Johnson Controls M9106-AGx-2N0x Series Data Sheet

M9106-AGS-2N0x Series

Electric Non-Spring-Return Actuator

Electric Damper Actuators

Code No. LIT-1900119

M9106-AGx-2N0x Series Electric Non-Spring-Return Actuators

Description

The M9106-AGA-2N0x synchronous
motor-driven actuators provide floating
(3-wire) control and are easily installed on a
VAV box. They may also be installed on a
small- to medium-sized damper with a round
shaft up to 1/2 in. (13 mm) in diameter or a
3/8 in. (10 mm) square shaft.

These compact, non-spring-return actuators
have 53 lb·in (6 N·m) running torque in a
compact easy-to-install package. The
actuators are available with either a nominal
60-second travel time at 60 Hz (72 seconds at
50 Hz) or a nominal 120-second travel time at
60 Hz (144 seconds at 50 Hz) for 90° of
rotation.

The M9106-AGS-2N02 Actuator/Transmitter
combines an M9106-AGA-2N02 with a
prewired DPT-2015 Differential Pressure
Transmitter that has a 0 to 1.5 in. W.C.
(0 to 374 Pa) differential pressure range.

Features

• simple direct coupling reduces installation
and commissioning time by eliminating
damper linkages

• whisper quiet 35 dBA rating meets audible
requirements for open ceilings

• long life brushless synchronous drive

• motor technology provides constant
rotation time independent of load

• 100,000 cycle rating, 2,500,000 repositions

• direct shaft mount with single-screw
coupler simplifies installation and provides
3-point shaft gripping

• magnetic clutch provides torque protection
for the actuator gear train and damper

• manual gear release simplifies setup and
field adjustments

Selection Chart

Code Number Control Type Torque / Timing / Voltage Auxiliary Switches Comments

M9106-AGA-2N01 Floating 53 lb·in (6 Nm)

M9106-AGA-2N02 53 lb·in (6 Nm)

M9106-AGS-2N02 53 lb·in (6 Nm)

Applications

The actuators are used to position balancing,
control, round, and zone dampers in typical
HVAC applications. They are also used to
position the blades in a VAV box. The
actuators mount directly to the surface of a
VAV box, round damper, or small rectangular
damper with a single No. 10 self-drilling sheet
metal screw (included). There are no
additional linkages or couplers required.
Clearly labeled electrical terminals simplify
installation. Refer to the damper or VAV box
manufacturer’s information to select the
proper timing for the actuator.

Note: The damper rotation time must be
defined at the controller, and the damper point
definition must match the rotation time of the
actuator.
When combined with a VAV controller, the
actuator provides reliable integrated damper
control. Refer to the M9106-AGx-2N0x Series

Electric Non-Spring-Return Actuators

Application Note (LIT-2681116) for various

configurations with and without the DPT-2015
Differential Pressure Transmitter.

Refer to the M9106-AGx-2N0x Electric

Non-Spring-Return Actuators Product Bulletin

(LIT-2681126) or the M9106-AGx-2N0x

Electric Non-Spring-Return Actuators
Installation Instructions

(Part No. 34-636-1077) for important product

application information.

None Actuator only
60 seconds at 60 Hz
AC 24 V 50/60 Hz

120 seconds at 60 Hz
AC 24 V 50/60 Hz

120 seconds at 60 Hz
AC 24 V 50/60 Hz

Repair Information

If the M9106-AGx-2N0x Series Electric
Actuator fails to operate within its
specifications, replace the unit. For a
replacement actuator, contact the nearest
Johnson Controls® representative.

Actuator includes a DPT- 2015 and
CBL-2000-1

Electric Damper ActuatorsElectric Damper ActuatorsElectric Damper ActuatorsElectric Damper Actuators

The performance specifications are nomina l and con form to accep table ind ustry stand ards. For applicati ons at con ditions be yond these specification s, consult th
Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2014 Johnson Controls, Inc.

V–27

Dimensions, in. (mm)

Electric Damper Actuators

M9106-AGx-2N0x Series Electric Non-Spring-Return Actuators (Continued)

Accessories

Code Number Description

CBL-2000-1 20 in. (0.5 m) wiring harness, UL accepted for plenum use, supplied with the M9106-AGS-2N02 and may be ordered separately; co nnects the

CBL-2000-2 20 in. (0.5 m) plenum rated wiring harness; Underwriters Laboratories, Inc.® (UL) accepted for plenum use; connects the M9101 and

CBL-2000-3 72 in. (1.8 m) plenum rated wiring harness

Electric Damper Actuators

Electric Damper ActuatorsElectric Damper Actuators

DPT-2015-0 0 to 1.5 in. W.C. (0 to 374 Pa) differential pressure transmitter
DMPR-KC003 Blade pin extension without bracket supplied with Johnson Controls CD-1300 dampers and may be ordered separately for all direct-mount

DMPR-KC011 Hex head blade pin extension without bracket
DMPR-KC012 Hex head blade pin extension with bracket
M9000-200 Commissioning tool provides a control signal to drive on/off, floating, proportional, or resistive actuators

Electric Damper Actuators

M9106 and DPT-2015 to the VAV controller

DPT-2015-0 to the VAV controller

applications

The performance specifications are no minal and co nform t o acceptab le ind ustry standar ds. For appl ications at condition s beyond these specifica tions, consult th
Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2014 Johnson Controls, Inc.

V–28