The TE-6300 Temperature Sensor line
provides economical solutions for a wide
variety of temperature sensing needs,
including wall-mount, outdoor-air, duct,
strap-mount, well-insertion, duct-averaging,
and Variable Air Volume (VAV) flange-mount
duct-probeapplications. The TE-6300 line
offers both a metal and a plastic enclosure for
the most popular models.
Sensors are available in the following types:
• 1k ohm thin-film nickel
• 1k ohm nickel averaging
• 1k ohm thin-film platinum
• 100 ohm platinum equivalent averaging
• 1k ohm platinum equivalent averaging
• 2.2k (2,252) ohm thermistor
• 10k ohm thermistor, Johnson Controls®
Type II
Each sensor is packaged with the necessary
mounting accessories to maximize ordering
and installation ease and reduce both
commissioning time and cost.
Refer to the TE-6300 Temperature Sensors Product Bulletin (LIT-216320) for important
product application information.
Features
• full line of versatile sensors — supports all
your temperature sensing needs from a
single supplier: wall mount, outdoor air,
duct probe, duct averaging, strap-mount,
well insertion, and flange mount duct probe
• single assembly ordering — simplifies
ordering; provides a complete assembly in
one box
• models featuring an integral NPT Adaptor
— increase sensor connection strength,
which eliminates the need for a special
adaptor
• models with a stainless steel sensor probe
— protect the sensor while increasing
corrosion resistance
• metal enclosure (TE-63xxM Models only)
— meets plenum requirements
• models featuring a retainer for the sensor
holder — allow you to lock the sensor
holder into the conduit box
• include two hex-head self-drilling screws
for mounting
• come equipped with a 10 ft (3 m)
plenum-rated cable with 1/4 in. (6.35 mm)
female insulated quick-connect
terminations on leads
TE-63xxF Models
The TE-63xxF (flush mount) models:
• provide a low profile when installed in an
electrical box
• feature thermally isolated sensor from the
wall with a foam pad
• offer a rugged stainless steel cover
• provide 22 AWG lead wires with low
voltage installation
TE-63xxM Models
The TE-63xxM (metal enclosure) models:
• come with a corrosion-protected steel
enclosure with a 0.88 in. (22 mm) hole for a
1/2 in. (12.7 mm) conduit fitting
• include two hex-head self-drilling screws
for mounting the duct and duct averaging
models
• offer (well models only) either a direct
mount or 1/2-14 NPT threaded well sensor
holder for mounting in TE-6300W Series
thermal wells (Order the thermal well
separately.)
• provide optional well sensor holders (order
separately) to mount duct models in
thermal wells.
• meet UL 1995 plenum use requirements
• offer optional accessory kit (order
separately) to replace plastic hole plug and
wiring bushing to meet International
Mechanical Code (IMC) requirements
TE-63xxP Models
The TE-63xxP (plastic enclosure) models:
• provide a thermoplastic conduit box with
1/2-14 NPT female thread for connecting to
conduit
• provide aluminum mounting plate and
1/2-14 NPT threaded hub mounting options
for the duct and duct averaging models
• use the 1/2-14 NPT female thread to mount
the Outdoor Air models directly to ridged
conduit
• provide optional sensor holders (order
separately) to mount duct models in
thermal wells
• offer an optional accessory metal cover kit
(order separately) to replace the plastic
cover to meet UL 1995 plenum use
requirements
• include a replaceable sensing probe on
duct probe, outdoor air, and well insertion
models
TE-63x4P Wall Mount Models
The TE-63x4P (plastic enclosure) models:
• come with a white thermoplastic ventilated
cover with a brushed aluminum face plate
and a steel mounting plate for surface
mounting
• include faceplates for both horizontal and
vertical mounting
• offer an accessory mounting kit for
mounting to a standard electrical box
• offer optional covers
TE-63xS Models
The TE-63xS (Strap-Mount) models:
• provide a 1/4 in. (6.35 mm) diameter
stainless steel probe without an enclosure
• include three cable ties for mounting to
pipe up to 2-5/8 in. (67 mm) diameter
• come equipped with a 10 ft (3 m) plenum
rated cable
• meet UL 1995 plenum use requirements
• offer an accessory mounting kit for
mounting to a pipe up to 11 in. (280 mm)
diameter
TE-63xxV Models
The TE-63xxV (VAV flange mount) models:
• provide a stainless steel mounting flange
with two hex-head self-drilling mounting
screws
• come equipped with a 10 ft (3 m) plenum
rated cable with 1/4 in. (6.35 mm) female
insulated quick-connect terminations on
leads
• meet UL 1995 plenum use requirements
Repair Information
If the TE-6300 Series Temperature Sensor
fails to operate within its specifications, refer
to the TE-6300 Series Temperature Sensors Product Bulletin (LIT-216320) for a list of
repair parts available.
F-1000-182Thermal Conductive Grease for element wells (8 oz.)
T-4000-119Allen Head Tool for Wall Mount Cover Screws (order in multiples of 30)
TE-1800-9600Mounting Hardware for mounting the wall mount unit to a wall box
TE-6001-8Element Holder for mounting an averaging sensor (order in multiples of 10)
TE-6001-13Metal Cover and Gasket Kit (5 per package)
TE-6300-10112 in. (305 mm) (1k ohm) Nickel Probe (cut to an appropriate length)
TE-6300-1031/2-14 NPT Plastic Sensor Holder without retainer (order in multiples of10)
TE-6300-10512 in. (305 mm) (1k ohm) Platinum Class A Probe (cut to an appropriate length)
TE-6300-6018 in. (203 mm), 1k ohm Nickel Probe
TE-6300-6033 in. (76 mm), 1k ohm Nickel Probe
TE-6300 Temperature Sensor Models (Part 2 of 2)
SensorMounting Style Probe Length
Platinum
Equivalent
Thermistor
(2.2k ohm)
Thermistor
(10k ohm)
Type II
1. Two TE-6001-8 Element Holders come with the platinum equivalent
averaging sensors. Order separately to use with a nickel averaging sensor .
2. Order the TE-1800-9600 Mounting Hardware separately to mou nt the wall
unit to a wallbox.
3. TE-631AM-1, TE-635AM-1, and TE-636AM-1 include TE-6300-612 brass
threadless well adaptor for retrofit to TE-6300W-103 or WZ-1000-5
thermowells.
TE-6300-605Sensor Holder/Well Adaptor, Plastic, 1/2-14 NPT, for use with TE-6300W-1 10 (replacement part, included with
TE-6300-6068 in. (203 mm), 2.2k ohm Thermistor Probe
TE-6300-6073 in. (76 mm), 2.2k ohm Thermistor Probe
TE-6300-608NCT Thermistor Sensor with 8 ft (2.4 m) Leads
TE-6300-609Sensor Holder/Well Adaptor, Plastic, Threadless, for use with TE-6300W-103 (replacement part, included with
TE-6300-610NCT Thermistor Sensor with 12 ft (3.7 m) Leads
TE-6300-6111/2-14 NPT Threaded Brass Sensor Holder (Order in multiples of 10)
TE-6300-612Threadless Brass Sensor Holder (Order in multiples of 10)
TE-6300-613IMC Kit, Metal Knockout Plug, Metal Clamp Connector (or der in multiples of 10)
TE-6300-614Cable Tie Mounting Kit, 0.50 to 2.625 in. (12.7 to 66.7 mm) Bundle Diameter (10 per package)
TE-6300-615Cable Tie Mounting Kit, 11 in. (280 mm) Maximum Bundle Diameter
TE-6300-6168 in. (203 mm) 1k ohm Platinum Class A Probe
TE-6300-6173 in. (76 mm) 1k ohm Platinum Class A Probe
TQ-6000-14 to 20 mA Output Transmitter for use with the 100 ohm platinum sensor
TE-6300W-1016 in. (152 mm) Brass Well (direct mount with thermal grease included)
TE-6300W-1026 in. (152 mm) Stainless Steel Well (direct mount)
TE-6300W-1036 in. (152 mm) Brass Well, 1/2 in. – 14 NPT outside pipe thread (with thermal grease, r equires sensor with adapter)
TE-6300W-1108 in. (203 mm) Stainless Steel Well
1. Cut 12 in. probes to a minimum of 3 in. (76 mm).
TE-63xxP-1)
TE-63xAP-1)
T-4000 Covers Available for the Wall Mount TE-63x4P Series
Sensor Accuracy 1k ohm Nickel±0.34F° at 70°F (±0.19C° at 21°C)
1k ohm Nickel1k ohms at 70F (21C)
1k ohm Nickel Averaging
1k ohm Platinum1k ohms at 32°F (0°C)
100 ohm Platinum Averaging100 ohms at 32°F (0°C)
1k ohm Platinum Averaging1k ohms at 32F (0C)
2.2k ohm Thermistor2,252 ohms at 77F (25C)
10k ohm Thermistor10.0k ohms at 77F (25C)
1k ohm Nickel Averaging±3.4F° at 70°F (±1.9C° at 21°C)
1k ohm Platinum Class AEN 60751 Class A, ± [0.15 + 0.002 * | T °C |], ±0.19C° at 21°C (±0.35F° at 70°F)
100 ohm Platinum Class AEN 60751 Class A, ± [0.15 + 0.002 * | T °C |], ±0.19C° at 21°C (±0.35F° at 70°F)
1k ohm Platinum Class BEN 60751 Class B, ± [0.30 + 0.005 * | T °C |], ±0.41C° at 21°C (±0.73F° at 70°F)
100 ohm Platinum Averaging±1.0F°at 70°F (± 0.58C° at 21°C)
1k ohm Platinum Averaging
2.2k ohm Thermistor0.36F (0.2C) in the range: 32 to 158F (0 to 70C)
10k ohm Thermistor0.9F (0.5C) in the range: 32 to 158F (0 to 70C)
2.2k ohm ThermistorNonlinear, Negative Temperature Coefficient (NTC)
10k ohm ThermistorNonlinear NTC, Johnson Controls Type II
TE-63xxM22 AWG (0.6 mm diameter) x 6 in. (152 mm) long
TE-63xxP
TE-63xxF22 AWG (0.6 mm diameter) x 12 ft (3 m) braided-copper wires, low voltage insulation, half-
TE-63xxP Nickel Averaging18 AWG (1.0 mm diameter) x 6 in. (152 mm) long
TE-63xS22 AWG (0.6 mm diameter) x 10 ft (3 m) long plenum-r ated cable
TE-63xxA, TE-63xxV22 AWG (0.6 mm diameter) x 10 ft (3 m) long plenum-rated cable with 0.25 in. (6.35 mm) female
TE-63xxPConduit box and Shield: Rigid Thermoplastic
TE-63xxVMounting Flange: Stainless Steel
TE-63xxA-50 to 140°F (-46 to 60°C)
TE-63xxF32 to 104°F (0 to 40°C)
TE-63xxM-50 to 220°F (-46 to 104°C)
TE-63xxPEnclosure: -50 to 122°F (-46 to 50°C)
TE-63xSSensor Probe: -50 to 220°F (-46 to 104°C)
TE-63xxV
TE-63xxF0.25 lb (113.4 kg)
TE-63xxMDuct Averaging: 0.9 lb (0.41 kg)
TE-63xxPDuct Averaging: 0.5 lb (0.23 kg)
TE-63xSStrap-Mount: 0.2 lb (0.09 kg)
TE-63xxVDuct Averaging: 0.7 lb (0.32 kg)
stripped ends
quick-connect terminals
Nickel Averaging Adaptor: 0.25 in. (6.35 mm) O.D. Brass
Platinum Averaging Probe: 0.19 in. (4.8 mm) Aluminum tubing
All others (except Averaging): 0.25 in. (6.35 mm) O.D. Stainless Steel
Well Sensor Holder: 0.875 in. (22.2 mm) Hex Brass
Mounting Plate: Aluminum
Sensor Holder: Rigid Thermoplastic
Wall Mount Base Plate: Corrosion-Protected Steel
Wall Mount Cover: Rigid Thermoplastic (White)
Wall Mount Face Plate: Brushed Aluminum
Sensor Probe: -50 to 220°F (-46 to 104°C)
Wire Harness: -50 to 122°F (-46 to 50°C)
Duct Mount: 0.4 lb (0.18 kg)
Well Insertion: 0.5 lb (0.23 kg)
Duct Mount: 0.4 lb (0.18 kg)
Outdoor Air: 0.5 lb (0.23 kg)
Wall Mount: 0.2 lb (0.09 kg)
Well Insertion: 0.35 lb (0.16 kg)
TE-63xxA2.17 in. (55 mm) diameter plus 4 or 8 in. (102 or 203 m) element
TE-63xxFFlush Mount: 4-1/2 x 2-3/4 in. (114 x 70 mm)
TE-63xxMDuct Averaging: 1.87 x 1.87 x 1.80 in. (47.5 x 47.5 x 45.8 mm) plus 8 or 17 ft (2.4 or 5.2 m)
TE-63xxPDuct Averaging: 5.97 x 1.38 x 2.75 in. (152 x 35 x 70 mm) plus 8, 10, 17, or 20 ft
TE-63xSStrap-Mount: 0.25 in. (6.35 mm) diameter x 3.00 in. (76 mm.) long
TE-63xxVDuct Averaging: 2.25 x 1.50 in. (57 x 38 mm) plus 8 or 17 ft (2.4 or 5.2 m) element
element
Duct Mount: 1.87 x 1.87 x 1.80 in. (47.5 x 47.5 x 45.8 mm) plus 4, 8, or 18 in.
(102, 203, or 457 mm) element
Well Insertion: 1.87 x 1.87 x 1.80 in. (47.5 x 47.5 x 45.8 mm) plus 6 or 8 in. (152 or 203 mm)
element
(2.4, 3.0, 5.2, or 6.1 m) element
Duct Mount: 5.97 x 1.38 x 2.75 in. (152 x 35 x 70 mm) plus 6 or 8 in. (152 or 203 mm) probe
Outdoor Air: 5.97 x 3.47 x 4.46 in. (152 x 88 x 113 mm)
Wall Mount: 2.09 x 3.12 x 1.80 in. (53 x 79 x 46 mm)
Well Insertion: 5.97 x 1.38 x 2.75 in. (152 x 35 x 70 mm) plus 6 or 8 in. (152 or 203 mm) probe
Duct Mount: 2.25 x 1.50 in. (57 x 38 mm) plus 4 or 8 in. (102 or 203 m) element