Johnson Controls TG9S040A08MP11, TG9S060A10MP11, TG9S060B12MP11, TG9S080B12MP11, TG9S080C16MP11 Quick Reference Manual

NOTES:

1. Refer to the condensate management and drain hose
plumbing for different configurations in this document. No
hose clamps are needed for the condensate pan hook up.

2. Drip leg in the gas line must be installed.

3. The furnace controls require correct polarity on the power
supply and a proper ground.

4. Y & G must be connected to the control board for cooling
operation.

5. To measure total static pressure add supply duct pressure to
the return duct pressure, add pressure drop across the ‘A’
coil, and add pressure drop across the filter. Ignore negative
signs on the readings.

6. Inlet gas pressure for natural gas should be 7” and that for
propane should be 11” w.c. Nominal manifold gas pressure
is 3.5” for natural gas and 10” w.c. for propane.

7. If thermoplastic evaporator ‘A’ coil drain pans are to be
installed in the up-flow/horizontal configuration, then extra 2”
minimum spacing may be needed to ensure against drain
pan distortion.

8. External filters required on all configurations.

9. Electrical entry is available on both sides of the casing.

10. All 33”, 95% furnaces are approved for single-pipe and 2­pipe systems. For single pipe systems it is recommended to
install the combustion air coupling provided and install
approximately 18” of PVC pipe on the furnace.

11. Do not install an external condensate trap on these fur­naces, as it will prevent the unit from operating correctly.

Models

Airflow CFM (Bottom Return without Filters)

Minimum Wire
Size awg @ 75'

One-Way

Total Unit

Amps

Maximum

Over Current

Protection

0.5" ESP (Nominal)

Low Med-Lo Med-Hi High

(T,G)G9S040A08MP11 581 653 818 950 14 8.0 15
(T,G)G9S060A10MP11

769 917 1038 1103 14 10.0 15

(T,G)G9S060B12MP11

713 872 1082 1243 14 10.0 15
(T,G)G9S080B12MP11 854 1008 1179 1370 14 10.0 15
(T,G)G9S080C16MP11

838 1250 1465 1671 14 11.5 15
(T,G)G9S080C22MP11

1285 1586 1937 2162 12 17.0 20
(T,G)G9S100C16MP11 819 1224 1477 1706 14 11.5 15
(T,G)G9S100C20MP11

1183 1430 1712 1934 12 17.0 20
(T,G)G9S120D16MP11

876 1254 1495 1805 14 11.5 15
(T,G)G9S120D20MP11 1190 1430 1739 1977 12 17.0 20
(T,G)G9S130D20MP11

1198 1459 1786 2047 12 17.0 20

Models

Maximum

Vent Equivalent

1

Factory Heating
Speed Setting

2

Temperature

Rise Range

Time For 1 ft

3

Natural Gas

(1030 Btu/Ft

3

)

Seconds On (Rate)

2" 3"

(T,G)G9S040A08MP11 65’ 90’ Med-Hi 30°F-60°F 93
(T,G)G9S060A10MP11 65’ 90’ High 30°F-60°F 62
(T,G)G9S060B12MP11 65’ 90’ Med-Hi 30°F-60°F 62
(T,G)G9S080B12MP11 65’ 90’ High 35°F-65°F 46
(T,G)G9S080C16MP11 65’ 90’ High 35°F-65°F 46
(T,G)G9S080C22MP11 65’ 90’ Med-Hi 35°F-65°F 46
(T,G)G9S100C16MP11 30’ 90’ High 35°F-65°F 37
(T,G)G9S100C20MP11 30’ 90’ Med-Hi 35°F-65°F 37
(T,G)G9S120D16MP11 30’ 90’ High 40°F-70°F 30
(T,G)G9S120D20MP11 30’ 90’ Med-Hi 35°F-65°F 30
(T,G)G9S130D20MP11 N/A 85’ High 45°F-75°F 28

1. For venting purposes, one 90° sweep elbow is equal to 5 Ft. of venting length, one 90° standard elbow is equal to 10 equiva-

lent feet of vent length. Vent termination elbows are included in these calculations, minimum required vent length is 5 ft.

2. Must be changed if not in rise range.

This document does not replace the installation instructions, which must be referred to for
detailed information.

CLEARANCES

* 24" clearance in front and 18" on side recommended for

service access.

All furnaces approved for alcove and attic installation.

DIMENSIONS

LED INDICATOR

Slow Green Flash

• Normal operation

Slow Amber Flash

• Normal operation with call for heat

Any Red Flash = Fault condition
Any Rapid 4 Flash = Potential fault codes / conditions

SUPPLY END

RETURN END

LEFT SIDE

Combustion Air Inlet

Condensate Drain
(Downflow)

Vent Connection
Outlet

Thermostat

Wiring

29.5”

28.5”

RIGHT SIDE

Condensate Drain
(Downflow)

14”

1”

1.5”

23”

Combustion Air Inlet

Gas Pipe

Entry

Electrical

Entry

Condensate

Drain

Optional Return Air
Cutout (Either side)

FRONT

A

33”

Clips can be flipped
into the up position
for coil cabinet or
plenum attachment

A-COIL

Follow all national, local codes and standards in addition to this document. The installation
must comply with regulations of the serving gas supplier, local building, heating, plumbing,
and other codes. In absence of local codes, the installation must comply with the national
codes andall authorities having jurisdiction.

B

24.25”

.56”

.56”

20”

3”

23.8”

.56”

Combustion
Air Inlet

2” Diameter
Vent Connection
Outlet

B

DURING INSTALLATION,
DOORS MUST REMAIN ON
FURNACE WHEN MOVING
OR LIFTING.

Vent Connection
Outlet

Application Upflow Downflow Horizontal

Top 1" 0" 0"
Vent 0" 0" 0"
Rear 0" 0" 0"
Side 0" 0" 1"

Front* 0" 0" 0"

Floor Combustible

Combustible

1

1. For combustible floors only when used with special
sub-base.

Combustible

Closet Yes Yes Yes

Line Contact No No Yes

Cabinet Size A (in) B (in)

All 'A' Cabinet Furnaces 14-1/2" 13-3/8"
All 'B' Cabinet Furnaces 17-1/2" 16-3/8"
All 'C' Cabinet Furnaces 21" 19-7/8"
All 'D' Cabinet Furnaces 24-1/2" 23-3/8"

QUICK REFERENCE GUIDE

95.5% SINGLE STAGE MULTI-POSITION

RESIDENTAL GAS FURNACES (33” TALL)

Subject to change without notice. Published in U.S.A. 401260-URG-E-0509
Copyright © 2009 by Johnson Controls, Inc. All rights reserved. Supersedes: 401260-URG-D-0808

Johnson Controls Unitary Products

5005 York Drive

Norman, OK 73069

*401260*

Furnace is multi-position and may be installed in any of the configurations shown.

Ensure that all PVC venting has at least 1/4” per foot slope towards the furnace.

The furnace condensate pan is self priming and contains an internal trap.

.Do not install an external condensate trap

When drain hose routing changes are required (shown in red), be sure to cap
all unused openings.
If rerouting hoses - excess length should be cut off so that no sagging loops will
collect and hold condensate, which will cause the furnace to not operate.

Move rain gutter hose
to this position

HORIZONTAL LEFT

Move pressure switch
hose to this position.
NOTE: May require the
longer hose that is
provided with wider cabinets

Change condensate drain
connection to the 90° fitting provided

Move condensate drain hose
to this position

Move rain gutter hose to this position
NOTE: May require hose extension that
is provided with wider cabinets

UPFLOW

DOWNFLOW

Move condensate drain
hose to this position

Move rain gutter
hose to this position

Inducer must be rotated
90° in either direction for
this installation

HORIZONTAL RIGHT

Move pressure switch
hose to this position

Change condensate drain
connection to the 90° fitting provided

Move rain gutter hose
to this position

Move condensate drain hose
to this position

Move rain gutter hose
to this position

Move pressure switch
hose to this position.
NOTE: May require the
longer hose that is
provided with wider
cabinets.

AIRFLOW

AIRFLOW

AIRFLOW

AIRFLOW

MOST COMMON INSTALLATION CONFIGURATIONS (MORE OPTIONS AVAILABLE WHICH IS COVERED IN THE INSTALLATION MANUAL)WITH INDUCER ROTATION,

Rain
Gutter
Hose

Pressure
Switch
Hose

Condensate
Drain Hose

For 100, 120 & 130K input furnaces, the condensate

drain is factory set toward the left casing outlet

For 040, 060 & 080K input furnaces, the condensate

drain is factory set toward the right casing outlet

MULTI-POSITION CONFIGURATION INFORMATION:

1

2

3

4

1

2

5

4

3

1

2

3

4

In upflow and downflow installation - Condensate drain hose may go out either side.

NOTE: Only side venting on 130K unit.