Code No. LIT-1900768
FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter
with Johnson Controls TE-6300 Series
Temperature Sensor (Order Separately)
Issued March 29, 2012
FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter
Description
The FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter is
designed to operate with a TE-6300 Series 10k ohm
Johnson Controls® Type II Thermistor Sensor (order separately), to
sense the temperature in warmer applications up to 158°F (70°C) and
transmit wireless temperature data to a receiver or controller. Ideal
applications include data server racks, food warming ovens, warming
baths, warm food storage units, and hospital neonatal incubators.
In an FX-ZFR1800 Series Wireless Field Bus System (mesh network)
application, the transmitter communicates with FX-PCG16 Series,
FX-PCG26 Series, and FX-PCV16 Series Controllers by means of the
FX-ZFR1811 Router.
An FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter
can also be used in a One-to-One application (non-mesh network) to
communicate with an FX-WRZ7850-0 Wireless Receiver. The
FX-WRZ7850-0 Receiver transfers data to the controller by means of
the Sensor Actuator (SA) Bus. In a typical application, one
FX-WRZRMT10K-0 Transmitter reports to one FX-WRZ7850-0
Receiver, but up to five FX-WRZRMT10K-0 Transmitters can be
associated with a single FX-WRZ7850-0 Receiver in averaging
applications.
The FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter
can transmit sensed temperature and low battery conditions to an
associated router or receiver. The FX-WRZRMT10K-0 Transmitter and
associated TE-6300 Series Temperature Sensor are designed for
indoor, intra-building applications only.
Refer to the FX-WRZRMT10K-0 Wireless Remote Temperature
Transmitter Product Bulletin (LIT-12011767) for important product
application information.
Features
• Facility Explorer design — leverages the Facility Explorer
Web-based platform to provide wireless temperature data
transmission to a field device across the network
• application mobility and flexibility — provides a wireless alternative
to hard-wired counterparts, and facilitates easy initial location and
relocation of the temperature transmitter and the associated
temperature sensor
• One-to-One wireless non-mesh network communication — enables
quick, economical, and low-maintenance installation, which
reduces overall installed costs
• wireless mesh network communication — enhances reliability
through automatically forming wireless links and redundant wireless
data transmission paths
• temperature monitoring/temperature range deviation alarm
system — replaces manual daily temperature monitoring with
continuous electronic temperature monitoring
• high degree of temperature system accuracy — allows the
temperature transmitter and the associated temperature sensor to
monitor temperature-sensitive applications over a range of 32 to
158°F (0 to 70°C)
• Liquid Crystal Display (LCD) — indicates real-time status of the
environment
• Fahrenheit/Celsius (°F/°C) button — toggles the display
temperature between degrees Celsius and degrees Fahrenheit
• temperature sensor connects to the associated temperature
transmitter in the field — ensures that the temperature sensor can
be easily replaced if needed
Repair Information
If the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter
fails to operate within its specifications, replace the unit. For a
replacement transmitter, contact the nearest Johnson Controls
representative.
The two AA alkaline batteries supplied with the FX-WRZRMT10K-0
Wireless Remote Temperature Transmitter typically have a life of
5 years or more. The transmitter reports a low battery condition to the
receiver or controller, which relays the low battery condition to the
Facility Explorer system. The low battery condition is also shown on the
LCD on the face of the transmitter.
Replace the transmitter batteries with two high-quality AA alkaline
batteries as necessary, ensuring that the batteries are installed in the
proper polarity.
When replacing batteries, both batteries should be replaced at the
same time. Batteries removed from this device must be recycled or
disposed of in accordance with local, national, and regional
regulations. Only certified technicians or qualified building
maintenance personnel should service Johnson Controls products.
Lithium batteries with a maximum cell voltage of 1.5 volts can be
substituted to extend the period between replacing the batteries.
Do not mix lithium and alkaline batteries in this device.
The performance specifications are nomina l and conf orm to accep table industr y standar ds. For ap plications a t condition s beyond th ese specification s, consult the local Johnson Controls o ffice.
Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2012 Johnson Controls, Inc.
www.johnsoncontrols.com
1 of 3
FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter (Continued)
FX-WRZRMT10K-0 and TE-6300 Dimensions and Physical Features, in./mm
Signal
Test Button
Set Screw
80
to Front of
Protrusion
4-23/32
Button
Back of Base
3-5/32
3
76
1/4 in. (6 mm)
Outside Diameter
10 ft (3 m)
Plenum - R a t ed Cable
Selection Chart
Ordering Information
Code Number
FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter: Includes One Temperature Transmitter Assembly (One Transmitter,
TE-6361A-1 Johnson Controls 10k ohm Type II Thermistor Sensor;
TE-6361V-2 Johnson Controls 10k ohm Type II Thermistor Sensor;
TE-636GV-2 Johnson Controls 10k ohm Type II Thermistor Sensor;
TE-636S-1 Johnson Controls 10k ohm Type II Thermistor Sensor;
FX-WRZSST-110 Wireless Sensing System Tool: For Use with an FX-WRZRMT10K-0 Wir eless Remote Temperature T ransmitter , to
MAGNET-BASE-PLW Magnetic Backplate for Mounting the Transmitter on Metal Surfaces; 5 Magnetic Backplates per Package
T-4000-119 Allen-Head Adjustment T ool: 1/16 in. (1.6 mm), for the Tampe r-Resistant Set Screw That Secures the Temp erature
Description
One Mounting Base, and Str i ps of Double-Sided Adhesive Foam Tape; All Factory Assemb led), One Strain Relief
Bushing, One DIP Switch Overlay for a Mesh Network Application Using an FX-ZFR1811 Router, One DIP Switch
Overlay for a Non-mesh Network One-to-One Application Using an FX-WRZ7850-0 Receiver, One Installation
Instructions Sheet, and Two AA Alkaline Batteries
8 in. (203 mm) Duct Probe, Adjustable Enclosure
8 in. (203 mm) Duct Probe, Flange Mount Enclosure
4 in. (102 mm) Duct Probe, Flange Mount Enclosure
Strap-Mount Probe
Function as a Site Survey Tool for the FX-WRZ Series One-to-One Wirele ss Room Sensin g S yst em, o r f or the FXZFR1800 Wireless Field Bus System
Transmitter to the Mounting Base; 30 Tools per Package
Technical Specifications
FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter (Part 1 of 2)
Power Requirements 3 VDC Supplied by Two 1.5 VDC AA Alkaline Batteries (Included with Transmitter);
Addressing DIP Switches (Field Adjustable):
Transmitter Ambient Conditions Operating: 23 to 111°F (-5 to 44° C), 5 to 95% RH, Noncondensing
The performance specifications are nomina l and conf orm to accep table industr y standar ds. For ap plications a t condition s beyond th ese specification s, consult the local Johnson Controls o ffice.
Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2012 Johnson Controls, Inc.
Typical Battery Life: 5 Years or More; 7 Years Using Lithiu m Batteries
MS/TP Address, Network Number, and Zone Address
Storage:
-4 to 140°F (-20 to 60°C), 5 to 95% RH, Noncondensing
www.johnsoncontrols.com
2 of 3