®
HomeLink
. The integrated ga
V
m
T
r
b
w
www.eurohomelink.com
or s
k
and garage door opener
e
mail:
info@eurohomelink.com
Operating Instructions and
Programming Guidelines
January 2
This document applies s
olkswagen Ho
in the
Take advantage of our se
the reliable link
If you have any questions or
or call our toll-free HomeLin
1, 2008
pecifically to the product
eLink® (Europa)
ouareg
vice –
etween you and us.
ould like further details, go to
us an
Hotline: 008000 466 354 65.
-
Johnson Controls1
Description
The HomeLink system provides a convenient way to replace
f
u
a
s
t
d
Retain the original remote control for fu
d
H
Integration of HomeLink in the Touareg
three remote controls with a single
programming procedures (i.e. new
built-in component. This innovative feature learns the radio
controls used to activate garage doors, property gates, sec
For more information on HomeLink and/or HomeLink comp
Hotline 008000 466 354 65 or refer to the HomeLink Web
Precautions
When programming the HomeLink sys
make sure that people and objects are
harm or damage, in particular injuries
!
vehicle purchase). It is also suggested
programmed HomeLink buttons shoul
(please refer to Erasing Programmed
up to
requency codes of most current remote
rity systems, and home or office lighting.
tible products, call our toll-free HomeLink
ite www.eurohomelink.com
em to a gate or garage door opener,
out of the way to prevent potential
ue to trapped limbs.
that upon the sale of the vehicle, the
be erased for security purposes
omeLink Buttons ).
Fig. 1
The control panel for the HomeLink system
is located in the overhead console of your
Touareg (fig.1).
1)
Angaben Fahrzeugseite beziehen sich auf die Fahrtrichtung
Fig. 2
The transmitter unit is located in the
overhead console, directly in front of the
third sun visor (fig. 2).
Johnson Controls2
Programming
When programming the HomeLink system the bes
e
c
c
k
h
m
a
y
HomeLink button (fig. 4)
rapidly, release both buttons
results are achieved if new batteries
!
are inserted into the remote control for the garag
HomeLink can be programmed in just one minute, after whi
Garage doors and property gates can be opened at the tou
Please follow the safety instructions and apply the handbra
engine!
1. Press and hold the two outside buttons I and
III (fig. 3) - releasing only when the diode begins to
flash after approximately 20 second s.
Note: This procedure erases the factory-set
default codes and does not have to be followed
to program the other HomeLink
®
buttons.
2. Hold the original remote control of the device you wis
from the HomeLink transmitter unit keeping the diode
The distance between the remote control and the Ho
system being programmed. You may require several
each setting position for at least 15 seconds before tr
door opener.
h all functions can be used immediately.
h of a button.
e. Switch on the ignition. Do not start the
to train at a distance of 5-30 cm away
in view all the time.
eLink transmitter unit depends on the
ttempts at different distances. Maintain
ing out another.
Fig. 3
3. Using both hands, simultaneously push the
remote control button and the desired
.
Do not release the buttons until step 4
has been completed.
4. The HomeLink diode will flash, first slowly
and then rapidly. When the diode flashes
.
The rapid flashing light indicates successful
programming of the new frequency signal.
To program the remaining two buttons, follow steps 2 to 4.
Fig. 4
Johnson Controls3
Operating HomeLink
The vehicle should be within the operating range of the gate
r
t
s
e
t
b
s
constantly for two seconds. This pattern repeats itse
h
r
t
garage door opener and the ignition
r
for up to 20 seconds
should be switched on. The HomeLink system operates the
device) in exactly the same way as the original remote cont
When you have programmed the HomeLink
system, press the appropriate button I, II, or
III on the control panel to activate the gate or
garage door opener (fig. 5).
The diode will light up when you press the
button on the control panel.
or
gate or garage door opener (or other
ol.
For convenience, the original remote control
of the device may also be used at any time.
In the case of a standard code, the HomeLink diode is cons
transmission process. For use with compatible systems, no
If HomeLink now does not operate your sy
!
has a rolling code feature. You will find adv
Synchronisation
Rolling Code Synchronisation
You need to check by going through the following steps wh
opener (or other device) is equipped with a rolling code fea
Look in your gate or garage door opener manual fo
The remote control appears to program HomeLink
opener.
Fig. 5
antly illuminated throughout the
further action is necessary.
tem, this may be because your original remote control
ice about this in the section on Rolling Code
ther or not your gate or garage door
ure.
clarification.
ut HomeLink does not operate the gate or garage door
Press and hold down the programmed HomeLink b
With a rolling code system, the HomeLink diode fla
If HomeLink was programmed with a rolling code system, t
period it must be synchronised with this system again befo
Follow the instructions below for Rolling Code Synchronisa
with a second person to help).
Johnson Controls4
utton.
hes quickly for a short time and then stays on
.
en after the end of the programming
e it will function properly.
ion (the procedure will take less time
Rolling Code Synchronisation
Your vehicle must be within operating range of the gate or g
u
g
e
d
s
e
H
e
e
2.
When the diode begins to flash slowly (after
door opener and the ignition should
be switched on. Make sure you comply with the safety instr
rolling code.
ctions even when synchronising the
1. Locate the training button (programming button) on th
unit. Exact location and colour of the button may vary
(refer to the operating instructions of the gate or gara
remote controls”).
2. Press the training button (programming button) on th
unit (which will usually activate a “training” light).
Note: Following step 2, there are typically 30 secon
3. Firmly press and release the programmed HomeLink
button a second time to complete the training proces
may
require you to do this procedure a third time to compl
The gate or garage door opener should now recognise the
HomeLink button is pressed.
The remaining two buttons may now be programmed if this
Please refer to Programming.
Reprogramming a Single HomeLink Button
If a HomeLink button has been programmed to activate a d
to operate a different device, proceed as follows. This proc
of the respective HomeLink button.
e gate or garage door opener motor head
by gate or garage door opener brand
e door opener “Training additional
gate or garage door opener motor head
s in which to initiate step 3.
button. Press and release the HomeLink
. (Some gate or garage door openers
te the training).
omeLink signal and activate when the
has not previously been done.
vice, and you now wish to use this button
dure will erase the existing programming
1. Press the appropriate HomeLink button
I, II, or III which you want to program
and keep holding it for about 20 seconds
until the diode starts flashing slowly (fig.6).
Do not release until step 4 has been
completed.
approximately 20 seconds), hold the remote
control of the device you wish to train approx.
5-30 cm away from the HomeLink transmitter
unit - keeping the diode in view.
Fig. 6
Johnson Controls5
Reprogramming a Single HomeLink Button
k
o
is now erased and the new system is ready for operation
d
a
2.Release both buttons
A
s
the programming in the HomeLink
system before selling you
The distance between the remote control and the HomeLin
system being learned. You may require several attempts at
setting position for at least 15 seconds before trying out an
3. Now activate (press) the remote control
and keep it pressed (fig.7).
4. The HomeLink diode will flash, first slowly
and then rapidly. When the diode begins to
flash rapidly, release both buttons.
The system previously programmed into HomeLink
.
This process has no effect on the other HomeLink buttons.
Erasing Programmed HomeLink Buttons
The HomeLink buttons can simply be reprogrammed indivi
To erase the existing programming from all three buttons, c
transmitter unit depends on the
different distances. Maintain each
ther.
Fig. 7
ually but not individually erased.
rry out the following:
1. Press and hold the two outside buttons I and III
until the diode begins to flash after approximately
20 seconds (fig. 8).
.
The HomeLink system is now in setting mode (training
mode) and can be reprogrammed at any time (see steps
2 to 4 in the section Programming).
Note:
s a security precaution we recommend that you era
vehicle.
Fig. 8
e
Johnson Controls6
Technical Information for OEM Service
Diag
t
n
o
y
n
w
o
start
aga
equivale
sta t as g aga e u be o as es s equ ae
e
hold
button
few seconds later, the diode will sta
k
u
A
o
:
y
a
a
t
you
flashing again. The number
nostics
If, after carefully reading and following the above instruction
your original remote control, assistance is available via our
Before you call, please make sure that you have the followi
reference. The Hotline operators will need this information t
Procedure for obtaining diagnostic information directl
(Note that these steps, carefully followed, will not erase you
1. To determine the Software Revision of your HomeLi
I or III, (but NOT both!) for about 100 seconds, at
and turn completely off. Continue to press the butt
flashing
HomeLinksystem.
For example, seven flashes would mean R
2. To determine the Region Code status of your HomeL
button II for about 100 seconds, until the diode exti
of flashes will indicate the Region that your HomeLin
to operate in. For example:
in. The number of flashes is
II. A
s, you still cannot successfully train your HomeLink to
oll-free Customer Service Hotline 008000 466 35465.
g HomeLink Diagnostic Information available for
assist you with any difficulties you may have.
from your HomeLink:
r programmed HomeLink channels).
k press and continue to hold button
hich point the diode will stop flashing
n. A few seconds later, the diode will
nt to the software version of
vision 7.0.
ink, press and continue to hold
nguishes and remains off. Continue to
system has been factory programmed
r
One Flash = Rest of E
Two Flashes = France
Three Flashes = U.K.
Four Flashes = Italy
3.
The Software Revisionand Region Code status are especi
Please take a moment to gather the information outlined in
dditionally, the Hotline will request from you the foll
and the original transmitter you are trying to program
A. Make and model of your vehicle, including
of purchase;
B. Original remote control brand, model, age
rope
wing information about your vehicle
ear of manufacture and country
nd operating frequency, if known.
lly important for solving training issues.
he above three steps before you call the Hotline.
Johnson Controls7
Loading...