Johnson Controls TE-6300F Series, TE-6310F-0, TE-6310F-1, TE-6350F-1, TE-6350F-0 Installation Instructions Manual

Figure 1: Flush Mount Sensor with Logo

Dimensions, in. (mm)

4 -1/2
(114.3)

2 -3/4
(69.85)

F

i

g

:

D

i

m

TE-6300F Series Flush Mount Sensors

24- 4034-255, Rev. C

Installation Instructions

TE-63xxF-0, TE-63xxF-1

Refer to the QuickLIT website for the most up-to-date version of this document.

Part No. 24-4034-255, Rev. C

Issued March 2016

Applications

The TE-6300F Series Flush Mount Te mperature
Sensor is a device that measures air temperatur e, via a
temperature sensing element, thermally bonded to a
metal electrical box cover. The sensor is designed for
direct connection to a supervisory controller.

IMPORTANT: The TE-6300F Series Flush Mount
Temperature Sensor is intended to provide an input
to equipment under normal operating conditions.
Where failure or malfunction of the sensor could
lead to personal injury or property damage to the
controlled equipment or other property, additional
precautions must be designed into the control
system. Incorporate and maintain other devices,
such as supervisory or alarm systems or safety or
limit controls, intended to warn of or protect against
failure or malfunction of the sensor.

IMPORTANT : Le TE-6300F Series Flush Mount
Temperature Sensor est destiné à transmettre des
données entrantes à un équipement dans des
conditions normales de fonctionnement. Lorsqu'une
défaillance ou un dysfonctionnement du sensor
risque de provoquer des blessures ou
d'endommager l'équipement contrôlé ou un autre
équipement, la conception du système de con tr ôle
doit intégrer des dispositifs de protection
supplémentaires. Veiller dans ce cas à intégrer de
façon permanente d'autres dispositifs, tels que des
systèmes de supervision ou d'alarme, ou des
dispositifs de sécurité ou de limitation, ayant une
fonction d'avertissement ou de protection en cas de
défaillance ou de dysfonctionnement du sensor.

Installation

IMPORTANT: Do not install the TE-6300F Series

Flush Mount Temperatur e Sensor probe in ambient
temperatures beyond the specified 32 to 104°F
(0 to 40°C) temperature range. Installing the
temperature sensor probe in ambient temperatures
beyond this range may damage the unit and void the
warranty.

Dimensions

TE-6300F Series Flush Mount Sensors Installation Instructions 1

Mounting

Figure 2: Installing a Sensor Plate to the

Conduit Box

!

Location Considerations

Consider the following mounting location guidelines:

• Avoid areas subject to excessive vibration,
electrical noise, direct sunlight, or the effects of
radiant heat.

• Keep electrical wiring as short as possible to
minimize temperature error.

Mounting the Temperature Sensor

Mount the temperature sensor as follows:

1. Remove the appropriate knockout on the standard
utility conduit box for the application.

2. Make the wiring connection to the system
components.

Note: To make wiring easier, the sensor may be
suspended from the conduit box using the rubber band.

Note: Level the sensor for appearance; however, the
sensor functions normally when not level.

3. Mount the sensor to the wallbox or electrical box
using the screws provided.

Wiring

For 1k ohm nickel temperature sensors, wire
resistance can cause approximately 1F° (0.56C°) of
error for every 250 ft (76 m) run of 18 AWG wire, or
every 100 ft (31 m) run of 22 AWG wire. For 1k ohm
platinum temperature sensors, wire resistance can
cause approximately 1F° (0.56C°) of error for every
150 ft (46 m) run of 18 AWG wire, or every 50 ft (15 m)
run of 22 AWG wire. To minimize error due to field
wiring, limit the total resistance of all nickel temperature
sensor wiring to 3 ohms, and all 1k ohm platinum
temperature sensor wiring to 2 ohms.

The 10k ohm thermistor applications tolerate relatively
long wiring before the wire resistance adds significantly
to the total resistance measured at the controller. As a
general rule, a 150 ft (46 m) two-wire 18 AWG run
contributes 2 ohms of error, or less than 1F° (0.56C°)
error over the sensor operating temperature range.

Refer to the appropriate controller documentation for
recommended sensor wiring.

CAUTION: Risk of Property Damage.

Do not apply power to the system before
checking all wiring connections. Short
circuited or improperly connected wires
may result in permanent damage to the
equipment.

MISE EN GARDE : Risque de dégâts
matériels.

Ne pas mettre le système sous tension
avant d'avoir vérifié tous les raccords de
câblage. Des fils formant un court-circuit
ou connectés de façon incorrecte
risquent d'endommager
irrémédiablement l'équipement.

IMPORTANT: Use copper conductors only. Make
all wiring connections in accordance with local,
national, and regional regulations. Do not exceed
the TE-6300F Series Flush Mount Temperature
Sensor’s electrical ratings.

Wiring Recommendations

IMPORTANT: Use proper Electrostatic Discharge
(ESD) precautions during installation and operation
to avoid damaging the electronic circuits. Use
electrical tape to wrap the ends of the wire leads a
minimum of 1 in. (25 mm), as well as to cover the
wire nuts.

Use the wire nuts provided for connecting the lead
wires to the controller wiring.

TE-6300F Series Flush Mount Sensors Installation Instructions2