual component specification.
Inputs None
Adjustments Temperature Setpoint, Fan Speed (Optional by Model)
Mode Indicator Green LED (5 V, 4 mA)
Occupancy Button Momentary Contact (Switches 5 V at 1 mA)
Output Temperature Sensing

Element

Fan Speed 10k ohm Potentiometer, with Mechanically-Guided Positions

Resistance Temperature Device (RTD) Thermistor Negative
Temperature Coefficient (NTC) 2,252 ohm at 77°F (25°C)

at 0, 25, 50, 75, and 100% for Auto, Off, I (Low Speed),
II (Medium Speed), and III (High Speed)

TM-11x1 Series Room Temperature Module Installation Instructions 5

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.

All other marks herein are the marks of their respective owners. © 2016 Johnson Controls, Inc.

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

TM-11x1 Series

Setpoint Range TM-1141-0000

Room Temperature Module (Part 2 of 2)

No setpoint range

TM-1151-0000
TM-1161-0000

10k ohm potentiometer marked for 55 to 85°F

TM-1191-0000
TM-11x1-0002 10k ohm potentiometer marked for 55 to 85°F

Fan Speed Adjustment: Auto, Off, I, II, and III

TM-11x1-0005 10k ohm potentiometer marked for +/- (5F°)
TM-11x1-0007 10k ohm potentiometer marked for +/- (5F°)

Fan Speed Adjustment: Auto, Off, I, II, and III

Accuracy ±0.9°F (±0.5°C)
Field Connection 18 to 22 AWG (1.00 to 0.65 mm diameter) recommended
Mounting Wallbox Mount
Housing Material ABS + PC, Self-Extinguishing HB UL94
Protection IP30 (EN 60529)
Ambient Operating Conditions Temperature 32 to 122°F (0 to 50°C)

Humidity 10 to 90% RH (Noncondensing)

Ambient Storage Conditions Temperature -40 to 158°F (-40 to 70°C)

Humidity 5 to 95% RH (Noncondensing)

Dimensions
(H x W x D)

TM-1141
TM-1151

TM-1161
TM-1191

4.72 x 3.15 x 1.26 in.
(120 x 80 x 32 mm)

4.72 x 3.15 x 1.38 in.
(120 x 80 x 35 mm)

Shipping Weight 0.44 lb (0.2 kg)
Compliance Europe CE Mark: EMC Directive, EN-61000-6-2

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or

misuse of its products.

European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact:

JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY

JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA

JOHNSON CONTROLS
C/O CONTROLS PRODUCT
MANAGEMENT
NO. 22 BLOCK D NEW DISTRICT
WUXI JIANGSU PROVINCE 214142
CHINA

TM-11x1 Series Room Temperature Module Installation Instructions6

Published in U.S.A. www.johnsoncontrols.com