Johnson T7000 Owner's Manual

Page 1

JOHNSON TREADMILL T7000

T7000

OWNER'S MANUAL

Johnson Health Tech. Co., Ltd.

No.26, Ching Chuan Rd., Taya Hsiang, Taichung Hsien 428, Taiwan, R.O.C. TEL: +886-4-25667100 FAX: +886-4-25683456 E-mail: sales@johnsonfitness.com http://www.johnsonfitness.com

Page 2

T7000 OWNER'S MANUAL

TABLE OF CONTENTS

MEMO

Part 1. INTRODUCTION 02

Part 2. IMPORTANT SAFETY INSTRUCTIONS

•Proper Usage

•Check For Damaged Parts

•Grounding Instructions

•Safety Instructions

•Children Safety Instructions

•Other Safety Tips

Part 3. SETUP THE TREADMILL

•Getting Stared

•Making A Choice Of Site

•Electrical Power Requirement

•Unpacking The Treadmill

Part 4. ASSEMBLY

•Attention!

•Assembly Instructions

..........................................................................................

.............................................................................

......................................

................................................................

Part 5. OPERATING T7000

•Display Console Descriptions

•Function of Keys

•Display Prompt Value

•Workout Overviews

•Workout Setup Steps

.........................................................................

Part 6. MANAGER'S CUSTOM SETTING

•The List of Manager's Custom Setting

Part 7. MAINTENANCE

•Recommedded Cleaning Tips

•Centering The Belt

................................................................................

Part 8. PRODUCT SPECIFICATIONS

•Tensioning The Belt

................................................

........................................................

JOHNSON COMMERCIAL TREADMILL

Page 3

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

Part 1. INTRODUCTION

This Owner’s Manual describes the functions of the following product: Johnson Fitness Treadmill - T7000 (See "Specifications" in this manual for product specific features), the Johnson Treadmill T7000 is intended for commercial use.

It is recommended that all users of Johnson Fitness exercise equipment should be informed of the following information prior to its use.

When using the Johnson treadmill, always follow basic precautions:

• To ensure your safety and to protect the unit, read all the instructions before assembling and using the treadmill.

• To ensure the proper use and safety of the treadmill, make sure that all users read this manual. Please make this manual a part of your facility’s training program. Remind the users that before undertaking any fitness programme, they should obtain complete physical examinations from their physicians. If, at any time while exercising, the user experiences dizziness, pain, or shortness of breath, nausea or feels faint he or she must stop immediately.

SAVE THIS OWNER’S MANUAL FOR FUTURE REFERENCE.

Part 2. IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE ALL INSTRUCTIONS before assembling or using the treadmill.

•PROPER USAGE

• Do not use the equipment in any way other than designed or intended by the manufacturer.

• It is imperative that all Johnson Fitness Treadmills are used properly to avoid injury.

• Keep hands and feet clear at all times from moving parts to avoid injury.

• Unsupervised children must be kept away from this equipment.

• Do not wear dangling or loose clothing while on equipment.

•CHECK FOR DAMAGED PARTS

• DO NOT use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by Johnson Fitness or authorised dealers.

• MAINTAIN LABELS AND NAMEPLATES. Do not remove labels for any reason. They contain important information. If unreadable or missing, contact Johnson Fitness or authorised dealers for a replacement.

• MAINTAIN ALL EQUIPMENT Preventative maintenance is the key to smooth operating equipment as well as keeping the users liability to a minimum. Equipment needs to be inspected at regular intervals. Defective components must be replaced immediately. Improperly working equipment must be kept out of use until it is repaired.

• Ensure that any person making adjustments or performing maintenance or repair of any kind is qualified to do so. Johnson Fitness or authorized dealers will provide service and maintenance training at our corporate facility upon request or in the field if proper arrangements are made.

CAUTION: Any changes or modifications to this equipment could

void the product warranty.

It is strongly recommended to take the following safety instructions.

JOHNSON COMMERCIAL TREADMILL

•GROUNDING INSTRUCTIONS

This Johnson Fitness product must be properly grounded. If the product malfunctions or breaks down, proper grounding provides a path of least resistance for the electric current, which reduces the risk of electrical shock to anyone touching or using the equipment. This product is equipped with an electrical cord, which includes an equipment grounding conductor and a grounding plug. The plug must be inserted into an outlet that has been properly installed and grounded in accordance with all local codes and ordinances.

JOHNSON COMMERCIAL TREADMILL

Page 4

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

DANGER - Improper connection of the equipment-grounding conductor can result

in a risk of electric shock.

Check with a qualified electrician or service provider if you are in doubt as to whether or not the product is properly grounded. DO NOT modify the plug provided with the product. If it will not fit an electrical outlet, have a proper outlet installed by a qualified electrician. Any modification to the electrical plug will result in a voided warranty.

This product is for use on an indicated voltage circuit, and has a grounding plug that looks like the plug illustrated in sketch as below. A temporary adapter that looks like the adapter illustrated below may be used to connect this plug to a 2-pole receptacle as shown, if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green coloured rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw.

Keep the power cord away from heated surfaces. Do not pull the equipment by the power

•

cord or use the cord as a handle. Never place the power cord under carpeting or place any object on top of the power cord.

•Never drop or insert any object into any opening in the product. If an object should drop

inside, turn off the power, unplug the power cord from the outlet, and carefully retrieve it. If the item cannot be reached, contact Johnson Fitness Customer Support Services.

•Do not use the product outdoors or in areas of high humidity.

•To disconnect, turn the switch to the off position, then remove the plug from the outlet.

•Only use the power cord provided with your Johnson treadmill.

•Never place the power cord under carpeting or place any object on top of the power cord.

•Do not remove the treadmill motor covers or roller covers. Service should be performed only

by an authorised Johnson dealer.

•Unplug your Johnson Treadmill before moving it.

•Close supervision is necessary when used near children, invalids or disabled people.

•

Use care when getting on or off the treadmill. Use the stationary handrails whenever possible. Place your feet firmly on the right and left side platforms before the running belt begins moving (prior to a workout). Step onto the running belt when the speed is at or below 1 mph (1.6 kph).

•SAFETY INSTRUCTIONS

When using an electrical product, basic precautions should always be followed, including the following:

•DANGER : To reduce the risk of electrical shock, always unplug this Johnson Fitness

product before cleaning or attempting any maintenance activity.

•WARNING : To reduce the risk of burns, fire, electric shock, or injury, it is imperative to

connect each product to a properly grounded electrical outlet.

•WARNING : Risk of injury to person - to avoid injury stand on the side rail before starting

the treadmill.

•Be sure the emergency stop pull cord is clipped to user and in a proper placed position on

the user before beginning any workout.

•Use this treadmill for its intended purpose as described in this manual. Do not use

attachments that have not been recommended by the manufacturer.

•Never operate this treadmill if it has a damaged cord or plug, if it is not working properly, if it

has been damaged, or immersed in water. Return the treadmill to a dealer for examination and repair.

•CHILDREN SAFETY INSTRUCTIONS

•Keep children off your Johnson Treadmill at all times.

•When Johnson Treadmill is in use, young children and pets should be kept at least 10 feet

away.

•When it is necessary to immobilize the treadmill, set the display to read "CHOOSE PROGRAM

THEN PRESS ENTER". Then hold down the “RESET” & “ENTER” keys at the same time. The treadmill will now display "IMMOBILIZED". In this state, the treadmill can not be operated. Both the drive motor & elevation motor are disabled. The treadmill will remain in this state across power cycles, resets, etc. To return to normal operation mode repeat the same key sequence, hold down the “RESET” & “ENTER” keys. The treadmill will display "CHOOSE PROGRAM THEN PRESS ENTER" again.

•OTHER SAFETY TIPS

•CAUTION!

exercising immediately and consult your physician before continuing.

•

Do not use the Johnson Treadmill in or near water, where there is moisture on the floor,

 or near a swimming pool.

•

Do not turn the belt by hand.

•

Do not wear any clothing that might catch on any moving parts of this treadmill.

•

Do not reach into, or underneath, the unit or tip it on its side during operation.

•

Never walk or jog backwards on the treadmill.

•

Read this manual before operating this Treadmill.

If you experience chest pains, nausea, dizziness or shortness of breath, stop

04 05

JOHNSON COMMERCIAL TREADMILL

Page 5

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

Part 3.

•

GETTING STARTED

Read the Owners Manual before setting up the Johnson Fitness Treadmill. Place the treadmill where it will be used before beginning the setup procedure.

MAKING A CHOICE OF SITE

•

The site that you select for your treadmill should be well-lit and well ventilated. Locate the T7000 on a structurally solid and flat surface a few feet from the wall or any equipment (Allow a distance of 21 centimeters, or eight inches, between the treadmill and other units on either side. Allow an area of two meters in length by 1 meter in width, or six feet by 3 feet, from the rear of the treadmill to any object or surface.) If the site has a heavy plush carpet, to protect the carpeting and machinery, you should place a rigid plastic base under the treadmill.

Please do not place the treadmill in an area of high humidity, such as the vicinity of a steam room, indoor pool, or sauna. Exposure to intensive water vapour or chlorine could adversely affect the electronics, as well as other parts of the machine. To make exercise a desirable daily activity for you, the treadmill should be in an attractive setting.

After placing the unit where it will be used, check its stability. If the treadmill is placed on a slightly, uneven surface, adjusting the adjustable levelers located underneath the base frame can help, but will not compensate for extremely uneven surfaces. To adjust, loosen the nut, and turn the leveler until the rocking motion ceases, and both levelers rest firmly on the floor. Retighten the nut.

SETUP THE TREADMILL

• UNPACKING THE TREADMILL

The treadmill is carefully inspected before shipment so it should arrive in good operating condition. Johnson Fitness ships the unit in the following peices:

Console Set

NOTE: It is extremely important that the levelers be correctly adjusted for proper

operation. An unbalanced unit may cause striding belt misalignment. A bubble level is recommended to ensure proper leveling.

ELECTRICAL POWER REQUIREMENT

•

The Johnson Fitness Treadmill requires a dedicated line according configurations listed in the chart below. It is particularly important

electrical equipment, such as a computer or a TV, shares the same circuit.

Supply Voltage (VAC) Frequency (Hz) Rated Current (Amps)

100 120 200 220 230 240+

50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60Hz

to the electrical

that no sensitive

16A 16A

7.5A

Frame Set

If any of these parts are missing from the package, please contact Johnson Fitness or authorised dealers at once.

Console Mast

Hardware Kit

NOTE: Do not modify the plug provided with this product. If the plug does not fit into an

available electrical outlet, have a proper outlet installed by a qualified electrician.

06 07

JOHNSON COMMERCIAL TREADMILL

Page 6

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

Part 4.

ASSEMBLY

• ATTENTION!

“AFTER INSTALLATION IS COMPLETED, THE TREADMILL WILL NEED TO BE CALIBRATED BY USING THE AUTO CHECK FUNCTION (see MANAGER’S CUSTOM SETTING). IF THIS IS NOT DONE, THE TREADMILL'S SPEED AND INCLINE VALUES MAY INCORRECT AND DAMAGE THE TREADMILL."

DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO CHECK FUNCTION

• ASSEMBLY INSTRUCTIONS

To ensure the correct assembly of the T7000, please carefully follow these steps:

WARNING :

of the following procedure.

Please make sure that the power cord is unplugged during the completion

• ASSEMBLY PARTS AND TOOLS LIST

STEP 1 Remove The Motor Cover

Unscrew the left and right-size screws (Z53) and lift the motor cover off the treadmill and set it aside. See Diagram 1.

Diagram 1

Z53

Drawing Parts No.

AB1 1

AN1

AC1

AC2

Parts Name Quantity Drawing Parts No. Parts Name Quantity

Frame

Set

Console

Set

Left

Console

Mast

Right

Console

Mast

Z53

Z52

Z50

Z51

Z04

Z02

Z01

Z04

Buttonhead Cross Screw

Hex Head

Screw

Flat Hex-

Sockethead

Screw

Wave

Washer

Hex

Wrench

#5l Allen

Key

Cross

Screwdriver

T-Shape

Allen Key

STEP 2 Secure The Left And Right Console Mast

a.Attach the left console mast by placing it into the console mast support bracket and

aligning the mounting holes. Obtain five flat hex-sockethead screws (Z50) from the Hardware Kit. See Diagram 2.

b.Lift up the plastic piece (Q05) attached aside the motor cover. Place 3 screws (Z50) on

the outside and 1 screw (Z50) on the inside and use the #5L Allen key (Z02) to secure the screws, but leave room for adjustments. See Diagram 3.

c.Place a wave washer (Z51) on the screw (Z50) and secure the screw in the front of the

console mast. See Diagram 3.

d.Put down the plastic piece (Q05) on the motor cover. Place 2 screws (Z53) and secure

the screws into the frame. See Diagram 4.

e.Secure the right console mast to follow the above procedure.

08 09

JOHNSON COMMERCIAL TREADMILL

Page 7

Diagram 2

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

Diagram 4

Diagram 3

Z53

Q04

Z50

Z51

Z50

Q05

JOHNSON COMMERCIAL TREADMILL

Page 8

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

STEP 3 Attach The Console To The Console Mast

a.Route the display cable through the right console mast and pull it out of the hole on the

side of the console mast near the frame. Ask an assistant to hold the console in place while you route the cable through the console mast. See Diagram 5.

b.Attach the console to the right and left console mast using four hex-head screws (Z52)

with the hex wrench to secure the screws.

c.Plug the cable connector into its receptacle on the lower board near the motor.

Diagram 5

STEP 4 Replace The Motor Cover

Replace the motor cover on the treadmill using buttonhead cross screws (Z53) with the cross screwdriver (Z01) to secure them. See Diagram 6.

Diagram 6

Z52

Z53

STEP 5 Calibrate The Treadmill

Enter the Manager’s Custom Setting to select P13 AUTO CHECK to calibrate the treadmill’s speed and incline values. After the completion of calibration, press EMERGENCY STOP key to start the treadmill.

JOHNSON COMMERCIAL TREADMILL

Page 9

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

Part 5. OPERATING T7000

1. Without anyone standing on the treadmill, plug the power cord into a dedicated electrical outlet.

2. The On/Off switch for the treadmill is located next to the power supply plug in. Turn the switch

to the on "þ" position to activate the treadmill.

3. Run the treadmill by following the MESSAGE CENTRE instructions to press the Quick Program or Numeric keys for the program setting: Program, Level, Incline, Speed, Time, Weight, Age and Target Heart Rate.

STOP

QUICK START

ENTER

RESET

• FUNCTION OF KEYS:

"Quick Start": To start running the treadmill, the “Quick Start” function is the fastest way to begin a MANUAL workout immediately. "Stop": Press the "Stop" key once to pause the program for 2 minutes. During the 2-minute pause, press the "Start" key to continue running the program, otherwise the machine will reset automatically. Press and hold down the "Stop" key to reset the treadmill. "Emergency Stop": To stop all functions running. "INCLINE and SPEED ARROW keys": Press these keys to increase or decrease the incline of the treadmill deck, or the speed. "Program Quick-Keys": For quick exercise program selections. "Numeric Keys": Press the numbers to input program Time, Weight, Level, Age, Target Heart Rate, Speed and Incline. "Enter": To confirm each entry of workout setup values, as displayed in the MESSAGE CENTRE. "Reset": To clear data not yet entered by the Numeric Keys numbers.

The Treadmill T7000 is equipped with a manual emergency stop system. Use either of the two features described below to stop the treadmill immediately.

1. A circular-shaped STOP magnet is located on the center of the panel between speed and incline keys. A cord with a clip is attached to this magnet. Before starting a workout, attach

the clip to clothing. To stop the striding belt on the treadmill, pull the cord, removing the magnet from the console. Replace the magnet to reset the system.

A massive-shaped EMERGENCY STOP button is located on the center of the crossbar below

the console. Press the button to stop the striding belt and end the current workout.

•

DISPLAY CONSOLE DESCRIPTIONS

1. WORKOUT PROFILE WINDOW: During a workout, intervals, hills and valleys appear in this

window as rows of lights stacked in columns. The number of lit rows within a column corresponds to an incline percentage.

2. MESSAGE CENTER: This window displays step-by-step instructions for setting up a workout. During a workout, it displays Time, Pace, Speed, Distance, Incline, Level, Calories and Calories per minute.

3. HEART RATE CENTRE: This window displays your Actual and Target heart rate during the workout. The console displays a heart rate within 10 to 15 seconds of contact with

the sensors or the use of a heart rate chest strap. In TARGET HEART RATE program, the inputted target heart rate willdisplay in the window every 60 seconds.

•DISPLAY PROMPT VALUE

PROMPT DEFAULT MINIMUM MAXIMUM UNIT

TIME LEVEL WEIGHT AGE SPEED INCLINE

NOTE: The workout time displays “countdown” according to default time or the maximum time that the club owner set. When the workout time input as “0”, the time will count from 0 to the

maximum

time depending on the fitness club setup. The workout pattern repeats until the

maximum workout time is completed.

68/150

30 N/A N/A

34/75

0.8 / 0.5 0

99 10

150/330

20 / 12

minute

kg / lbs

year

kph / mph

JOHNSON COMMERCIAL TREADMILL

Page 10

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

• WORKOUT OVERVIEWS

PROGRA4 DESCRIPTIONS

Manual is a constant effort workout in

MANUAL

INTERVAL

WEIGHT LOSS

FAT BURN

which the user can change incline or speed at any time.

Interval is periods of intense aerobic exercise separated by regular periods of lower-intensity exercise. At any point during the workout, the user can change the settings of the current speed.

Weight Loss is designed to promote weight loss by raising and lowering the elevation. The treadmill automatically adjusts the incline according to the overall time.

Fat Burn is a high-intensity workout for burning the body's fat reserves. The program adjusts the intensity level through changing the elevation, and the user controls the speed during the workout.

DEFAULT

TIME

20 min

PROGRAM

CONTROL

N/A

Elevation

PROMPT INPUT

Time, Weight

Level, Time Weight

• WORKOUT SETUP STEPS

•Quick Start

Press the "Quick Start" key and the WORKOUT PROFILE WINDOW will show "3", "2", "1", "GO!".

The treadmill will start running from the lowest incline and the set-up lowest speed (0.8~2.4kph / 0.5~1.5mph), with the default time counting down from 20 minutes and the

default weight value of 68 kgs (150 lbs).

•Manual

1) Choose the "MANUAL" program using the PROGRAM QUICK-KEYS, and then press ENTER.

2) Choose the "TIME" using the NUMERIC KEYS, and then press ENTER

3) Choose the "WEIGHT" using the NUMERIC KEYS, and then press ENTER

4) Press START.

•Interval, Weight Loss & Fat Burn

1) Choose the "INTERVAL, WEIGHT or FAT BURN" program using the PROGRAM QUICK-KEYS, and then press ENTER.

2) Choose the "LEVEL" using the NUMERIC KEYS, and then press ENTER.

3) Choose the "TIME" using the NUMERIC KEYS, and then press ENTER.

4) Choose the "WEIGHT" using the NUMERIC KEYS, and then press ENTER

5) Press START.

5K RUN

TARGET HR

5K Run is designed to simulate a 5K run with elevation changes. The program completes when the user has completed 5K, so there is no preset time. The user can make speed changes during this program.

Increases endurance by changing speed or elevation, while keeping the user at the target heart rate they set.

N/A

20 min

Elevation

Speed or Elevation

Level, Weight

Age, Target Heart Rate, Max Speed or Max Elevation, Time, Weight

•5K Run

1) Choose the "5K RUN" program using the PROGRAM QUICK-KEYS, then press ENTER.

2) Choose the "LEVEL" using the NUMERIC KEYS, and then press ENTER.

3) Choose the "WEIGHT" using the NUMERIC KEYS, and then press ENTER

4) Press START.

•Target HR

1) Choose the "TARGET HR" program using the PROGRAM QUICK-KEYS, and then press ENTER.

2) Choose your "AGE" using the NUMERIC KEYS, and then press ENTER.

3) Set up your "TARGET HEART RATE" using the NUMERIC KEYS, and then press ENTER.

4) Choose the "HR CONTROL MODE" using SPEED or INCLINE ARROW KEYS: * If SPEED ARROW KEY is pressed the console will display "SPEED HR CONTROL, SET MAX SPEED THEN PRESS ENTER" * If INCLINE ARROW KEY is pressed the console will display "INCLINE HR CONTROL, SET MAX INCLINE THEN PRESS ENTER"

5) Choose "TIME" using the NUMERIC KEYS, and then press ENTER.

6) Choose "WEIGHT" using the NUMERIC KEYS, and then press ENTER.

7) Press START.

16 17

JOHNSON COMMERCIAL TREADMILL

Page 11

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

• WORKOUT TIPS

The workout tips on the Johnson T7000 are listed below.

1) CAUTION! Before beginning any fitness program, have your physician give you a complete physical examination.

2) Begin working out, adapt the speed and incline level to meet your fitness goals.

3) Always attach the security clip to your clothing prior to working out.

4) Check that the unit is turned ON. The I/O switch is located at the front.

5) Answer setup prompts using the numeric keys or by pressing SPEED / INCLINE Ļ or ń keys.

6) Hold onto the handrail with one hand while you press SPEED Ļ with the other hand. Once you are comfortable with the walking or running speed, you can remove your hands from the handrail.

7) The better position of feet to walk on the treadmill is where feet planted on the belt to have your arms bent slightly and your hands grasped the heart rate sensors (as illustrated). At the running speed, the feet stand on the point of the belt where the hands at a natural swing are not able to touch the front handrail.

8) Do not attempt to grasp the sensors at speeds above 4.5 MPH, or 7.2 KPH. For these speeds, the use of a heart rate chest strap is recommended.

9) Always incorporate a cool-down period into your workout.

PART 6. MANAGER’s CUSTOM SETTING

The Manager’s Custom Setting allows the club owner to customize the treadmill for your club.

To enter the Manager’s Custom Setting, press and hold down the "INCLINEĻ" and "SPEEDĻ" keys. Continue to hold down the two keys until the MESSAGE CENTRE displays the words “MANAGER MENU”. Use the INCLINE arrow keys to scroll through the list of settings. The MESSAGE CENTRE will display, in turn, each of the custom settings. To select a displayed option, press the ENTER key. The Manager’s Custom Setting is listed on the following page. To change a setting, use the SPEED arrow keys or NUMERIC keys, and the press QUICK START. “SETTING SAVED” will appear in the message centre confirming that the message has been saved. To exit the setting setup without saving, press the RESET key within 5 seconds or the system will jump out of the setting automatically if no any key is inputted after 5 seconds.

Note:

Cool Down: Johnson Treadmill T7000 automatically initiates a 3-minute cool down once you complete a program. A prompt appears, indicating that you are in cool down.

JOHNSON COMMERCIAL TREADMILL

Page 12

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

•THE LIST OF MANAGER'S CUSTOM SETTING

CUSTOM SETTING DEFAULT MINIMUM MAXIMUM DESCRIPTION

MAXINUM TIME

DEFAULT TIME

DEFAULT LEVEL

DEFAULT WEIGHT

DEFAULT AGE

MAXINUM SPEED

MAXINUM

INCLINE

ACCUMULATED

DISTANCE

ACCUMULATED

TIME

START SPEED

LANGUAGE

P10

SOFTWARE

P11

VERSION

ENGLISH /

P12

METRIC UNITS

AUTO CHECK

P13

68kg / 150lbs

N/A

0.8kph /

0.5mph

ENGLISH

N/A

METRIC

N/A

34kg / 75lbs

0.8kph /

0.5mph

N/A

0.8kph /

0.5mph

N/A

159kg / 350lbs

20kph / 12mph

N/A

2.4kph /

1.5mph

N/A

This option enables fitness club managers to set the program maximum workout duration limits during peak and non-peak hours of club traffic. Active variable displayed in the TIME display after change.

This option controls the default program time.

This option controls the default program level.

This option controls the default weight used in the calorie calculations. Sets to default unit change (kilograms or pounds). Displayed in native units.

This option controls the default users age used in the target heart rate calculations.

Controls the maximum speed for all programs. Displayed in native units (miles per hour or kilometres per hour). Reverts to default value on unit change. Note: Minimum speed will follow the change of START SPEED.

This option changes the maximum incline grade to 4%, 8%, or 12%.

Accumulated distance is not editable, for display only. Displayed in native units (miles or kilometres). Holding the RESET key resets the accumulated distance.

Accumulated time is not editable, for display only. Holding the START key resets the accumulated time.

Controls the starting speed for all programs (minimum speed not affected). Displayed in native units (miles per hour or kilometres per hour). Reverts to default value on unit change.

The language of the MESSAGE CENTRE display.

Software version is not editable, for display only.

The measurement unit type for weight, distance, and speed.

The function is used to calibrate the treadmill’s speed and incline after the completion of the installation.

Part 7. MAINTENANCE

The T7000 is built for use in the light commercial environment - 8 hours a day and seven days a week. However, as a club manager or owner, you are responsible for cleaning and maintaining the unit’s integrity. If you fail to maintain the treadmill as described below, it could affect or void the Johnson limited warranty.

DANGER — To reduce the risk of electrical shock, always unplug the treadmill from its power source before cleaning it or performing any maintenance tasks.

NOTE: Safety of the equipment can be maintained only if the equipment is examined regularly

for damage or wear. Keep the equipment out of use until defective parts are repaired or replaced. Pay special attention to parts that are subject to wear, as outlined below.

• RECOMMENDED CLEANING TIPS

1) Use a soft, clean cotton cloth. DO NOT use paper towels to clean surfaces on the treadmill. DO NOT use ammonia or acid based cleaners. DO NOT use abrasive cleaners. DO NOT apply cleaners directly to equipment surfaces.

2) Wipe the console and side rails after every use.

3) Brush away any wax deposits from the deck and belt area. This is a common occurrence until the wax is worked into the belt material.

4) Be sure to remove any obstructions from the path of the elevation wheels including power cords.

5) Monthly, unplug the treadmill and remove the motor cover. Check for debris and clean with a dry cloth or small vacuum nozzle. DO NOT plug the unit in until the motor cover has been reinstalled.

• CENTERING THE BELT

Your Johnson Treadmill is built with a crowned roller to ensure proper tracking of the belt in the centre of the deck. When you run or walk, you may push off harder with one foot than the other. This uneven deflection can cause the belt to move off centre. Occasionally, the belt may need further adjustment to keep it centred. To centre the belt, use the enclosed 8mm Allen wrench to adjust the rear roller position. CAUTION! Please follow the centring belt procedure tips before you begin.

1) Do not wear loose clothing or loose jewellery while making this adjustment.

2) Never turn the bolts more than 1/4 turn at a time.

3) Tighten one side and loosen the other side to prevent from over-tightening or loosing the belt. Over-tightening the belt will significantly shorten the life of the belt.

4) To Press QUICK START and speed up the SPEED up to 6.4 kph / 4 mph during the belt adjustment.

5) After the belt adjustment, let the treadmill run for 5 minutes to test. If necessary, repeat the procedure until the belt is centred.

MANUFACTURING

P14

TEST

N/A

JOHNSON COMMERCIAL TREADMILL

N/A

The function is only for manufacturer use.

JOHNSON COMMERCIAL TREADMILL

Page 13

T7000 OWNER'S MANUAL T7000 OWNER'S MANUAL

If the belt moves to the left, turn the left tension bolt a 1/4 turn clockwise, and then turn

the right tension bolt - turn counter-clockwise to start the belt tracking back to centre of the

roller. If the belt moves to the right, turn the right tension bolt a 1/4 turn clockwise, and then turn the left tension bolt - turn counter-clockwise to start the belt tracking back to centre of roller.

Part 8. PRODUCT SPECIFICATIONS

Model Name

Foot Print

Box Dimensions

Max User Weight

Frame Construction

Motor Size

Elevation Range

Speed Range

Running Area

Johnson T7000

2210 x 880 mm / 87" x 35"

Console: 1070 x 879 x 300 mm / 42” x 35” x 12” Frame: 2210 x 879 x 364 mm / 87” x 35” x 14”

150 kg / 330 lbs

Heavy Gauge Steel

3.2 hp DC Continuous Duty

0 to 12%

0.8 to 20 kph / 0.5 to 12 mph

51 x 160 cm / 20" x 63"

Repeat these adjustments until the belt appears centred. Allow the belt to continue

running for several minutes to be sure that the tracking is stabilised.

NOTE: Do not exceed one full turn of the adjusting screws in either direction. If,

after one full turn, the belt does not track properly, contact your Johnson Dealer.

• TENSIONING THE BELT

Check the tension of the belt. The belt should be very snug. When a person walks

or runs on the belt it should not hesitate or slip. If this occurs, tighten the belt by

turning both tension bolts a -turn clockwise. Repeat if necessary, but NEVER TURN

the tension bolts over a 1/4 turn at a time. If, after tensioning the belt, the belt still

hesitates or slips, please contact your Johnson Dealer.

Roller

Deck

Belt Type

Cushioning System

Contact Heart Rate

Wireless Heart Rate

Programs

Console Feedback

Console Display

Direct Program Quick Keys

3" Crowned with Large O.D. Bearings

1" Low Maintance Prewaxed Phenolic Reversible

Habasit

8 Variable-Durometer Elastomer Cushions

Yes

Interval, Fat Burn, Weight Loss, 5K Run, Target HR, Manual, Quick Start

Distance, Calories, Calories per minute, Time, Speed, Incline, Level, Pace, Actual HR, Target HR

10 x 4 Dot Matrix Profile LED, 19-Character Alphanumeric Feedback

Yes

LED, Separate Heart Rate Display LED

CAUTION! Over-tightening the tension will severely shorten the life of the belt

and cause damage to other components.

JOHNSON COMMERCIAL TREADMILL

Numeric Quick Keys

Yes

JOHNSON COMMERCIAL TREADMILL