Johnson Controls MAP Quick Start Manual

© 2016 Johnson Controls, Inc.

Part No. 24-10737-16, Rev. E

Mobile Access Portal (MAP) Gateway

MAP Gateway is a pocket-sized web server that lever­ages the power of mobile connectivity to maximize pro­ductivity for daily operations.

• Commission, configure and access building automa­tion equipment using Wi-Fi-enabled devices such as
smart phones, tablets, and laptops.

• Change and configure setpoints,
parameters and schedules. View alarms and trends
through an HTML5 browser-based interface.

Use as a portable device (and carry from site to site as
needed) or permanently mount on site.

IMPORTANT: Keep your MAP Gateway in the protec­tive shell or stationary cradle with which it shipped.
This may help protect the unit if it is dropped.

IMPORTANT: Save this guide. It contains default
user name and password information that may be
needed to reset your MAP Gateway to factory
defaults.

European Single Point of
Contact:

NA/SA Single Point of Contact:

JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY

JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA

APAC Single Point of Contact:

JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 22 BLOCK D NEW DISTRICT
WUXI JIANGSU PROVINCE 214142
CHINA

QUICK START GUIDE

Mobile Access
Portal Gateway

Optional - Ethernet Setup

a. In the MAP Gateway UI, navigate to

Settings > Ethernet.

b. In the Ethernet drop-down list, select On to

enable the MAP Gateway Ethernet port.
c. Click Save on the bottom of the screen.
d. Note the address in the IP Address field.

By default, the MAP Gateway is configured

to dynamically receive an IP address from

your network using DHCP. If the IP

address does not appear, refresh the

screen.
e. Enter this IP address in your browser

address bar to access the MAP Gateway

over an Ethernet network.

Refer to the Mobile Access Portal Gateway

Network and IT Guidance Technical Bulletin
(LIT-12012015) for more options.

Use the MAP Gateway

Select a device from the equipment list

and use the web pages from the MAP
Gateway to view, commission and configure
devices as needed.

IMPORTANT: The MAP Gateway must be
plugged into external power for Ethernet
use. Get approval from the site’s
IT Administrator before connecting to the
Ethernet network.

6

7

GETTING STARTED

Refer to the Mobile Access Portal Gateway Installation Instructions (Part No. 24-10737-8) for important product application information.

Connect the MAP Gateway to

Equipment

If you are going to use the MAP
Gateway on Ethernet, you must plug it into
external power before you attach the field
bus adapter.

Use the supplied RJ-12 cable or field bus
adapter to connect the RS-485 port of the
MAP Gateway to the sensor bus or field bus
port of the equipment controller.

The MAP Gateway LEDs
flash, indicating that the
device is initializing. When
the Fault LED turns off
and the Wi-Fi LEDs flash
in succession, the
MAP Gateway is ready to
use.

1

Connect to the MAP Gateway
Wi-Fi Network

In the Wi-Fi settings of your mobile
device or laptop, connect to the MAP Gateway
Wi-Fi network using the following default
credentials:

Open a Web Browser

Direct your browser to
www.mapgwy.com to open the MAP Gateway

browser interface.

MAP Gateway ships with a private
mapgwy.com SSL certificate installed to ensure
secure communication with the MAP Gateway.
However, this certificate does not indicate that
it is trusted in a browser. If you wish to install
your own certificate, refer to Installing a

Security Certificate on a Client That is
Connecting to MAP Gateway in the Mobile
Access Portal Gateway Network and IT
Guidance Technical Bulletin (LIT-12012015) for

more information.

Log in to the MAP Gateway

Use the following default Admin login

credentials:

2

Place Label

Here.

SSID:

Passphrase:

3

4

Read and accept the MAP Gateway license
agreement.

Change Passwords

The first time you log in to the MAP
Gateway, the Change Password and
Passphrase web page appears. You must
change the Admin password and Wi-Fi
passphrase.

a. Replace the default password in the New

Admin Password field. Confirm the
change by entering the new password in
the Verify New Admin Password field.

b. Replace the Wi-Fi Passphrase in the New

Wi-Fi Passphrase field and click Save.

Continue to Step 6.

IMPORTANT: After you change the Wi-Fi
passphrase or SSID, the web server
restarts and you must rejoin the MAP

Gateway Wi-Fi network using the new
passphrase. On some mobile devices, you
must select and forget the original MAP
Gateway Wi-Fi network before rejoining the
network with the new passphrase.

Place Label

Here.

User:

Password:

5