Johnson Controls M9102-AGA-3S Series, M9104-xGA-2S Series, M9104-xGA-3S Series Data Sheet

M9102 Series Electric

Non-Spring-Return Actuator

(5)

1-13/32

(36)

(28)

2-13/16

(71)

4-3/32

(104)

5-5/32

(131)

2-1/4

(57)

(52)

1-1/4

(32)

25/32

(20)

Set Screw

Radius

Clearance

M9102/M9104 Series Electric Non-Spring-Return Actuator

Dimensions, in. (mm)

Electric Damper Actuators

Code No. LIT-1900247

M9102-AGA-2S, -3S and M9104-xGA-2S, -3S Series Electric Non-Spring-Return Actuators

Description

The M9102 and M9104 Series Actuators are direct-mount, non-spring-return electric actuators that operate on AC 24 V power. These synchronous motor-driven actuators provide floating control (AGA), floating control with automatic shutoff (IGA), and proportional control with selectable 0-10 or 2-10 VDC (GGA). The -2S models are equipped with plenum cables, and the -3S models are equipped with terminal blocks.

All models are compact in size and are easily installed on VAV boxes, Variable Volume and Temperature (VVT) two-position zone applications, or small- to medium-sized dampers with a round shaft up to 1/2 in. (13 mm) in diameter or a 3/8 in. (10 mm) square shaft.

The M9102 Series Electric Non-Spring-Return Actuators provide a running torque of 18 lb·in (2 N·m), and the nominal travel time is 30 seconds at 60 Hz (36 seconds at 50 Hz) for 90° of rotation. The M9104 Series Electric Non-Spring-Return Actuators provide a running torque of 35 lb·in (4 N·m), and the nominal travel time is 60 seconds at 60 Hz (72 seconds at 50 Hz) for 90° of rotation.

Refer to the M9102-AGA-2S, -3S and

M9104-xGA-2S, -3S Series Electric Non-Spring-Return Actuators Product Bulletin

(LIT-1201742) for important product

application information.

Features

• Two Torques Available: 18 and 35 lb·in (2 and 4 N·m) — offer the most suitable choice for the specific application.

• Short 30-Second Travel Time Available — provides a quick response for two-position zone applications.

• 35 dBA Nominal Audible Noise Rating — meets the audible noise requirements for open-ceiling environments.

• Synchronous Drive — provides a constant rotation time that is independent of the load.

• 100,000 Cycle Rating — provides years of trouble-free service.

• Direct Shaft Mounting with Single-Screw Coupler — reduces installation time and provides three-point shaft gripping.

• Magnetic Clutch — protects the actuator gear train and the damper from damage due to excessive torque during a stall condition.

• Manual Gear Release — simplifies actuator setup and adjustments in the field.

• Plenum Cable or Screw Terminal Electric Connections — make wiring quick and easy.

The performance specifications are nomina l and con form to accep table ind ustry stand ards. For applicati ons at con ditions be yond these specification s, consult th Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2014 Johnson Controls, Inc.

• Floating, Floating with Timeout, and Proportional 0(2) to 10 VDC Control Inputs Available — offer a full range of control input options.

• Small, Compact Design — allows installation in tight-fitting locations.

Applications

The M9102 and M9104 Series Electric Non-Spring-Return Actuators are designed to position balancing, control, round, and zone dampers in HVAC systems. These electric actuators are also designed to position blades in a VAV box, or they can be used in VVT two-position zone applications.

Each actuator mounts directly to the surface in any convenient orientation using a single No. 10 self-drilling sheet metal screw (included with the actuator). No additional linkages or couplers are required. Electrical connections on the actuator are clearly labeled to simplify installation.

Repair Information

If the M9102 or M9104 Series Electric Actuator fails to operate within its specifications, replace the unit. For a replacement actuator, contact the nearest Johnson Controls® representative.

2-1/16

1-3/32

9/16 (14)

3/16

m i d _ t c a :

G I F

Electric Damper ActuatorsElectric Damper ActuatorsElectric Damper ActuatorsElectric Damper Actuators

V–19

Electric Damper Actuators

M9102-AGA-2S, -3S and M9104-xGA-2S, -3S Series Electric Non-Spring-Return Actuators (Continued)

Selection Chart

Code Number Control Type Running Torque Travel Time Electrical Connections

M9102-AGA-2S Floating 18 lb·in (2 N·m) 30 seconds at 60 Hz 48 in. (1.2 m) UL 444 Type CMP plenum rated cab le with 19AWG

M9102-AGA-3S Floating 18 lb·in (2 N·m) 30 seconds at 60 Hz M3 screw terminals

Electric Damper Actuators

Electric Damper ActuatorsElectric Damper Actuators

M9104-AGA-2S Floating 35 lb·in (4 N·m) 60 seconds at 60 Hz 48 in. (1.2 m) UL 444 Type CMP plenum rated cab le with 19AWG

M9104-AGA-3S Floating 35 lb·in (4 N·m) 60 seconds at 60 Hz M3 screw terminals M9104-IGA-2S Floating or on/off 35 lb·in (4 N·m) 60 seconds at 60 Hz 48 in . (1.2 m) UL 444 Type CMP plenum rated cable with 19AWG

M9104-IGA-3S Floating or on/off 35 lb·in (4 N·m) 60 seconds at 60 Hz M3 screw termina ls M9104-GGA-2S Proportional 35 lb·in (4 N·m) 60 seconds at 60 Hz 48 in. (1.2 m) UL 444 Type CMP plenum rated cab le with 19AWG

M9104-GGA-3S Proportional 35 lb·in (4 N·m) 60 seconds at 60 Hz M3 screw terminals

Accessories

Code Number Description

DMPR-KC003 DMPR-KC010 Adjustable blade position indicator switch kit with tot al switching load limited to 2,000 VA for t he following applications:

DMPR-KC011 Hex head blade pin extension without bracket DMPR-KC012 Hex head blade pin extension without bracket M9000-200 Commissioning tool that provides a control signal to drive 24 V on/off, floating, proportional, and/or resistive electric actuators M9104-100 Connector for 3/8 in. (10 mm) flexible metal conduit (10 per package)

1. Furnished with the damper and may be ordered separately

Electric Damper Actuators

(0.75 mm

7 in. (178 mm) blade pin extension without bracket for Johnson Controls direct-mount damper applications

Pilot duty: AC 24 V, 50 VA; AC 125/250/277 V, 125 VA Motor load: AC 12/250/277 V, 1/3 hp Resistive load: AC 125 V , 11 A; AC 250 V, 8 A; AC 277 V, 7 A (all maximum values)

) conductors and 1/4 in. (6 mm) ferrule ends

The performance specifications are no minal and co nform t o acceptab le ind ustry standar ds. For appl ications at condition s beyond these specifica tions, consult th Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2014 Johnson Controls, Inc.

V–20

+ 1 hidden pages