Johnson Controls TEC3000 Series Data Sheet

Code No. LIT-1900896

TEC3000 Series Thermostat Controller

Shown with Occupancy Sensor

Issued February 17, 2017

TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet® MS/TP or N2 Networked Thermostat Controllers Catalog Page

Description

The TEC3000 Series Thermostat Controllers are wireless, stand-alone, and field-selectable BACnet® Master-Slave/Token-Passing (MS/TP) or N2 networked devices that provide on/off, floating, and proportional control of the following:

• local hydronic reheat valves

• pressure-dependent VAV equipment with or without local reheat

• two- or four-pipe fan coils

• cabinet unit heaters

• other zoning equipment using an on/off, floating, or 0 to 10 prop

ortional control input

Models also provide single- or two-stage control of unitary rooftop units (RTUs) with or without economizers and heat pumps.

The field-selectable BACnet MS/TP or N2 networked thermostat controllers enable remote monitoring and programming through the building automation system, for efficient space temperature control. The wireless thermostat controllers feature a connection to the ZFR Pro wireless network. All models include a USB port configuration that reduces installation time by allowing simple backup and restore features from a USB drive, which enables rapid cloning of configuration between like units.

Some models have occupancy sensing capability built into the device. These thermostat controllers maximize up to 30% energy savings in high-energy usage commercial buildings, such as schools and hotels, during occupied times by using additional standby setpoints.

All models feature an intuitive UI with backlit display that makes setup and operation quick and easy. Multiple fan configurations are supported for fan coil equipment types:

• single-speed

• multi-speed (two or three discrete speeds)

• variable-speed/EC motors (0 to 10 VDC contro

Some models rehea

t, and four-pipe fan coil units with or without reheat. When heating is r and activates dehumidification control as necessary. Heat and/or

t is used as required to maintain the space temperature. For

rehea optimal dehumidification performance, use a fan coil unit multi-

speed or variable-speed fan (VSF). Models are available with or without the Johnson Controls® logo. Refer to the TEC3000 Series Wireless, Stand-Alone, and

Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controllers Product Bulletin (LIT-12011954) for important product

application information.

support dehumidification on two-pipe fan coil units

equired, the thermostat controller monitors

Features

• Two Configurable Binary Inputs—Provide additional inputs for

advanced functions such as remote night setback, service or filter alarms, motion detector, and window status.

• Wireless Communication Protocol ZFR Pro (TEC-30xx-0x-

Models)—

• Field-Selectable BACnet MS/TP or N2 Netw

Com

upgr networked communication without changing hardware.

• USB Port Configuration—Reduces

simple backup enables rapid cloning of configuration bet

• Backlit Liquid Crystal Display (LCD)—Offers real-time cont

atus of the environment in easy-to-read, plain text messages with

adjustable backlight that brightens during user interaction.

Reduces installation time and costs.

munication (TEC36xx-0x-000 Models)—Simplifies

ade from N2 networked communication to BACnet MS/TP

and restore features fr

installation time by allowing om a USB drive, which

orked

ween like units.

VDC

with

space humidity

that has a

000

the

rol

• Configurable Touchscreen UI—Allows facility managers to limit the user

interaction with the thermostat controller display based on

specific energy policies.

• End-of-Line Switch—Simplifies the layout and installation communication

• Mobile Access Portal (MAP) Gateway Compatib

• Stand-Alone and BACnet MS/TP or N2 Networked Models—

• Onboard Occupancy Sensor (TEC3xx1-0x-000 and

• On

• Integral Humidity Sensor (TEC3xx2-0x-000 a

• Multiple Fan Configurations for Fan Coil Equipment Types—

• Full Line of Remote TE-6300 Series Temperature Sensors—

• Built-In Schedule Object—Allows all wired models of

• Optimal Start—Allows each thermostat controller to anticipa

• Auto-Tuned Control Loops—Reduce commissioning

• Load Shed—Commands a load shed input to offset the heating and

Release 4.0 or Later)—Allows the user to view equipment

(MAP

and control conditions using mobile devices.

Offer application flexibility.

TEC3xx3-0x-000 Models)—Provides ener high-

energy usage commercial buildings without additi

installation time or cost.

/Off, Floating, Proportional 0 to 10 VDC, and Single-

o-Stage Control—Offers additional application flex

providing mor

TEC3xx3-

dehumidification control on two-pipe fan coil units with reh

pipe fan coil units with or without reheat.

four-

Provide field-selectable single-speed, multi-speed, var

iable-speed fan control capabilities.

Support a wide range of remote temperature sensing needs fr single supp

thermostat controllers to be scheduled as stand-alo allows BACnet the building automation system.

heatin

g or cooling needs of a space by starting the equipment early enough to reach the setpoint at the beginning of the occupancy.

elimina and tear of the mechanical devices.

cooling setpoints by a fixed amount on net chang

e rate of the setpoints is adjustable. The load shed feature in place to help satisfy defined in joint appendix JA5, section JA5.2.4 for deman response. The tr and passed

buses.

gy savings in

e advanced control signals.

0x-000 Models)—Monitors space humidity and activates

lier.

MS/TP models to be defined and adjusted through

te change-of-season recommissioning, and reduce wear

worked models. The

the California Title 24 requirements that are

igger for this event is defined in another contro

through the network command.

ility

onal

ibility by

eat and

and

om a

ne devices;

te the

scheduled

time,

d signal

ller

The performance specifications are nominal and conform to acceptable industry standards. For applications at conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls shall not be liable for damages resulting from misapplication or misuse of its products. © 2017 Johnson Controls.

TEC3000 Series Thermostat Controller Shown with Occupancy Sensor,

Dimensions, in. (mm)

FIG:t hermostat fe atures

USB Port

Display

Cover Screw

1-13/32

(36)

Occupancy

Sensor

4-23/32

(120)

5-5/8 (143)

TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet® MS/TP or N2 Networked Thermostat Controllers Catalog Page (Continued)

Selection Charts

Control Output Onboard

RTU/heat pump with economizer

Occupancy

Capability

Sensor

No No

Yes No

Dehumidification

Wireless Thermostat Controller Models

Code Number Johnson Controls

Logo

TEC3010-00-000 Yes On/off or floating fan coil and zoning No No TEC3010-01-000 No On/off or floating fan coil and zoning No No TEC3011-00-000 Yes On/off or floating fan coil and zoning Yes No TEC3011-01-000 No On/off or floating fan coil and zoning Yes No TEC3012-00-000 Yes On/off or floating fan coil and zoning No Y es TEC3012-01-000 No On/off or floating fan coil and zoning No Yes TEC3013-00-000 Yes On/off or floating fan coil and zoning Yes Yes TEC3013-01-000 No On/off or floating fan coil and zoning Yes Yes TEC3020-00-000 Yes 0 to 10 VDC proportional fan coil and zoning No No TEC3020-01-000 No 0 to 10 VDC proportional fan coil and zoning No No TEC3021-00-000 Yes 0 to 10 VDC proportional fan coil and zoning Y es No TEC3021-01-000 No 0 to 10 VDC proportional fan coil and zoning Yes No TEC3022-00-000 Yes 0 to 10 VDC proportional fan coil and zoning No Yes TEC3022-01-000 No 0 to 10 VDC proportional fan coil and zoning No Yes TEC3023-00-000 Yes 0 to 10 VDC proportional fan coil and zoning Y es Yes TEC3023-01-000 No 0 to 10 VDC proportional fan coil and zoning Yes Yes TEC3030-00-000 Yes Single- or two-stage

TEC3030-01-000 No Single- or two-stage

TEC3031-00-000 Yes Single- or two-stage

TEC3031-01-000 No Single- or two-stage

1. Multiple fan configurations are supported for fan coil equipment types.

TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet® MS/TP or N2 Networked Thermostat Controllers Catalog Page (Continued)

Stand-Alone Thermostat Controller Models

Code Number Johnson Controls

Logo

Control Output Onboard

Occupancy Sensor

TEC3310-00-000 Yes On/off or floating fan coil and zoning No No TEC3310-01-000 No On/off or floating fan coil and zoning No No TEC3311-00-000 Yes On/off or floating fan coil and zoning Yes No TEC3311-01-000 No On/off or floating fan coil and zonin g Yes No TEC3312-00-000 Yes On/off or floating fan coil and zoning No Yes TEC3312-01-000 No On/off or floating fan coil and zonin g No Yes TEC3313-00-000 Yes On/off or floating fan coil and zoning Yes Yes TEC3313-01-000 No On/off or floating fan coil and zoning Yes Yes TEC3320-00-000 Yes 0 to 10 VDC proportional fan coil and zoning No No TEC3320-01-000 No 0 to 10 VDC proportional fan coil and zoning No No TEC3321-00-000 Yes 0 to 10 VDC proportional fan coil and zoning Yes No TEC3321-01-000 No 0 to 10 VDC proportional fan coil and zoning Yes No TEC3322-00-000 Yes 0 to 10 VDC proportional fan coil and zoning No Yes TEC3322-01-000 No 0 to 10 VDC proportional fan coil and zoning No Yes TEC3323-00-000 Yes 0 to 10 VDC proportional fan coil and zoning Yes Yes TEC3323-01-000 No 0 to 10 VDC proportional fan coil and zoning Yes Yes TEC3330-00-000 Yes Single- or two-stage

TEC3330-01-000 No Single- or two-stage

TEC3331-00-000 Yes Single- or two-stage

TEC3331-01-000 No Single- or two-stage

1. Multiple fan configurations are supported for fan coil equipment types.

RTU/heat pump with economizer

No No

Yes No

Dehumidification Capability

Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controller Models1 (Part 1 of 2)

Code Number Johnson Controls

Logo

Control Output Onboard

Occupancy

Dehumidification Capability

Sensor

TEC3610-00-000 Yes On/off or floating fan coil and zoning No No TEC3610-01-000 No On/off or floating fan coil and zoning No No TEC3611-00-000 Yes On/off or floating fan coil and zoning Yes No TEC3611-01-000 No On/off or floating fan coil and zonin g Yes No TEC3612-00-000 Yes On/off or floating fan coil and zoning No Yes TEC3612-01-000 No On/off or floating fan coil and zonin g No Yes TEC3613-00-000 Yes On/off or floating fan coil and zoning Yes Yes TEC3613-01-000 No On/off or floating fan coil and zoning Yes Yes TEC3620-00-000 Yes 0 to 10 VDC proportional fan coil and zoning No No TEC3620-01-000 No 0 to 10 VDC proportional fan coil and zoning No No TEC3621-00-000 Yes 0 to 10 VDC proportional fan coil and zoning Yes No TEC3621-01-000 No 0 to 10 VDC proportional fan coil and zoning Yes No TEC3622-00-000 Yes 0 to 10 VDC proportional fan coil and zoning No Yes TEC3622-01-000 No 0 to 10 VDC proportional fan coil and zoning No Yes TEC3623-00-000 Yes 0 to 10 VDC proportional fan coil and zoning Yes Yes TEC3623-01-000 No 0 to 10 VDC proportional fan coil and zoning Yes Yes

TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet® MS/TP or N2 Networked Thermostat Controllers Catalog Page (Continued)

Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controller Models1 (Part 2 of 2)

Code Number Johnson Controls

Logo

TEC3630-00-000 Yes Single- or two-stage

TEC3630-01-000 No Single- or two-stage

TEC3631-00-000 Yes Single- or two-stage

TEC3631-01-000 No Single- or two-stage

1. Multiple fan configurations are supported for fan coil equipment types.

Accessories (Order Separately)

Product

Description

Code Number

TEC-WALLPLT Wallplate for retrofitting existing installations or concealing mounting surface damage; can be used with any TEC3000 Series

MS-WNC1820-0A WNC1800-0SZ with base, 120 to 230 VAC power, ZFR1820 ProCordFlag, with 3 ft (0.9 m) cable MS-WNC1823-0A WNC1800-0SZ with base, 120 to 230 VAC power, ZFR1823 ProCordWall, with 10 ft (3 m) cable MS-WNC1820-0B WNC1800-0SZ with base, 24 VAC power, ZFR1820 ProCordFlag, with 3 ft (0.9 m) cable MS-WNC1823-0B WNC1800-0SZ with base, 24 VAC power, ZFR1823 ProCordWall, with 10 ft (3 m) cable MS-ZFR1821-0B ZFR1821 Pro Flag Repeater, 24 V AC/DC power, with 3 ft (0.9 m) cable MS-ZFR1822-0B ZFR1822 Pro Wall Mount Repeater, 24 VAC/DC power , with 10 ft (3 m) cable MS-ZFR1821-0 ZFR1821 Pro Flag Router, with 3 ft (0.9 m) cable MS-ZFR1822-0 ZFR1822 Pro Wall Mount Router, with 10 ft (3 m) cable ZFR-CBLEXT-0 10 ft (3 m) extension cable accessory, RJ12 F-F coupler ZFR-WALLCOVER ZFR Repeater wallplate cover ZFR-USBHA-0 Wireless USB dongle

TE-6300 Series T-4000-119 Allen-head adjustment tool (30 per bag)

1. See Johnson Controls TE-6300 Series T emperature Sensors table for ordering details regarding Johnson Controls TE-6300 Series Remote Temperature Sensors.

Thermostat Controller

Remote temperature sensors

Control Output Onboard

Occupancy Sensor

RTU/heat pump with economizer

No No

Yes No

Dehumidification Capability

TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet® MS/TP or N2 Networked Thermostat Controllers Catalog Page (Continued)

Johnson Controls TE-6300 Series Temperature Sensors (Order Separately) (Part 1 of 2)

Sensor Type Mounting Style Probe Length Product

Nickel (1k ohm)

Platinum (1k ohm)

Platinum Equivalent

Thermistor (2.2k ohm)

Adjustable Averaging 8 ft (2.4 m) TE-6315M-1

Duct 4 in. (102 mm) TE-631GM-1

Flange 4 in. (102 mm) TE-631GV-2

Flush N/A TE-6310F-0

Outside air 3 in. (76 mm) TE-6313P-1 Strap-mount 3 in. (76 mm) TE-631S-1 Wall Well 6 in. (152 mm) TE-631AM-2

Adjustable 8 in. (203 mm) TE-6351-A Duct 4 in. (102 mm) TE-635GM-1

Flange 4 in. (102 mm) TE-635GV-2

Flush N/A TE-6350F-0

Strap-mount 3 in. (76 mm) TE-635S-1 Outside air 3 in. (76 mm) TE-6353P-1 Wall Well 6 in. (152 mm) TE-635AM-2

1k ohm averaging

100 ohm averaging

Adjustable 8 in. (203 mm) TE-6341A-1 Duct 8 in. (203 mm) TE-6341P-1 Flange 4 in. (102 mm) TE-634GV-2

Outside air 3 in. (76 mm) TE-6343P-1 Wall Well 8 in. (203 mm) TE-6342M-1

8 in. (203 mm) TE-6311A-1

17 ft (5.2 m) TE-6316M-1

8 in. (203 mm) TE-6311M-1

18 in. (457 mm) TE -631JM-1

8 in. (203 mm) TE-6311V-2

N/A TE-6314P-1

8 in. (203 mm) TE-6312M-1

8 in. (203 mm) TE-6351M-1

18 in. (457 mm) TE -635JM-1

8 in. (203 mm) TE-6351V-2

N/A TE-6324P-1

8 in. (203 mm) TE-6352M-1 10 ft (3 m) TE-6327P-1 20 ft (6.1 m) TE-6328P-1 10 ft (3 m) TE-6337P-1 20 ft (6.1 m) TE-6338P-1

8 in. (203 mm) TE-6341V-2

N/A TE-6344P-1

6 in. (152 mm) TE-634AM-2

Code Number

TE-6315V-2

TE-6316V-2

TE-6311P-1

TE-6310F-1

TE-6351P-1

TE-6350F-1

TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet® MS/TP or N2 Networked Thermostat Controllers Catalog Page (Continued)

Johnson Controls TE-6300 Series Temperature Sensors (Order Separately) (Part 2 of 2)

Sensor Type Mounting Style Probe Length Product

Thermistor (10k ohm) Type II

1. Two TE-6001-8 Element Holders come with the plat inum-equivalent averaging sensors. Order separately to use with a nickel averaging sensor.

2. Order the TE-1800-9600 Mounting Hardware separately to mount the wall unit to a wallbox.

Adjustable 8 in. (203 mm) TE-6361A-1 Duct 4 in. (102 mm) TE-636GM-1

8 in. (203 mm) TE-6361M-1

18 in. (457 mm) TE-636JM-1

Flange 4 in. (102 mm) TE-636GV-2

8 in. (203 mm) TE-6361V-2

Flush N/A TE-6360F-0

Outside air 3 in. (76 mm) TE-6363P-1 Strap-mount 3 in. (76 mm) TE-636S-1 Well 6 in. (152 mm) TE-636AM-2

8 in. (203 mm) TE-6362M-1

Repair Information

If the TEC3000 Series Thermostat Controller fails to operate within its specifications, replace the unit. For a replacement thermostat controller, contact the nearest Johnson Controls representative.

Code Number

TE-6361P-1

TE-6360F-1

Technical Specifications

TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controllers (Part 1 of 2)

Power Requirements 19 to 30 VAC, 50/60 Hz, 4 VA at 24 VAC nominal, Class 2 or safetyextra-low voltage (SELV) Analog Output Rating

(Proportional Control Models) Relay Contact Rating

(On/Off, Floating, or Staged Economizer Control Models)

Fan Relay Output Rating (On/Off, Floating, and Proportional Control Models)

Auxiliary Output Rating/Triac Output (On/Off, Floating, and Proportional Control Models)

Binary Inputs Dry contact across terminal COM to terminals BI1, BI2, or COS Analog Inputs Nickel, platinum, A99B, 2.25k ohm negative temperature coefficient (NTC), 10k ohm NTC, 10k ohm NTC Type 3

Temperature Sensor Type Local 1k ohm platinum sensor Wire Size 18 AWG (1.0 mm diameter) maximum, 22 AWG (0.6 mm diameter) recommended MS/TP Network Guidelines Up to 100 devices maximum per Network Automation Engine (NAE);

Wireless Band Direct-sequence, spread-spectrum, 2.4 GHz ISM band Transmission Power 10 mW maximum Transmission Range 50 ft (15.2 m) practical average indoor

Temperature Range

Accuracy Temperature ±0.9F°/±0.5C° at 70.0°F/21.0°C typical calibrated

Minimum Deadband 2F°/1C° between heating and cooling

Backlit Display -40.0°F/-40.0°C to 122.0°F/50.0°C in 0.5° increments Heating Control 40.0°F/4.5°C to 90.0°F/32.0°C Cooling Control 54.0°F/12.0°C to 100.0°F/38.0°C

Humidity (On/Off, Floating, and Proportional Control Models)

0 to 10 VDC into 2k ohm resistance (minimum)

19 to 30 VAC, 1.0 A maximum, 15 mA minimum, 3. 0 A in-rush, Class 2 or SELV

19 to 30 VAC, 1.0 A maximum, 15 mA minimum, 3.0 A in-rush

across terminal COM to terminals R SEN or COS

4,000 ft (1,219 m) maximum cable length (repeaters can be added to extend this length)

250 ft (76.2 m) maximum indoor line of sight

±5% RH from 20 to 80% RH at 50 to 90°F (10 to 32°C)

TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet® MS/TP or N2 Networked Thermostat Controllers Catalog Page (Continued)

TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controllers (Part 2 of 2)

Occupancy Sensor Motion Detection (Occupancy Sensing Models)

Ambient Conditions

Compliance BACnet

Shipping Weight

Operating 32 to 122°F (0 to 50°C); 95% RH maximum, noncondensing Storage -22 to 122°F (-30 to 50°C); 95% RH maximum, noncondensing

International United States UL Listed, File E27734, CCN XAPX, under UL60730

Canada UL Listed, File E27734, CCN XAPX7 under E60730

Europe CE Mark—Johnson Controls declares that this product is in compliance with the essential req uirements and other

Australia and New Zealand

Models without Occupancy Sensor

Models with Occupancy Sensor

Minimum of 94 angular degrees up to a distance of 15 ft (4.6 m); based on a clear line of sight

BACnet Testing Laboratories™ (BTL) 135-2001 Listed BACnet Application Specific Controller (B-ASC)

Transmission complies with FCC Part 15.247 regulations for low power unlicensed transmitte rs; transmitter identification FCC: OEJ-WRZRADIO

Industry Canada (IC) RSS-210; transmitter identification ZFR1810-1: IC: 279A-WRZRADIO

relevant provisions of the Radio Equipment Directive (RED), the Low Voltage Directive (LVD), the EMC Directive, and the RoHS Directive.

RCM Mark, Australia/NZ Emissions Compliant

0.75 lb (0.34 kg)

0.77 lb (0.35 kg)

Johnson Controls TEC3000 Series Data Sheet

Specifications and Main Features

Frequently Asked Questions

User Manual

Description

Features

Selection Charts

Repair Information

Technical Specifications