Johnson Controls RIBMNLB, RIBLB Data Sheet

RELAYS
FAN SAFETY ALARM CIRCUITS
RIBMNLB
2.75˝ Track Mount AHU Fan Safety Alarm Circuit,
24 Vac Power Input
4A
Max.
1 2
24 Vac/dc
For Indoor Use
in Dry Locations
2mA @ 24
Vac/dc 2mA @ 24Vac/dc 2mA @ 24Vac/dc 2mA @ 24Vac/dc 3A @ 24Vac /dc 750mA @ 24Vac/dc
Power
On
Latched
Input
Selector
DIP
Switch
Latch Reset
J1 Jumper
3 4
Low Limit
1 5
Low Limit On
Low Limit
Relay
Low Limit
Digital In
10 11
8A @ 24
Static Pressure
Vac/dc
Detector/FA
Limit
Static Pressure On
Static
Pressure
Relay
Static Pressure
Digital In
12 13
8A @ 24Vac/dc 8A @ 24Vac/dc
Dry Contact Outputs (To Controller)
RIBLB
Enclosed AHU Fan Safety Alarm Circuit,
24 Vac Power Input
1 7
Fan Status
On
1 6
Detector/FA
SPECIFICATIONS
Expected Relay Life:
Operating Temperature:
Humidity Range:
Operate Time:
Power Input:
Alarm Status:
Dimensions:
Track Mount:
Approvals:
Housing Rating:
Gold Flash:
Override Switch:
Notes:
RIBMNLB and RIBLB have four Alarm Inputs and one
Master Alarm.
A master relay will open if any one of the normally-closed (N/C) inputs open. LED status of all outputs and the master relay is provided. The RIBMNLB is provided with mounting track for mounting in user-provided electrical enclosures. The RIBLB is enclosed in a NEMA 1, 4˝ x 7˝ enclosure with a clear lid to allow viewing of the status LEDs. The master relay has two general-purpose outputs: one 24 V output terminal and one dry contact output rated up to 10 Amp @ 277 Vac. Fan status contact controls actuator power. The most common applica­tion is an Air Handling Unit (AHU) fan-safety-shutdown where the master relay is used to shutdown the fan. Contact closure outputs are provided so that a DDC controller can determine the cause of a shutdown.
Model RIBMNLB combines all the relay logic to facilitate fan status, fan safety control, and damper actuator control. It is intended for use in a circuit that will control fan start/stop and fan safety shut-down circuit monitors three critical inputs:
• Low-limit freeze protection (to stop fan and remove power from damper actuator)
• Static pressure (to monitor for hi/low pressure condition)
• Smoke detector / re alarm
Master relay opens to shut down AHU when any Normally Closed input opens.
Integral DIP switch allows any input to be latched. Input can be reset with push button or by cycling unit power.
Installing J1 jumper allows Fan Status input to control Master Relay, like the other 3 inputs.
10 million cycles minimum mechanical
-30 to 140° F 5 to 95% (noncondensing) 250ms 4 Amp @ 24 Vac/dc ; 50-60 Hz LED On = Activated
6.000˝ x 2.750˝ x 1.200˝ (RIBMNLB)
4.28˝ x 7.00˝ x 2.00˝ with .75˝ NPT Nipple (RIBLB) MT212-6 Mounting Track Provided UL Listed, UL864, C-UL UL Listed, NEMA 1, C-UL, CE Approved No No
Fan
Status
On
Smoke
Detector/
FA Relay
Smoke Detector/
FA Digital In
14 15
Powered Contact OutputsDry Contact Inputs (From Field)Power Input
1 8
24V COM
Actuator Power
Status Relay
Digital inputs to controller
Smoke / Fire Alarm DI
Fan Safety
Fan
Master
Relay
Fan Status
Digital In
16 17
8A @ 24Vac/dc
R4 FS-S
16
Fan Status DI
17
R1 LL-A
10
Low Limit DI
11
R2 SP-A
12
Static Press Alarm DI
13
R3 Smoke/Fire Alarm
14
15
RIBMNLB (Track Mount)
RIBLB (Enclosed)
1 9
24V COM
Dry Contact Output
10A @ 277 Vac 10A @ 30 Vdc 1/2 HP@120/240Vac B300 Pilot Duty
Master
Relay On
CAN BE USED TO
ISOLATE FIELD DEVICES
FROM EACH OTHER AND
FROM CONTROLLER,
NOT ONLY FAN CIRCUITS
Panel Field
5Amp
DC-1 Power
24Vac COM
DL-1
PB-1
R1 LL-A
RC-1
TX-1
24Vac
DC-1 DO-3
R1 LL-A R2 SP-A R3 SMK/FA
R1 LL-A
Black
Black
1 2
24Vac 24Vac
At power-up, delay 2 sec before DL-1 becomes activated
R2 SP-A
R3 SMK/FA
R4 FS-S
R4 FS-S
DL-1
White
White
Green
Made in USA
Meets
Buy American
of ARRA 2009
CODE VER. 1.0
120Vac
H N
Emergency Power
G
with ground
Starter
Contactor
To Motor
Status
FS-S
Fan Status
X2X1
Ols
120Vac
O
Blu
Yel
Org Gry
Prp
Brn
Low Limit
Static Pressure
Smoke Detector / Fire Alarm
H A
T
n
RIBX Series
1 x 21 x 1
RIBTU2C
Wht/Blu
Wht/Yel Gry/Wht
Wht/Prp
1
9
3
4
1
5
1
6
1
7
1
8
Fan Safety Relay
Actuator Power
This drawing represents:
Only Low Limit Latch Set
J1 Jumper Not Installed
071417
Loading...