Johnson Controls CTD Series Catalog Page

CTD Series

Analog Output

Input Current

CTD-C2G00-1

5 VDC

0 VDC

0 A 30/60/

120 A

Analog O utput

Input Current

CTD-C3H00-1

10 VDC

0 VDC

0 A

20/100/ 150 A

Analog Output

Input Current

CTD-C1G00-1

20 mA

4 mA

0 A 30/60/

120 A

Linear Outputs

CTD Current Transducers

Current Transducer Devices

Code No. LIT-1900751 Issued July 28, 2011

Description

The Current Transducer Device (CTD) Series of analog output current transducers are nonintrusive devices designed to monitor current flowing through a cable or wire. These units are a cost-effective solution for monitoring load or proof of operation. The current transducers are ideal for monitoring current loads on pumps, driving fans, and blowers, and sensing the status of heating coils and lighting. CTD devices used for load trending over time are effective sensors for predictive maintenance programs.

These units are available with standard 4 to 20 mA current loop, 0 to 5 VDC, and 0 to 10 VDC analog output. The voltage output models derive excitation by magnetic induction from the current-carrying conductor (wire or cable), making these units completely self-powered. The current loop output model requires a 24 VDC power supply.

Optional command relays (CR-01200-0 and CR-02400-0) provide externally controlled auxiliary contacts when used with the current transducers. The relays offer a cost-effective solution for switching loads that require higher power levels than the rating of the current switch contacts, or the need to mount an external relay elsewhere in the control enclosure.

Refer to the CTD Series Current Transducer Devices Product Bulletin (LIT-12011714) for important product application information.

Features

• clamped/split core design — reduces installation time and associated costs

• slide switch, selectable amperage ranges — provides a wide array of amperage ranges to match the application

• multiple outputs: 4 to 20 mA, 0 to 5 VDC, or 0 to 10 VDC — provide the appropriate output for the specific application

• snap-on power relay — provides an easy way to add an external relay to the current sensor

• relay (optional) LED indication Off/On status — allows you to easily check the relay’s on/off status

Repair Information

If the CTD transducers fail to operate within its specifications, replace the unit. For a replacement enclosure, contact the nearest Johnson Controls® representative.

Ordering Information

Product Ordering

Product Code Number

CTD-C1G00-1 Split/Clamped 30/60/120 A 4 to 20 mA CTD-C2G00-1 Split/Clamped 30/60/120 A 0 to 5 VDC With Optional Relay CTD-C3H00-1 Split/Clamped 20/100/150 A 0 to 10 VDC With Optional Relay

1. Requires a 24 VDC/25 mA external power supply.

2. The relay is an accessory.

Accessories

Product Code Number Product Code Description

CR-01200-0 CR-02400-0

1. Refer to the Command Relay Installat i on Instructions (Part No. 24-10345-50) for more information regarding the command relays.

The performance specifications are nomina l and conf orm to accep table industr y standar ds. For ap plications a t condition s beyond th ese specification s, consult the local Johnson Controls o ffice. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2011 Johnson Controls, Inc.

1 1

Core Type Multi Range Output Signal LED Display Relay

With Optional Relay

12 VAC/VDC Single-Pole, Single-Throw (SPST), Normally Open (N.O.) Relay 24 VAC/VDC SPST, N.O. Relay

1 of 2

2 2 2

Snap-On Accessory Snap-On Accessory Snap-On Accessory

www.johnsoncontrols.com

Current Transducer Devices (Continued)

Technical Specifications

CTD Series Current Transducer Devices

Current Range (Selectable) 30/60/120 A 30/60/120 A 20/100/150 A Maximum Continuous Operating Current 30/60/120 A 30/60/120 A 20/100/150 A Output 4 to 20 mA 0 to 5 VDC 0 to 10 VDC Accuracy ±2.0% Full Scale from 10% to 100% of Selected Range Relay with LED Indicator Available Accessory Response Time 2 Seconds to 100% of Selected Range Sensor Supply Voltage 24 VDC (18 to 30 VDC) Self-Powered Self-Powered Wire Size 12 to 22 AWG (2.1 to 0.6 mm) Diameter Recommended Isolation Voltage 600 VAC rms Temperature Range 5 to 140°F (-15 to 60°C) Frequency Range 50/60 Hz Humidity Range 0 to 95% RH, Noncondensing Screw Torque 4 lb·in (0.5 N·m) Dimensions 2-23/32 x 2-9/16 x 1-1/16 in. (69 x 65 x 27 mm) Aperture (Sensing Hole) Size 23/32 in. x 13/16 in. (18 x 20 mm Diameter) Compliance United States UL Listed, File E310692, CCN NRNT, Under UL 508, Industrial Control Equipment

Shipping Weight 0.35 lb (0.16 kg)

Product Code CTD-C1G00-1 CTD-C2G00-1 CTD-C3H00-1

Canada UL Listed, File E310692, CCN NRNT7, Under CAN/CSA C22.2 No. 14-05

Europe CE Mark – Johnson Controls, Inc., declares that this product is in compliance with the essential requirements and

Industrial Control Equipment

other relevant provisions of the EMC Directive 2004/108/EC and the Low Voltage Directive 2006/95/EC.

The performance specifications are no minal a nd conform t o accept able ind ustry stand ards. For app lication s at condi tions be yond these specifications, cons ult the local Johnso n Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2011 Johnson Controls, Inc.

www.johnsoncontrols.com

2 of 2