Johnson R, RHL, RL, TE, TEL Operator's Manual

...

Download

Page 1

2004

Operator's Guide

9.9/10/15 HORSEPOWER

R, RL, RH, RHL, TE, TEL

Page 2

Our First Words to the Owner/Operator

This Operator’s Guide is an essential part of your which, if followed, will provide you with a thorough understanding needed for proper operation, maintenance, care and above all safety!

The safety section of this Guide comes first because it is our first priority and it should be yours too. It is strongly recommended that you read this Guide from front cover to rear cover. Following this recommendation will assure the completeness of the information that is essential to your safety, the safety of any passengers and other boaters. An Operator’s Readiness Test has been prepared on the last page of this Guide.

Be safe! All passengers should be familiar with the proper operation of your boat and Be certain they fully understand and respect the controls and operation. Each operator is responsible for the safety of all passengers and other boaters. Please make safety your first priority and complete a boating safety course through your local Coast Guard, Power Squadron, Red Cross or State Boating Law Agency.

The pleasures of owning and operating a rewards for following our recommendations will be worthwhile. Remember that YOU are the key to safety. Good safety practices not only protect you but also protect the people around you.

Having fun is what it’s all about and, with your cooperation, the pertinent information in this Guide can ensure a safe and enjoyable experience.

Enjoy the great outdoors on the water...

Johnson

outboard can be significant. We strongly believe the

outboard. It contains pertinent information

Johnson

outboard.

WARNING

Be careful! Human error is caused by many factors: carelessness, fatigue, overload, preoccupation, unfamiliarity of operator with the product, drugs and alcohol to name a few. Damage to your boat and outboard can be fixed in a short period of time, but injury or death has a lasting effect.

For your safety and the safety of others, read this Guide from cover to cover and follow all safety warnings and recommendations. Do not disregard any of the safety precautions and instructions.

Anyone operating your boat should first read and understand this Guide before they operate your boat and motor.

The following trademarks are the property of Bombardier Motor Corporation of America or its affiliates:

2+4® fuel conditioner QuikStart™

Evinrude® S.L.O.W.™

Evinrude®/Johnson® anti-corrosion spray System Check®

Evinrude®/Johnson® Genuine Parts Triple-Guard® grease

Evinrude®/Johnson® XD25 Formula Touch-Trim

Hi-Vis® gearcase lubricant Twist-Grip

Johnson® Ultra-HPF™ gearcase lubricant

™

0 -

Page 3

Contents

GENERAL INFORMATION ................................................................................................... 2

SAFETY — THE RIGHT PLACE TO GET STARTED ................................................................................................ 2

PRODUCT REFERENCES, ILLUSTRATIONS AND SPECIFICATIONS ................................................................... 4

BOMBARDIER LIMITED WARRANTY FOR JOHNSON 2-STROKE OUTBOARD

ENGINES SOLD IN THE UNITED STATES AND CANADA .............................................................................. 5

BOMBARDIER LIMITED WARRANTY FOR JOHNSON 2-STROKE OUTBOARD

ENGINES SOLD OUTSIDE THE UNITED STATES AND CANADA .................................................................. 8

FEATURES ............................................................................................................................................................... 10

ENGINE SPECIFICATIONS ...................................................................................................................................... 12

EMERGENCY STOP SWITCH .................................................................................................................................. 13

FUEL AND OIL ................................................................................................................... 14

FUEL ......................................................................................................................................................................... 14

OIL ............................................................................................................................................................................. 15

ADDITIVES ................................................................................................................................................................ 15

FUEL/OIL RATIO ...................................................................................................................................................... 15

MIXING FUEL AND OIL ............................................................................................................................................ 15

FUEL SYSTEMS ....................................................................................................................................................... 16

BREAK-IN (10 HOURS) ............................................................................................................................................ 16

ENGINE STARTING ........................................................................................................... 17

BEFORE START-UP ................................................................................................................................................. 17

ENGINE STOPPING ................................................................................................................................................. 20

SHIFTING AND SPEED CONTROL ......................................................................................................................... 21

EMERGENCY STARTING ........................................................................................................................................ 21

FUEL ECONOMY ...................................................................................................................................................... 23

OPERATION ....................................................................................................................... 24

MOTOR ANGLE ADJUSTMENT .............................................................................................................................. 24

TRAILERING ............................................................................................................................................................. 24

TILTING AND TILT SUPPORT ................................................................................................................................. 24

SHALLOW-WATER DRIVE ...................................................................................................................................... 25

PROPELLER SELECTION ....................................................................................................................................... 26

MOORING ................................................................................................................................................................. 26

FLUSHING ................................................................................................................................................................ 27

ENGINE OVERHEATING .......................................................................................................................................... 28

IMPACT DAMAGE .................................................................................................................................................... 29

STORING .................................................................................................................................................................. 29

SPECIAL OPERATING CONDITIONS ..................................................................................................................... 30

MAINTENANCE .................................................................................................................. 31

10-HOUR INSPECTION ............................................................................................................................................ 31

OFF-SEASON STORAGE ........................................................................................................................................ 31

PRE-SEASON SERVICE .......................................................................................................................................... 32

BATTERY .................................................................................................................................................................. 33

ADJUSTMENTS ........................................................................................................................................................ 34

LUBRICATION .......................................................................................................................................................... 35

FUEL PUMP FILTER ................................................................................................................................................ 36

SPARK PLUGS ......................................................................................................................................................... 37

PROPELLER ............................................................................................................................................................. 37

ANTICORROSION ANODES .................................................................................................................................... 39

AC LIGHTING ........................................................................................................................................................... 40

TROUBLE CHECK CHART ...................................................................................................................................... 41

ENGINE MAINTENANCE AND INSPECTION SCHEDULE ..................................................................................... 42

INSTALLATION ........................................................................................................................................................ 46

Page 4

GENERAL INFORMATION

SAFETY — THE RIGHT PLACE TO GET STARTED

This Operator’s Guide contains essential information to help prevent personal injury and damage to equipment. It will acquaint the operator and passengers with the its controls, operation, maintenance and boating safety measures. Make sure all operators read, understand and follow the contents. This Guide should be kept in a waterproof bag with the product at all times during operation. If the product ownership is transferred, this Guide should be forwarded to the subsequent owners.

This Operator’s Guide uses the following signal words identifying important safety messages. These safety alert signal words mean:

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Evinrude/Johnson

outboard and

DANGER

Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, CAN result in severe injury or death.

A responsible, educated boater will fully appreciate the pleasures of boating and will be a safe boater. Boating Safety Classes are conducted by the U.S. Coast Guard Auxiliary, the U.S. Power Squadron and some Red Cross Chapters. For information about classes, call toll free 1-800-336-BOAT. For additional information about boating safety and regulations call: U.S. Coast Guard Boating Safety Hotline 1-800-368-5647. Outside North America please contact your DEALER or distributor for details about boating safety.

SAFETY MEASURES — General

To fully appreciate the pleasures, enjoyment and excitement of boating there are some basic rules that should be observed and followed by any boater. Some rules may be new to you and others may be common sense or obvious... irrespective, take them seriously! Failure to follow this safety information and safe boating rules could result in injury to you, your passengers or other water users.

Become completely familiar with the control and operation of your boat and motor before embarking on your first trip or taking on a passenger(s). If you have not had the opportunity to do so with your DEALER, practice driving in a suitable area and feel the response of each control. Be familiar with all controls before applying the throttle above idle speed. As the operator, you are in control and responsible for safe operation.

SAFETY MEASURES — Operation

Be sure at least one of your passengers knows how to handle your boat in case of an emergency.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate personal injury or property damage. It also may be used to alert against unsafe practices.

IMPORTANT: Identifies information that will help

prevent damage to machinery and appears next to information that controls correct assembly and operation of the product.

Although the mere reading of such information does not eliminate the hazard, the understanding and application of the information will promote the correct use of your outboard engine.

2 - General Information

All passengers should know the location of emergency equipment and how to use it.

All safety equipment and personal flotation devices must be in good condition and suitable for your type of boat. Always comply with the regulations that apply to your boat.

Contact with rotating propeller is likely to result in serious injury or death. Do not allow anyone near a propeller, even when the engine is off. Propeller blades can be sharp and can continue to turn even after the engine is shut off. Always shut off the engine when boat is near people in the water.

Page 5

Whenever running the engine, assure there is proper ventilation to avoid the accumulation of carbon monoxide (CO), which is odorless, colorless, and tasteless, and can lead to unconsciousness, brain damage, or death if inhaled in sufficient concentrations. CO accumulation can occur while docked, anchored, or underway, and in many confined areas such as the boat cabin, cockpit, swim platform, and heads. It can be worsened or caused by weather, mooring and operating conditions, and other boats. Avoid exhaust fumes from your engine or other boats, provide proper ventilation, shut off your engine when not needed, and be aware of the risk of backdrafting and conditions that create CO accumulation. In high concentrations, CO can be fatal within minutes. Lower concentrations are just as lethal over long periods of time.

Proceed with caution and at very low speed in shallow water. Grounding or abrupt stops may result in personal injury or property damage. Also be alert for debris and objects in the water.

Do not operate your boat if you are under the influence of drugs or alcohol.

High performance boats have a high powerto-weight ratio. If you are not experienced in the operation of a high performance boat, do not attempt to operate one at, or near, its top speed until you have gained that experience.

For more information, see your

Johnson

DEALER for a copy of Introduction

Evinrude/

to High Performance Boating, P/N 335763.

SAFETY MEASURES — Installation and Maintenance

Outboard Installation

The outboard must be correctly installed. Failure to correctly install the outboard could result in serious injury, death or property damage. We strongly recommend that your DEALER install your outboard to ensure proper installation.

Be familiar with the waters you are operating in. The gearcase of this outboard extends below the water surface and could potentially come in contact with underwater obstructions. Contact with underwater obstructions may result in loss of control and personal injury.

Avoid standing up or shifting weight suddenly in light weight boats.

Keep your passengers seated in seats. The boat’s bow, gunwale, transom and seat backs are not intended for use as seats.

Insist on the use of personal flotation devices, approved by the U.S. Coast Guard, by all passengers when boating conditions are hazardous, and by children and nonswimmers at all times.

Respect no wake zones, rights of other water users and the environment. As the "skipper" and owner of a boat you are responsible for damage to other boats caused by the wake of your boat. Allow no one to throw refuse overboard.

Know the marine traffic laws and obey them.

Do not overpower your boat by using an engine that exceeds the horsepower indicated on the boat’s capacity plate. Overpowering could result in loss of control. If your boat has no capacity plate, contact your DEALER or the boat’s manufacturer.

Maintenance

When replacement parts are required, use

Evinrude®/Johnson® Genuine Parts

with equivalent characteristics, including type, strength and material. Using substandard parts could result in injury or product malfunction.

Only perform service procedures which are detailed in this Operator’s Guide. Attempting to perform maintenance or repair on your outboard if you are not familiar with the correct service and safety procedure could cause personal injury or death. Further information can be obtained from your authorized

Johnson

DEALER. In many instances proper tools and training are required for certain service or repair procedures.

Maintain your boat and engine in top condition at all times. Adhere to the Engine Mainte- nance and Inspection Schedule.

or parts

Evinrude/

Remember, gasoline fumes are flammable and explosive. Always adhere to the fueling procedure contained in this Operator’s Guide and those given to you by the fueling station. Always verify fuel level before use and during the ride. Apply the principle of 1/3 fuel to destination, 1/3 back and 1/3 reserve fuel supply. Do not carry spare fuel or flammable liquids in any storage or engine compartments.

Operate your boat and outboard prudently and have fun. Do not forget that all persons must assist other boaters in case of emergency.

Prevent injury from contact with rotating propeller; remove propeller before flushing or before performing any maintenance.

General Information - 3

Page 6

PRODUCT REFERENCES, ILLUSTRATIONS AND SPECIFICATIONS

WARNING

When replacement parts are required, use

Evinrude/Johnson Genuine Parts

with equivalent characteristics, including type, strength and material. Using substandard parts could result in injury or product malfunction.

Bombardier Motor Corporation of America

the right to make changes at any time, without notice, to features, specifications and model availability. The right is also reserved to change any specification or part at any time without incurring any obligation to update older models. The information in the Guide is based on the latest specifications available at the time of publication.

Photographs and illustrations used in this Guide might not depict actual models or equipment but are intended as representative views for reference only. The continuing accuracy of this Guide cannot be guaranteed.

Certain features of systems discussed in this Guide might not be found on all models in all marketing areas.

Owner’s Identification

or parts

reserves

Stolen Outboards

North America — Report your outboard as stolen

to Customer and Dealer Support Services, 250 Sea Horse Drive, Waukegan, IL 60085 U.S.A. Give the outboard’s model and serial numbers and enclose a copy of the police report.

Outside North America — Report the theft to the

Bombardier

istered.

Technical Literature

Bombardier Motor Corporation of America

technical literature specifically for your outboard. A service manual, a parts catalog, or an extra Operator’s Guide can be purchased from your selling DEALER. For the name and location of the nearest

Evinrude/Johnson

and Canada log on to www.evinrude.com or

www.johnson.com.

Declaration of Conformity

Bombardier Motor Corporation of America

that the outboard to which this Operator’s Manual applies conforms to the essential requirements outlined in CE Machinery Directive 98-37-EC, as amended.

George Broughton Director of Outboards

distributor where the outboard was reg-

offers

DEALER in the United States

declares

North America — At the time of purchase, your DEALER will complete your outboard registration forms. Your portion provides proof of ownership and date of purchase.

Outside North America — See your DEALER or distributor for details.

Model and Serial Numbers

The model and serial numbers appear on a plate attached to the stern bracket or swivel bracket. Record your outboard’s:

Model Number ___________________________

Serial Number ____________________________

Purchase Date ___________________________

Ignition Key Number _______________________

4 - General Information

Page 7

BOMBARDIER LIMITED WARRANTY FOR

JOHNSON

2-STROKE OUTBOARD

ENGINES SOLD IN THE UNITED STATES AND CANADA

1. SCOPE OF THE LIMITED WARRANTY

Bombardier Motor Corporation of America* ("Bombardier") warrants its gines sold by authorized in material or workmanship for the period and under the conditions described below.

Johnson

dealers in the fifty United States and Canada ("Product") from defects

2. WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from the date of purchase by the first retail consumer or the date the Product is first put to use, whichever occurs first, for a period of:

TWENTY-FOUR (24) CONSECUTIVE MONTHS for private, recreational use; or

TWELVE (12) CONSECUTIVE MONTHS for commercial use. The Product is used commercially when it is used in connection with any work or employment that generates income, during any part of the warranty period. The Product is also used commercially when, at any point during the warranty period, it is installed on a boat that has commercial tags or is licensed for commercial use.

The repair or replacement of parts or the performance of service to Product under this warranty does not extend the life of this limited warranty beyond its original expiration date. All

Parts

and accessories installed by an authorized dealer at the time of sale, including but not limited to pro-

pellers, bear the standard Bombardier parts and accessories one-year limited warranty.

Johnson

® 2-stroke outboard en-

Evinrude®/Johnson Genuine

3. CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only on unused from a dealer authorized to distribute ("Dealer"), and then only after the Bombardier specified pre-delivery inspection process has been completed and documented by the purchaser and Dealer. Warranty coverage only becomes available upon proper registration of Product by Dealer or owner.

Only the original purchaser and any subsequent owners who reside in the United States and Canada and have purchased Product from a U.S. or Canadian Dealer are eligible for warranty registration and warranty coverage hereunder. Such limitations are necessary in order to allow Bombardier to protect the safety of its products, its consumers, and the general public.

As outlined in the Operator's Guide, timely routine required maintenance must be performed to maintain warranty coverage. Bombardier may require proof of proper maintenance prior to authorizing warranty coverage.

Johnson

2-stroke outboard engines purchased as new and

products in the country in which the sale occurred

4. WHAT TO DO TO OBTAIN WARRANTY COVERAGE

The registered owner must notify an authorized Dealer within two (2) days of the appearance of a defect. Owner must bring Product, including any defective part therein, to Dealer promptly after the appearance of the defect, and in any event, within the warranty period, and must provide Dealer with reasonable opportunity to repair the defect. The expenses of transporting Product to and from Dealer for warranty service are to be borne by the owner.

If the Product has not previously been registered, the owner may also be required to present proof of purchase to Dealer for warranty repairs. Owner is required to sign the repair/work order prior to the start of the repair in order to validate the warranty repair.

All parts replaced under this warranty become the property of Bombardier.

General Information - 5

Page 8

5. WHAT BOMBARDIER WILL DO

Bombardier's obligations under this warranty are limited to, at its sole discretion, repairing or replacing parts of Product found to be defective in material or workmanship, in the reasonable judgment of Bombardier. Such repair or replacement of parts will be done without charge for parts and labor, at any authorized Dealer. Bombardier's responsibility is limited to making the required repairs or replacements of parts with new or Bombardier-certified re-manufactured parts. No claim of breach of warranty shall be cause for cancellation or rescission of the sale of Product to owner.

In the event that warranty service is required outside of the fifty United States or Canada, owner will bear responsibility for any additional charges due to local practices and conditions, such as, but not limited to, freight, insurance, taxes, license fees, import duties, and any and all other financial charges, including those levied by governments, states, territories and their respective agencies.

Bombardier reserves the right to improve, modify or change Products from time to time without assuming any obligation to modify Products previously manufactured.

6. EXCLUSIONS – The following are not warranted under any circumstances:

• Replacement of parts due to normal wear and tear;

• Routine maintenance parts and services including but not limited to: maintenance requirements, engine and lower unit oil changes, lubrication, valve and linkage adjustments and replacement of fuses, zinc anodes, thermostats, timing belts, starter motor bushings, trim motor brushes, filters, propellers, propeller bushings and spark plugs;

• Damage caused by improper or lack of installation, maintenance, winterization and/or storage, failure to follow the procedures and recommendations in the Operator's Guide;

• Damage resulting from removal of parts, improper repairs, service, maintenance, or modification, or use of parts or accessories not manufactured or approved by Bombardier, which in its reasonable judgment, are either incompatible with Product or adversely affect its operation, performance, or durability, or resulting from repairs done by a person that is not an authorized Dealer;

• Damage caused by abuse, misuse, abnormal use, neglect, racing, improper operation or operation of the Product in a manner inconsistent with the recommended operation described in the Operator's Guide;

• Damage resulting from external damage, accident, submersion, water ingestion, fire, theft, vandalism or any act of God;

• Operation without proper fuel, oil or lubrication, or with fuels, oils or lubricants which are not suitable for use with the Product (see the Operator's Guide);

• Damage resulting from rust or corrosion;

• Damage caused from cooling system blockage by foreign material;

• Damage resulting from sand or debris in the water pump;

• Cosmetic or paint changes due to exposure to the elements.

This warranty will be voided in its entirety and rendered null and void where:

• Product has been altered or modified in such a way so as to adversely affect its operation, performance or durability, or change its intended use, horsepower or emission levels; or

• Product is or has been used for racing at any point, even by a prior owner.

6 - General Information

Page 9

7. LIMITATIONS OF LIABILITY

ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE LIFE OF THE EXPRESS LIMITED WARRANTY.

ALL INCIDENTAL, CONSEQUENTIAL, DIRECT, INDIRECT OR OTHER DAMAGES OF ANY KIND ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY INCLUDING, BUT NOT LIMITED TO:

expense for gasoline, expense for transporting Product to and from Dealer, removal of Product from a boat and reinstallation, mechanic's travel time, in-and-out of water charges, slip or dock fees, trailering or towing, storage, telephone, cell phone, fax or telegram charges, rental of a like or replacement Product or boat during warranty services or down time, taxi, travel, lodging, loss of or damage to personal property, inconvenience, cost of insurance coverage, loan payments, loss of time, loss of income, revenue or profits, or loss of enjoyment or use of Product.

SOME STATES, PROVINCES, OR JURISDICTIONS DO NOT ALLOW FOR THE DISCLAIMERS, LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR OTHER EXCLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE, OR PROVINCE TO PROVINCE.

No distributor, Dealer or any other person is authorized to make any affirmation, representation or warranty regarding Product other than those contained in this limited warranty and, if made, shall not be enforceable against Bombardier. Bombardier reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the Products sold while this warranty is in effect.

8. TRANSFER

If the ownership of Product is transferred during the warranty coverage period, this warranty shall also be transferred and be valid for the remaining coverage period provided that the former or new owner promptly contacts Bombardier or Dealer and gives the name and address of the new owner.

9. CONSUMER ASSISTANCE

• In the event of a controversy or dispute in connection with this Bombardier limited warranty, Bombardier recommends that you first try to resolve the issue at the dealership level by discussing the issue with Dealer's service manager or owner;

• If further assistance is required, please contact the Bombardier Customer Support Services, 250 Sea Horse Drive, Waukegan, IL 60085, 1-847-689-7090.

Revision April 2003 * Engines sold in Canada are distributed and serviced by Bombardier Inc.

General Information - 7

Page 10

BOMBARDIER LIMITED WARRANTY FOR

JOHNSON

2-STROKE OUTBOARD

ENGINES SOLD OUTSIDE THE UNITED STATES AND CANADA

For a copy of the Limited Warranty, see your Bombardier distributor/dealer authorized to distribute

Johnson

If further assistance is required, please contact Bombardier Customer Support Services, 250 Sea Horse Drive, Waukegan, Illinois, 60085, or the affiliate of Bombardier where the Product was registered for warranty.

2-stroke products in the country in which the sale occurs.

8 - General Information

Page 11

NOTES

General Information - 9

Page 12

FEATURES

Item Description Item Description

1 Water Pump Indicator 11 Emergency Restart Clip

2 Tilt/Run Lever 12 Emergency Stop Switch/Stop Button

3 Anticorrosion Anode 13 Shift Lever

4 Lubricant Drain/Fill Plug 14 Neutral Indicator

5 Lubricant Level Plug 15 Choke Knob

(1)

16 Starer Handle

6 Battery Cable

7 Clamp Screws 17 Manual Starter

8 Carrying Handle 18 Flushing Inlet Screw

9 Tilt Friction Nut 19 Fuel Tank

10 Start Button

(1) Electric Start Models

10 - General Information

Page 13

Item Description Item Description

20 Mounting Hardware 31 Water Intakes

21 Fuel Connector 32 Fish Line Trap

22 Steering Handle and

23 Idle Speed Adjustment 34 Antiventilation Plate

24 Retention Lug 35 Lift Grip

25 Model and Serial Number Plate 36 Engine Cover Latch

26 Steering Friction Adjustment Screw 37 Spark Plugs

27 Clip and Lanyard Assembly 38 Starter Motor

28 Angle Adjusting Rod 39 Fuel Pump Filter

29 Shallow-Water Drive Bracket 40 ECI Label

30 Positive Terminal Boot

(1) Electric Start Models

(2) Not supplied in all marketing areas

Twist-Grip

(1)

Throttle 33 Propeller

(2)

(1)

000288

General Information - 11

Page 14

ENGINE SPECIFICATIONS

9.9, 10, 15 Models

Displacement 15.6 cu. in. (256 cc)

Engine Type Two-Cycle, In-line, 2 Cylinder

Full Throttle Operating Range 9.9, 10 – 5000 to 6000 RPM

15 – 5500 to 6500 RPM

Power

Idle RPM in Gear

Ignition Timing – Idle

Exhaust Emission Control System per SAE J1930

Fuel Requirements

Fuel/Oil Ratio 50:1

Starting R, RL, RH, RHL – Rope start

Battery, Minimum 360 CCA (465 MCA)

Spark Plug Extended Low Speed Operation Torque

AC Lighting

(1)

(2)

(3)

(2)

W.O.T.

(2)

9.9 – 9.9 HP (7.4 kw) @ 5500 RPM 10 – 10 HP (7.5 kw) @ 5500 RPM 15 – 15 HP (11.2 kw) @ 6000 RPM

700 ± 50

Not Adjustable Not Adjustable

EM (Engine Modification)

87 Pump Posted AKI (89 RON) – Refer to Fuel and Oil

OR 50 ampere-hour, 12 volts

Refer to ECI Label

9.9 only – QL86C @ 0.030 in. (0.8 mm) Gap 18 to 21 ft. lbs. (24 to 28 N

60 watts AC @ 12 volts

·m)

Gearcase –Lubricant

Capacity

Propeller

(4)

Evinrude/Johnson Ultra-HPF™

gearcase lubricant

9 fl. oz. (260 ml)

9.9 – 9 1/2 x 10 in. (24.1 x 25.4 cm) 10, 15 – 9 x 11 in. (22.9 x 27.9 cm)

Fuel Tank – Capacity 9.9 – 3.2 U.S. Gallons (12.1 Liters)

10, 15 – 6 U.S. Gallons (22.7 Liters)

Weight R, RH – 74 lbs. (33.6 kg)

RL, RHL – 77 lbs. (34.9 kg)

Transom Height R, RH – 14 1/2 to 15 in. (36.8 to 38.1 cm)

RL, RHL – 19 1/2 to 20 in. (49.5 to 50.8 cm)

Sound at Driver’s Ear

) ICOMIA 39.94

Vibration at Tiller (arms) Less than 2.5 m/s

(1) Rated following the standards of ICOMIA 28.83, ISO 3046, and NMMA.

(2) Emission Control Information

(3) Available as optional kit

(4) Not supplied in all marketing areas

86.0 dB(A)

12 - General Information

Page 15

EMERGENCY STOP SWITCH

If equipped, the emergency stop switch is on the steering handle. Use of the emergency stop feature is highly recommended on all boats.

Connect the clip to the emergency stop switch. Snap the lanyard to a secure place on the operator’s clothing or life vest — not where it might tear away instead of activating the stop switch. Disconnecting the clip and lanyard will stop the engine and prevent the boat from becoming a runaway if the driver moves beyond the range of the lanyard. If the lanyard is too long, it can be shortened by knotting or looping it. DO NOT cut or retie the lanyard.

An extra clip is provided — another person can insert it in the stop switch and start the motor in an emergency.

1. Emergency stop switch

2. Clip

1. Extra clip

WARNING

Avoid knocking or pulling the clip off the stop switch during normal boating. The resulting unexpected loss of forward motion can throw occupants forward, causing injury.

Your emergency stop switch can be effective only when in good working condition. At each outing, inspect clip and lanyard for cuts, breaks, or wear. Replace worn or damaged parts.

Keep the lanyard free from obstructions and entanglements.

At each outing, test the system’s operation. With the engine running, remove the clip from the switch by pulling the lanyard. If the engine does not stop running, see your DEALER.

General Information - 13

Page 16

FUEL AND OIL

FUEL

WARNING

Gasoline is extremely flammable and highly explosive under certain conditions. Follow the instructions in this section explicitly. Improper handling of fuel could result in property damage, serious injury, or death.

Always turn off the engine before fueling.

Never permit anyone other than an adult to refill the fuel tank.

Do not fill the fuel tank all the way to the top, or fuel may overflow when it expands due to heating by the sun.

Remove portable fuel tanks from the boat before fueling.

Always wipe off any fuel spillage.

Do not smoke, or allow open flames or sparks, or use electrical devices such as cellular phones in the vicinity of a fuel leak or while fueling.

Always work in a well-ventilated area.

Your outboard is certified to operate on unleaded automotive gasoline with an octane rating equal to or higher than that specified in Minimum Octane chart. When using gasoline that contains MTBE or alcohol, follow these guidelines:

Using unleaded gasoline that contains methyl tertiary butyl ether (MTBE) is acceptable ONLY if the MTBE content does not exceed 15% by volume.

Using alcohol-extended fuels is acceptable ONLY if the alcohol content does not exceed:

• 10% ethanol by volume; or

• 5% methanol with 5% cosolvents by volume

Minimum Octane

Inside the U.S. 87 (R+M)/2 AKI

Outside the U.S. 89 RON

Your outboard has been designed to operate using the above fuels; however, be aware of the following:

The boat’s fuel system may have different requirements regarding the use of alcohol fuels. Refer to the boat’s Owner Guide.

Alcohol attracts and holds moisture that can cause corrosion of metallic parts in the fuel system.

Alcohol blended fuel can cause engine performance problems.

IMPORTANT: Always use fresh gasoline. Gasoline will oxidize and weather; the result is loss of octane, volatile compounds, and the production of gum and varnish deposits which can damage the outboard.

WARNING

Leaking fuel is a fire and explosion hazard. All parts in the fuel system should be inspected frequently and replaced if signs of deterioration or leakage are found. Inspect the fuel system each time you refuel, each time you remove the engine cover, and annually.

14 - Fuel and Oil

Page 17

OIL

MIXING FUEL AND OIL

Evinrude/Johnson

is recommended for your outboard. It contains a

richer additive package than other TC-W3 oils, minimizing carbon build-up and deposits on pistons and bearing surfaces. It provides 25% greater detergency than minimum TC-W3 requirements.

Evinrude/Johnson

best engine performance while controlling piston and combustion chamber deposits, providing superior lubrication and ensuring maximum spark plug life.

Evinrude/Johnson

not available, you must use an NMMA-certified TCW3 oil such as

Evinrude

IMPORTANT: Failure to follow this recommendation could void the engine warranty if a lubricationrelated failure occurs.

biodegradable outboard oil.

XD25 Formula outboard oil

brand oils are formulated to give

XD25 Formula outboard oil is

Evinrude/Johnson

direct injection oil

ADDITIVES

IMPORTANT: Only use fuel additives approved by

Bombardier

ditives can result in poor performance or engine damage.

Evinrude/Johnson 2+4

prevent gum and varnish deposits from forming in fuel system components and will remove moisture from the fuel system. It can be used continuously and should be used during any period when your engine is not being operated on a regular basis. Its use will reduce spark plug fouling, fuel system icing, and fuel system component deterioration.

for your outboard. Use of other fuel ad-

fuel conditioner will help

FUEL/OIL RATIO

Use the following chart and these guidelines to mix oil with the engine’s fuel.

Fuel

Ratio

50:1 16 fl. oz. oil 8 fl. oz. oil 20 ml oil 25:1 32 fl. oz. oil 16 fl. oz. oil 40 ml oil

Portable Tank

Above and below 32° F (0°C), add one gallon of fuel. Pour in required amount of oil. Add remaining fuel. Install filler cap and tip tank gently to distribute oil.

Permanently Installed Tank

Above 32° F (0° C), pour oil slowly with the fuel as tank is filled. Below 32° F (0° C), add one gallon of fuel to a separate container. Pour in required amount of oil. Install filler cap and tip container gently to distribute oil. Slowly pour oil/fuel mixture into tank with fuel as tank is filled.

6 U.S. Gallons 3 U.S. Gallons 1 Liter

New Engine

During break-in, you must use a 25:1 (4% oil) fuel/ oil ratio in your fuel tank. Refer to Break-In (10

Hours). Normal Operation

After break-in, the engine must be operated at a

50:1 (2% oil) fuel/oil ratio. High Performance

During high performance operation you must use a 25:1 (4% oil) fuel/oil ratio in your fuel tank.

Fuel and Oil - 15

Page 18

FUEL SYSTEMS

WARNING

If your motor is equipped with a quick-disconnect fuel hose, disconnect the fuel hose from the motor and from the fuel tank when the motor is not being used for a period of time. Disconnecting the hose will avert fuel leaks in the hose or at the engine.

IMPORTANT: Fuel distribution hoses in the boat

must deliver fuel at the rate of flow needed by the engine. Minimum inside diameter of fuel hoses must be 5/16 in. (8 mm).

Fuel systems with built-in tanks, particularly those that include antisiphon valves and filter/primer units, may have restrictions that will not allow the engine fuel pump to deliver sufficient fuel under all conditions. This can result in a loss of performance and possible engine damage. If a performance problem exists, see your DEALER.

To avoid difficulty when restarting, never run the engine with the fuel hose disconnected or run the engine out of fuel.

BREAK-IN (10 HOURS)

IMPORTANT: Follow this procedure to protect your

new outboard during its initial hours of operation. Careful break-in allows internal engine components to “seat” properly, resulting in maximum engine performance.

Failure to carefully follow the break-in procedures can result in engine damage.

During break-in, you must use extra oil. The fuel/oil ratio for the first 10 hours of operation must be 25:1 (4% oil). The fuel/oil ratio during normal operation, after break-in, must be 50:1 (2% oil).

Perform the 10-Hour break-in procedure with the boat and engine in the water, using an appropriate propeller.

DO NOT perform break-in using a flushing device. DO NOT start-up or run the engine out of the water. DO NOT leave a running engine unattended.

IMPORTANT: Before the first start-up of your new engine:

• Read Engine Starting, Engine Stopping, and Shifting and Speed Control.

• Check the gearcase lube level. Refer to Lubrication.

• Perform prelaunch checks of all equipment.

Launch the boat and start the engine according to the procedures in Engine Starting.

• Verify water pump operation often. Look for a steady stream of water from the water pump indicator. If the stream of water stops, shut off the engine to prevent damage. Find and correct the cause, or see your DEALER before you continue.

• Verify shift function by shifting into gear and observing that the boat moves and that the movement is in the same direction as the shifter. Refer to Shifting and Speed Control.

• Change the RPM often. Avoid holding a throttle setting longer than 15 minutes.

1. First 10 Minutes of Operation — Operate the

engine in gear at fast idle only.

2. Next 50 Minutes — Operate engine in gear at various speeds no faster than 3500 RPM.

DO NOT hold a constant throttle setting. Change engine speed every 15 minutes.

With easy planing boats, use full throttle to quickly accelerate boat onto plane. Immediately reduce throttle to one-half as soon as boat is on plane. BE SURE boat remains on plane at this throttle setting.

3. Second Hour — Use full throttle to accelerate boat onto plane, then reduce throttle setting to three-quarters. BE SURE boat remains on plane at this throttle setting.

At intervals, apply full throttle for periods of one to two minutes, returning to three-quarters throttle for a cooling period.

Change engine speed every 15 minutes.

4. Next Eight Hours — Avoid continuous full throttle operation for extended periods.

Change engine speed every 15 minutes. DO NOT exceed recommended maximum engine

RPM. Refer to Engine Specifications.

16 - Fuel and Oil

Page 19

ENGINE STARTING

DANGER

DO NOT run the engine indoors or without adequate ventilation or permit exhaust fumes to accumulate in confined areas. Engine exhaust contains carbon monoxide which, if inhaled, can cause serious brain damage or death.

WARNING

Move tilt/run lever to RUN. Be sure the engine is in normal operating position. Refer to Tilting and Tilt

Support.

The engine cover is a machinery guard. DO NOT operate your outboard with the cover off unless you are performing maintenance, and then be careful to keep hands, hair, and clothing clear of all moving parts. Contact with moving parts could cause injury.

DANGER

Contact with a rotating propeller is likely to result in serious injury or death. Assure the engine and prop area is clear of people and objects before starting engine or operating boat. Do not allow anyone near a propeller, even when the engine is off. Blades can be sharp and the propeller can continue to turn even after the engine is off. Always shut off the engine when near people in the water.

BEFORE START-UP

Review and follow Break-In (10 Hours) if the engine is new.

You MUST supply water to the engine before attempting to start it. Engine damage can occur quickly. Refer to Engine Overheating or Flushing.

1. RUN position

If you will be using a battery, connect it as instructed in Battery.

Electric start models can be started manually and operated without a battery.

WARNING

When not connected to a battery, cover the positive (+) battery cable’s ring terminal with the attached boot to prevent the charging system from sparking.

Do not wrap the loose battery cable around the engine as a way of storing it. Doing so can restrict steering or damage the cable, or both. Loop the cable and hang it close to the engine.

Do not connect electrical equipment to the engine’s charging system. The connected equipment and the engine could both be damaged.

1. Positive (+) battery cable boot

Engine Starting - 17

Page 20

Connect the fuel hose to the fuel connector.

If equipped, attach the clip and lanyard assembly to the emergency stop switch. Snap the lanyard to se-

cure place on your clothing or life vest.

1. Fuel hose connector

2. Fuel connector

If equipped, open vent screw on fuel tank’s filler cap.

Squeeze fuel primer bulb, outlet end up, until firm.

1. Fuel tank operable vent

2. Fuel primer bulb

1. Emergency stop switch

Twist the throttle to SHIFT or slower.

1. SHIFT

Move the shift lever to NEUTRAL. Refer to Shifting and Speed Control.

18 - Engine Starting

WARNING

Always shift to NEUTRAL before starting the engine to prevent sudden boat movement, which can cause injury.

Page 21

Twist the throttle grip to START.

1. START

Rope Start

While seated, grasp the starter handle and pull slowly until starter engages, then pull hard. Repeat, if needed, until motor starts. To prevent damage to starter assembly, allow starter cord to rewind before releasing starter handle. If motor does not start, refer to Trouble Check Chart.

IMPORTANT: Avoid engine damage. DO NOT run

engine above START in NEUTRAL.

Start-up (Cold Engine)

WARNING

Start engine with shift lever in NEUTRAL. Attempting to manually start the engine while in gear may damage parts or cause the start-in-neutral-only feature to become inoperative.

Starting a cold engine normally requires use of the engine choke. Pull the choke knob all the way out.

1. Starter handle

2. NEUTRAL

Electric Start

While seated, press start button to START motor.

1. START button

2. NEUTRAL

1. Choke knob

Release start button as soon as engine starts. If engine does not start, release button momentarily and then try again.

Engine Starting - 19

Page 22

IMPORTANT: Starter motor can be damaged if operated continuously for more than 10 seconds. DO NOT press start button to START position when engine is running. Starter and flywheel will be damaged.

All Models

Push choke knob in gradually when motor is sufficiently warmed up.

IMPORTANT: If your outboard does not react normally to this starting procedure or fails to start, refer to Trouble Check Chart.

After Engine Starts

Check the water pump indicator. A steady stream of water indicates the water pump is working. If a steady stream of water from the water pump indicator is not visible, stop the engine. Refer to Engine

Overheating.

ENGINE STOPPING

Twist the throttle grip to SHIFT position or slower. Move shift lever to NEUTRAL. Press the STOP button until the engine stops run-

ning. If equipped, close the vent screw on the fuel tank’s filler cap.

1. STOP button

To avoid difficulty when restarting, never stop the engine by running it with the fuel hose disconnected or otherwise running it out of fuel.

IMPORTANT: To avoid engine damage, after startup, do not exceed one-quarter throttle (less than 2000 RPM) in NEUTRAL for extended periods of time.

Start-up (Warm Engine)

Follow Cold Engine procedure except warm engines do not normally require use of the choke. If engine fails to start, use the choke.

20 - Engine Starting

Page 23

SHIFTING AND SPEED CONTROL

IMPORTANT: Carefully check the function of all

control and engine systems before leaving the dock. DO NOT shift the engine into FORWARD or REVERSE while it is shut OFF.

Shifting

With the engine running, twist the throttle grip to SHIFT or slower.

Move the shift lever briskly and decisively to FORWARD or REVERSE.

1. Shift lever

2. FORWARD

3. REVERSE

1. Decrease speed

2. Increase speed

EMERGENCY STARTING

If the starter cord breaks or the starter fails, your engine can be started using a piece of the starter cord or a 9/64 in (6 mm) cord about 4 ft. (1.2 m) long.

WARNING

When using Emergency Starting procedures, the start-in-neutral-only feature is inoperative. Make sure shift lever is in NEUTRAL position to prevent injuries from unexpected boat movement when the engine starts.

WARNING

Do not operate motor in REVERSE with the tilt/run lever in TILT. Motor may tilt out of the water, resulting in loss of control.

IMPORTANT: Before moving the shift lever, reduce

throttle to SHIFT speed or slower, then pause until motor slows to idle speed and boat has slowed.

Speed Control

With the engine running, twist the throttle grip:

• Counterclockwise to increase speed; or

• Clockwise to decrease speed.

The engine cover is a machinery guard. To prevent injury from moving engine components, keep hands, clothes, and hair clear of powerhead.

Prevent electric shock by keeping clear of the ignition coils and spark plug leads when the motor is being started or is running. Shock can cause serious personal injury under certain conditions.

DO NOT turn flywheel by hand. Use starter cord only.

Engine Starting - 21

Page 24

Move tilt/run lever to RUN position. Place motor in its normal operating position.

1. RUN position

Be sure:

• Engine is in normal operating position.

• Fuel hose primer bulb is firm.

• Shift lever is in NEUTRAL.

•

Twist-Grip

throttle is at START.

Electric Start Models

WARNING

DO NOT use jumper cables and a booster battery to start engine. Do not charge a battery in the boat with an external charger. Fumes vented during either operation can lead to an explosion.

Follow the procedures in Manual Start Models.

Manual Start Models

Remove three screws that secure the manual starter.

Pull latch and remove engine cover.

1. Screws

22 - Engine Starting

Page 25

Tip the manual starter housing to remove the starter lockout link. Secure the lockout link in the lower engine cover, away from moving engine parts.

1. Starter lockout link

Tie a knot in one end of your emergency starter cord and hook it in the notch on the flywheel. Wind the cord clockwise around the starter ridge on the flywheel.

All Models

Follow the starting procedures in Start-up (Cold Engine).

While seated, pull hard on emergency starting cord to start motor. After the motor starts, run it at less than 2000 RPM in NEUTRAL for two minutes, then reduce speed to an idle.

Do not attempt to replace manual starter or engine cover while engine is running. If equipped, snap emergency stop switch lanyard to a secure place on your clothing.

Proceed to nearest landing for service.

FUEL ECONOMY

The economy throttle position can save fuel, depending on boat load and hull design. When boat reaches top speed, throttle back from FULL SPEED. You will save fuel without a noticeable loss of speed.

1. Knot

2. NEUTRAL

Engine Starting - 23

Page 26

DANGER

OPERATION

TRAILERING

DANGER

MOTOR ANGLE ADJUSTMENT

Motor should be perpendicular to the water when the boat is underway at full speed. This adjustment can only be determined by water testing the boat. Set angle adjustment for your normal load.

Place motor in full tilt position. Refer to Tilting and Tilt Support.

• Move angle adjusting rod.

Trailer your boat with the motor in a vertical position. If your trailer does not provide adequate road clearance, the motor can be trailered by using an accessory trailering bracket.

IMPORTANT: Whenever using an accessory trailering bracket, the motor must be restrained. Bouncing during transport will damage the motor and boat’s transom. DO NOT use the motor’s tilt support or the shallow-water drive bracket as a trailering bracket.

TILTING AND TILT SUPPORT

WARNING

Your motor has “impact protection” and “reverse lock” only when the tilt/run lever is in RUN position. If operated with the tilt/run lever left in TILT position, the motor could tilt into the boat suddenly, causing loss of control or serious injury.

IMPORTANT: Use the tilt grip to tilt your motor; not

the steering handle.

24 - Operation

Page 27

Tilt UP

Move tilt/run lever to TILT position.

Tilt DOWN

Move tilt/run lever to RUN position.

1. Tilt/run lever – TILT position

Grasp tilt grip on engine cover and tilt motor to the full tilt position.

Tilt support will automatically engage.

1. Tilt grip

WARNING

While engine is tilted, leave tilt lever in the TILT position. When the tilt/run lever is in the RUN position, tilt support can release unexpectedly and allow motor to drop.

1. Tilt/run lever – RUN position

Grasp tilt grip on engine cover and raise motor slightly.

Tilt support will automatically disengage. Slowly lower motor to its normal operating position.

SHALLOW-WATER DRIVE

WARNING

When in shallow-water drive, your motor has no protection from the effects of underwater impact.

Operate your motor in FORWARD and ONLY at slow speed. The motor can tilt up forcibly and drop suddenly if it hits an underwater object or if you shift to REVERSE and apply throttle. You could lose control.

The motor’s depth in shallow-water drive is controlled by the position of the motor angle adjusting rod. Relocate the motor angle adjusting rod if necessary. Refer to Motor Angle Adjustment.

Slow the engine and shift to NEUTRAL before engaging or disengaging shallow-water drive.

Operation - 25

Page 28

Engage

Move tilt/run lever to the TILT position.

Disengage

Move tilt/run lever to the RUN position.

1. Tilt/run lever – TILT position

2. NEUTRAL

Grasp tilt grip on engine cover and tilt motor halfway.

Shallow-water drive bracket will automatically engage.

Slowly, lower motor until shallow-water drive brackets rests against angle adjusting rod.

IMPORTANT: Check often that water intakes are completely submerged and the water pump indicator is discharging a steady stream of water.

1. Tilt/run lever – RUN position

2. NEUTRAL

Grasp tilt grip on engine cover and tilt motor slightly. Shallow-water drive bracket will automatically re-

lease. Slowly, lower motor to normal operating position.

PROPELLER SELECTION

To select the correct propeller for your boating application, your boat and motor MUST be water tested. See your DEALER for assistance.

Refer to Propeller, before removing or installing

propeller.

IMPORTANT: The correct propeller for your boat, under normal load conditions, will allow the engine to run near the midpoint of the RPM operating range at full throttle. Refer to Engine Specifica-

tions.

MOORING

You may moor your boat with the motor’s gearcase out of the water by using its tilt feature. Refer to Tilt- ing and Tilt Support.

26 - Operation

Page 29

FLUSHING

DANGER

4) Start the water — keep pressure between 20

to 40 psi (140 to 300 kPa).

Flush your engine with fresh water as soon as possible after each use in salty, polluted, or brackish water to minimize the formation of deposits that can clog cooling passages. Flush the engine on the trailer or at dockside while it is:

Tilted or vertical, running or stopped.

Outboard — Running

WARNING

Prevent injury from contact with rotating propeller; remove the propeller before flushing.

1) Place the engine in vertical position in a well-

ventilated area with good drainage.

2) Remove the plug from the flushing port.

1. Flushing device

5) Start the engine — run it at idle only and flush it for at least five minutes.

6) Shut OFF the engine, remove the flusher (if used), and install the plug. If the plug is also the water pump indicator, turn it so the water streams out to the side, where it can be seen easily from the helm.

7) Leave the outboard in vertical position long enough to completely drain the powerhead.

Outboard Not Running

1) The outboard may be in a tilted or vertical posi-

tion.

2) Remove the plug from the flushing port.

3) Install flushing device (if needed) and garden

hose.

4) Start the water and flush the engine for at least five minutes — keep pressure between 20 to 40 psi (140 to 300 kPa).

5) Remove the flusher (if used); install the plug. If the plug is also the water pump indicator, turn it so the water streams out to the side, where it can be seen easily from the helm.

6) Lower the outboard to vertical position long enough to completely drain the powerhead.

1. Plug

2) Install flushing device (if needed) and garden hose.

3) Place the remote control lever in NEUTRAL with the propeller removed.

Operation - 27

Page 30

ENGINE OVERHEATING

IMPORTANT: Do not run your engine — even for a

brief start-up — without supplying water to it. Refer to Flushing.

While boating, the engine’s water intakes must stay completely submerged and unobstructed. Observe proper transom height and trim angle. While the engine is running, the engine’s water pump indicator must discharge a steady stream of water. Check the indicator often, especially when operating in weeds, muddy and debris-laden water, and at extreme trim angles.

If the stream of water from the water pump indicator becomes intermittent or stops, reduce speed to idle and:

• Shift to NEUTRAL;

• SHUT OFF the engine;

• Raise the engine;

• Clean the water intakes and the water pump indicator; and

• Restart engine and run at idle.

If cleaning the screens and indicator does not restore the water pump indicator’s steady discharge, SHUT OFF the motor and do not attempt to operate it. See your DEALER.

If you succeed in restoring the water pump indicator’s steady discharge, continue to IDLE the engine until it cools.

After an engine overheat, have your DEALER torque the cylinder head and exhaust cover screws and DETERMINE THE CAUSE OF THE OVERHEAT.

1. Water intake screens

2. Water pump indicator

28 - Operation

Page 31

IMPACT DAMAGE

Your engine can be damaged from impact with underwater objects. Such impacts can result in serious damage to your engine and injury to boat occupants from the engine or its parts entering the boat. Occupants can also be ejected or injured by falling against portions of the boat as a result of rapid deceleration following impacts. When boating in unfamiliar, shallow, or debris-laden waters, seek information on safe boating areas and navigation hazards from a reliable local source. Reduce your speed and keep a sharp lookout!

If you hit any object, stop immediately and examine the engine for loosening of attaching hardware and clamp screws, if equipped. Inspect for damage to swivel and stern brackets, steering components, and components in the area of impact. Also, examine the boat for structural damage. Tighten any loosened hardware. If the collision occurred in the water, proceed slowly to harbor. Before boating again, have your DEALER thoroughly inspect all components.

WARNING

Failure to inspect for damage could result in sudden, unexpected component failure, loss of boat control, and personal injury. Unrepaired damage could reduce your boat and engine’s ability to resist future impacts.

STORING

To avoid difficulty when restarting, never run the engine with the fuel hose disconnected or run the engine out of fuel.

If you must tilt the motor to remove it from the water, lower it and allow the cooling system to drain completely as soon as you clear the launch area.

Between uses, store your motor in a vertical position.

For recommendations on extended periods of storage, refer to Off-Season Storage.

Operation - 29

Page 32

SPECIAL OPERATING CONDITIONS

Salt Water

Flush the engine internally after use in salt, polluted, or brackish water to help prevent mineral deposits from clogging cooling passages. Refer to Flushing.

During use in salt or brackish water, additional anodic protection for the boat and outboard may be required.

During long periods of mooring, tilt the gearcase out of the water — except in freezing temperatures. Upon removal from salt water, leave it in a vertical position until its cooling system has drained.

Weedy Water

Weeds block water intakes and cause your outboard to overheat. Weeds on the propeller create vibration and reduce boat speed.

Run at slow speeds and in REVERSE frequently to clear weeds from the propeller and water intakes. Check the water pump indicator often.

If REVERSE operation does not clear away weeds, SHUT OFF the engine. Remove weeds from propeller area and water intakes before operating at higher speed.

Boat Bottom and Engine External Finish

The condition of your boat’s bottom affects performance. A covering of marine growth reduces speed. For maximum performance, keep the boat’s running surface clean by wiping it dry after each use and washing it occasionally.

After operating your outboard, rinse it with fresh water and wipe it dry. Apply Corrosion Spray to any surface subject to corrosion, but avoid the anticorrosion anode(s).

Periodically, wash the entire boat and outboard with soapy water and apply a coat of automotive wax. Leave the engine cover in place when washing the outboard.

Evinrude/Johnson

Anti-

High Altitude

If you boat at altitudes above 3000 ft. (900 m), your engine might benefit from a lower pitched propeller, different carburetor calibration, or both. See your DEALER.

IMPORTANT: To avoid permanent powerhead damage, be sure that an engine modified for high altitude operation is properly identified and returned to original calibration and propeller size if operated below 3000 ft. (900 m).

Shallow Water

IMPORTANT: Serious engine damage will occur if

the gearcase is allowed to drag on the waterway bottom.

Freezing Weather

DURING operation in freezing weather, keep the gearcase submerged at all times.

Upon removing your motor from the water, leave it in a vertical position until its cooling system is drained.

IMPORTANT: Water that has leaked into the gearcase, or remained in the cooling system or other components can freeze, causing serious engine damage.

Submerged Engine

If your engine has been under water, have it serviced immediately upon recovery. If immediate

service is unavailable, resubmerge it in fresh water to avoid prolonged exposure to the atmosphere.

After submersion, all boat and engine electrical, fuel, and oiling systems must be inspected for signs of water intrusion. Your DEALER should perform this service.

Under Tow

Should you require a tow from another boat:

• Shift your engine to NEUTRAL;

• Tilt its gearcase out of the water; and

• Off-load all persons into another boat.

30 - Operation

Keep towing speed slower than planing speed.

Auxiliary Engine

When your auxiliary engine is shut OFF, shift it to NEUTRAL and keep its gearcase out of the water by tilting it fully or raising the mounting bracket.

Page 33

MAINTENANCE

Maintenance, replacement, or repair of the emission control devices and systems may be performed by any marine SI (spark ignition) engine repair establishments or individual.

Tampering with the carburetor to change horsepower or modify emission levels beyond factory settings or specifications will void the product warranty.

WARNING

10-HOUR INSPECTION

After 10 hours of operation, your new engine will be broken in and its mechanical parts will have seated. At that time, all systems should be checked and any adjustments needed should be made.

Your DEALER will perform this 10-Hour Inspection at your request and expense (based on local rates), according to what your engine needs — refer to En-

gine Maintenance and Inspection Schedule, 10- Hour Inspection for a partial list.

Follow consistent preventive maintenance by having your DEALER check and service your engine once a year or after each 100 hours of operation, whichever comes first.

OFF-SEASON STORAGE

To do the off-season storage preparations yourself, gather the supplies and perform the following steps.

2+4

fuel conditioner

Triple-Guard Ultra-HPF Storage Fogging Oil

Stabilize the engine’s fuel supply with ditioner during the last hours of operation to ensure proper stabilization, following instructions on the

container for mixture. Be sure to run the engine long enough for the treated fuel to reach the engine.

grease

gearcase lubricant

spray can

2+4

fuel con-

WARNING

Prevent injury from moving engine components. Before starting the engine:

Shift it to NEUTRAL.

Keep hands, clothes, and hair clear of powerhead.

Remove the propeller if you use a flushing device.

IMPORTANT: Provide water supply to the engine

and start it. Run the engine at idle only. To run the engine on a flusher, refer to Flushing.

Storage Fogging Oil —

the can, fog the engine.

Ignition, oil, and fuel systems — Check for misplaced leads and damaged or deteriorated parts. Be sure starter solenoid terminal boot and all connectors are in place.

Fuel filter — Clean.

Following instructions on

You must protect against natural environmental conditions that can be damaging to an outboard motor. Temperature and humidity changes while your outboard motor is not in use can cause corrosion of internal engine parts when they are not protected. Fuel remaining in your fuel tank and in the engine will oxidize and weather which can result in loss of octane and can cause gum deposits in the fuel system. Your warranty does not cover engine failure caused by these conditions. We strongly recommend that you have your DEALER prepare your outboard for the off-season.

Screws, bolts, nuts — Tighten any that are loose.

Propeller — Remove and examine. If damaged, see your DEALER. Clean the propeller shaft and lubricate it. Refer to Propeller.

Lubrication — Refer to Lubrication to drain and refill the gearcase and for lubricating points on the engine.

Touch up painted surfaces and wax the engine’s exterior. Store the engine on the boat (or an engine stand) in a vertical, self-draining position.

Maintenance - 31

Page 34

IMPORTANT: Never place the gearcase higher than the powerhead. Any water remaining in the exhaust passages can run into the cylinders and cause serious damage.

If you remove an "installed" engine, examine all hardware you loosened or removed from the engine and its steering, throttle, and shift systems. Replace damaged or missing parts with

Johnson Genuine Parts

Battery — Remove it, clean it, check its condition and water level, then charge it. Store it in a place that’s cool and dry, out of direct sunlight. Check the water level and charge it periodically during the storage period.

Portable fuel tank — Disconnect the hose from the tank. Remove the hose from the engine if the fitting is a quick-disconnect. If not, and the hose is secured to the engine, leave it connected. Secure the hose to protect it.

, or equivalent.

Evinrude/

With the propeller removed, check the gearcase for leakage. If leakage is evident, the gearcase seals should be replaced. See your DEALER.

Anticorrosion anodes — Check condition. Refer to Anticorrosion Anodes.

Install the propeller unless you will run the engine on a flusher for your pre-season servicing. If so, install the propeller after you shut OFF the engine and disconnect the flusher. Refer to Flushing.

Refer to Propeller to install the propeller.

WARNING

Prevent injury from contact with rotating propeller; remove the propeller before flushing.

Top off fuel tank with fresh fuel.

WARNING

Store fuel tanks in a well-ventilated area, away from heat and open flame. Prevent escape of liquid or vapors which could accidentally ignite. Close the filler cap vent screw, if equipped. Be sure the disconnected fuel hose does not drip.

PRE-SEASON SERVICE

Remove your outboard from storage and prepare it for a season of reliable service by performing a general check and a few preventive maintenance procedures.

Examine all loosened or removed hardware and any steering, throttle, and shift systems. Replace damaged or missing parts with

Genuine Parts

or equivalent.

Evinrude/Johnson

WARNING

Failure to carefully reattach the outboard and its control systems with factory-specified hardware can result in sudden, unexpected loss of boat control.

Battery — Charge fully and install. Refer to Battery.

Follow Engine Starting and start the engine. Let it idle while you:

Observe running quality – if poor, refer to Trouble Check Chart or see your DEALER.

Observe water pump operation. Water must flow from the water pump indicator in a steady stream. If it does not, shut OFF the engine and investigate. Refer to Engine Overheating.

Stop the engine and check the fuel system for leaks.

WARNING

Failure to check for fuel leakage could allow a leak to go undetected, resulting in fire or explosion.

32 - Maintenance

Page 35

BATTERY

Each outboard needs one battery that is:

• 12-volt, heavy-duty, designated "marine";

• Vented/refillable or maintenance-free; and

• Rated according to the minimum requirements in Engine Specifications.

Deep-cycle batteries are suitable IF they meet or exceed the minimum CCA requirements.

Ask your DEALER about your outboard’s requirements before installing longer battery cables, a battery switch or a battery insulator.

Installation

Read and understand the safety information supplied with your battery BEFORE you begin installation.

IMPORTANT: Place the battery in a hold-down system and in a location that is easily accessible for frequent checking and recharging.

Place a large-surface star washer over the battery’s positive (+) post. Stack the RED battery cable from the motor on the star washer, then install cables from accessories (if any). Finish the connection with a hex nut and tighten it firmly with a wrench.

Connect the motor’s BLACK battery cable to the battery’s negative (–) post in the same manner.

WARNING

Keep the battery connections clean, tight and insulated to prevent their shorting or arcing and causing an explosion. If the battery mounting system does not cover the connections, install covers. Check often to see that connections stay clean and tight.

1. Large surface star washer

2. Cover

Tighten all connections securely and coat the installation with

IMPORTANT: DO NOT use wing nuts on battery connections even if they came with the battery. Wing nuts can loosen and cause errant warning signals or electrical system damage.

Service

Before servicing the battery or the outboard, remove both battery cables from the battery, BLACK (–) cable first. Keep metal objects from contacting either battery post.

IMPORTANT: Service electrical components only while the outboard is NOT running. Be careful when identifying positive and negative battery cables and posts. If you touch the wrong post with a battery cable, even briefly, the charging system will be damaged.

Triple-Guard

grease.

WARNING

Battery electrolyte is acidic — handle with care. If electrolyte contacts any part of the body, immediately flush with water and seek medical attention.

Maintenance - 33

Page 36

ADJUSTMENTS

Idle Speed

The idle speed adjusting knob is located at the end of the steering handle. Before turning the knob, be sure the throttle is at SLOW and the motor has reached normal operating temperature:

• Increase idle speed – turn knob clockwise

• Decrease idle speed – turn knob counterclockwise

Tilt Friction

The tilt friction nut should be adjusted ONLY enough to control return of gearcase from tilt to normal (vertical) position.

1. Tilt friction screw

1. Idle speed adjusting knob

If your engine displays poor running quality at idle, ask your DEALER to perform the necessary adjustments.

Carburetor

High speed fuel calibration is maintained by the

fixed high speed jet in the carburetor. Fixed jets are not adjustable.

Low speed fuel calibration is set at the factory with a range of adjustment provided. If your engine displays poor running quality at low speed or idle, ask your DEALER to perform the necessary adjustments.

Steering Friction

The steering friction was set on your new motor before it left the factory. After the first 10 hours of service, check to see that it is still correct. A slight drag should be felt when turning the motor. If adjustment is necessary, turn the adjustment screw:

• Clockwise to increase friction; or

• Counterclockwise to decrease friction.

1. Steering friction adjustment screw

34 - Maintenance

WARNING

DO NOT overtighten for “hands-off” steering. Reduced steering control could result.

Page 37

LUBRICATION

Gearcase

Replace gearcase lubricant after first 10 hours of operation. Check level and condition of lubricant after next 50 hours of operation. Add lubricant if necessary.

Thereafter, check level and condition of lubricant every 50 hours. Replace lubricant every 100 hours of operation or once each season, whichever occurs first. Refill with If not available, lubricant can be used, however, long term durability may be affected with continued use. See your DEALER.

IMPORTANT: The recommended gear lubricants include special additives for marine applications. Do not use automotive gear lubricants, 2-stroke or 4-stroke engine oil, or any other oil or grease for gearcase applications.

With motor in normal operating position:

1) Remove drain/fill plug and lubricant level plug from side of gearcase and completely drain gearcase of old lubricant.

2) Examine drained lubricant for metal filings, milky appearance, or black color with burnt odor. If old lubricant has any of those characteristics, see your DEALER. If drained lubricant is in good condition, continue.

3) Place tube of lubricant in drain/fill hole and fill slowly until lubricant appears at lubricant level hole. See Engine Specifications for gear- case capacity.

4) Install lubricant level plug before removing tube from drain/fill hole. Drain/fill plug can then be installed without loss of lubricant.

5) Securely tighten both plugs.

Ultra-HPF

Hi-Vis®

gearcase lubricant.

or other marine gearcase

Lubrication Points

Refer to Engine Maintenance and Inspection Schedule for lubrication frequency and recom-

mended lubricant.

1. Starter pinion shaft

1. Cam follower, carburetor, and throttle linkage

1. Drain/fill plug

2. Lubricant level plug

3. Shift cradle screw – DO NOT REMOVE.

Maintenance - 35

Page 38

FUEL PUMP FILTER

1. Spark advance linkage

The fuel filter is located in the motor’s fuel pump. An authorized vice the fuel filter.

Evinrude/Johnson

DEALER should ser-

WARNING

Prevent excessive fuel spillage by disconnecting fuel hose from motor before disassembly.

The filter is located under the inlet cover on the fuel pump. To service, proceed as follows:

If portable tank is used, disconnect the fuel hose from the motor before servicing the filter.

Loosen screw and remove the cover. Do not lose O-rings.

1. Choke, shift lever, shaft and detent

1. Swivel bracket, clamp screws, tilt/run lever shaft, and tilt shaft

1. Cover

2. Filter

3. O-rings

Wash filter with clean solvent; blow dry. Reinstall filter, keeping lip of filter screen toward

fuel pump body. Install large O-ring in its groove in the cover and the

small O-ring around center post of pump body. Replace O-rings if cut or damaged. Reinstall cover. Tighten cover screw securely; clean up spilled fuel. Check for leaks – connect fuel hose to motor and

squeeze primer bulb until firm.

WARNING

Failure to inspect your work could allow fuel leakage to go undetected, becoming a fire or explosion hazard.

36 - Maintenance

Page 39

SPARK PLUGS

PROPELLER

WARNING

The ignition system presents a serious shock hazard. The primary circuit operates in excess of 250 volts; the secondary circuit operates in excess of 25,000 volts. Use caution to avoid injury from shock or injury resulting from your reaction to shock. Do not handle primary or secondary ignition components while the engine is cranking or running.

Inspect spark plugs periodically. Replace if electrodes are badly worn, insulators are cracked, or if they are badly fouled.

To remove spark plugs, twist and remove all spark plug leads. Unscrew spark plug from cylinder head.

To install spark plugs, wipe spark plug seats clean with a clean rag. Install spark plugs finger tight, then tighten to specified torque. Refer to Engine Speci-

fications.

IMPORTANT: Avoid engine damage by installing

spark plugs into COOL cylinder head and not overtightening.

Before installing the spark plug lead, apply a light coat of the spark plug. This will help prevent corrosion between the spring terminal and the spark plug.

Triple-Guard

grease to the ribbed portion of

WARNING

When servicing the propeller, always shift the outboard to NEUTRAL position, and twist and remove all spark plug leads so the engine cannot be started accidentally.

IMPORTANT: Apply

tire propeller shaft before installing the propeller. At least annually, remove the propeller and check for debris. Clean the shaft and regrease it before reinstalling a propeller.

Installation

Slide thrust washer onto shaft with fish line trap groove facing forward.

Slide propeller onto shaft, engaging the splines and seating it on the thrust washer.

Slide spacer onto the shaft and engage the propeller shaft splines.

Wedge a block of wood between the propeller blade and the antiventilation plate.

Triple-Guard

grease to the en-

1. Ribbed portion of the spark plug

Install propeller nut and tighten securely.

Maintenance - 37

Page 40

Continue to tighten propeller nut until nut slots and cotter pin hole are aligned. Install new cotter pin and bend ends to secure.

1. Thrust washer

2. Spacer

3. Propeller nut

4. Cotter pin

Fish Line Trap

The thrust bushing contains a built-up groove as a trap for fish line. Every 15 to 20 hours of operation, or whenever you suspect the presence of fish line, remove the propeller and check the trap. Remove any debris.

1. Fish line trap groove

Remove block of wood. Make sure engine is in NEUTRAL; give propeller a spin. It must turn freely.

Repair

If your propeller hits a solid object, the impact is partially absorbed by the rubber bushing in the hub to help prevent damage to the engine. A strong impact can damage the hub and propeller blades. Damage to blades can cause unusual and excessive vibration. Damage to the hub can cause excessive engine RPM with little forward movement.

IMPORTANT: Avoid or limit operation using a damaged propeller. Carry a spare propeller.

Keep your propeller in good condition. Use a file to smooth slight damage to blade edges. See your DEALER for repair of serious damage.

IMPORTANT: Fish line can damage propeller shaft seals. Damaged seals can allow water to enter the gearcase, causing internal damage.

38 - Maintenance

Page 41

ANTICORROSION ANODES

Your motor is equipped with one or more anodes that protect it from galvanic corrosion. Refer to Fea- tures for anode location. Disintegration of the anode is normal and indicates it is working. Check each anode periodically. Replace anodes smaller than 2/3 their original size. See your DEALER for replacements.

Galvanic corrosion destroys underwater metal parts and can occur in fresh or salt water; however, salt, brackish and polluted waters will accelerate corrosion.

Metal-based antifouling paint on the boat or motor and the use of improperly installed shore power in the area of your moored boat will also accelerate corrosion.

IMPORTANT: NEVER paint the anode, its fasteners, or its mounting surface. Painting will reduce its corrosion protection.

Maintenance - 39

Page 42

AC LIGHTING

1. Sleeve

2. Electrical tape covering connection

3. Light bulb Y – Yellow wire YG – Yellow/Grey wire YB – Yellow/Blue wire

Some models have an AC (alternating current) lighting system for operating lights on a boat. An AC lighting system is available as an optional kit.

IMPORTANT: Alternating current is generated and MUST NOT be connected directly to a battery. For battery charging, install a battery charging kit. See your DEALER.

Various combinations of light bulbs can be used. Use 12-volt bulbs of wattage sizes indicated on the diagram.

Follow the illustration for proper installation of wires.

40 - Maintenance

Page 43

TROUBLE CHECK CHART

IMPORTANT: If you are unable to identify or solve the problem, contact your DEALER.

SYMPTOM POSSIBLE CAUSE

Starter motor will not operate • Shift handle not in NEUTRAL.

• Battery and electrical connections loose or corroded.

Engine will not start • Not following starting instructions. Refer to Engine Starting.

• Fuel tank empty.

• Fuel hose disconnected, kinked.

• Fuel system contaminated with water or dirt.

• Fuel filter obstructed.

• Cold engine – Engine not choked.

• Warm engine – Engine flooded. Disconnect fuel hose at engine, push in choke, crank engine. If it starts, run until cleared. If it fails to start, wait a few moments and try again.

• Spark plugs incorrect. Refer to Engine Specifications.

• Spark plugs improperly gapped, carboned, burned or wet.

• Ignition system component failure.

Engine will not idle properly • Motor angle excessive.

• Spark plugs damaged or incorrect. Refer to Engine Specifica- tions.

• Fuel system contaminated with water or dirt.

• Carburetor mixture out of adjustment.

• Fuel/oil mixture incorrect.

Engine loses power • Spark plugs damaged or incorrect. Refer to Engine Specifica-

tions.

• Fuel filter obstructed.

• Fuel system contaminated with water or dirt.

• Water intakes obstructed and cooling system not operating correctly. Refer to Engine Overheating.

Engine vibrates excessively • Propeller shaft bent.

• Propeller fouled and restricted, blades bent or broken.

• Fuel system contaminated with water or dirt.

• Engine mount(s) damaged.

• Water intakes obstructed and cooling system not operating correctly. Refer to Engine Overheating.

• Carburetor mixture out of adjustment.

• Steering friction screw loose (if so equipped).

Engine runs, but makes little or no progress

• Propeller hub loose, slipping.

• Propeller blades bent or missing.

• Propeller shaft bent.

• Propeller fouled and restricted.

Maintenance - 41

Page 44

ENGINE MAINTENANCE AND INSPECTION SCHEDULE

Routine maintenance is necessary for all mechanized products. Periodic maintenance contributes to the product’s life span. The following maintenance chart provides guidelines for engine maintenance and inspection scheduled to be performed by you and/or by an authorized DEALER. The schedule should be adjusted according to operating conditions and use.

The recommended lubricants have been formulated to protect bearings, gears and engine components. They must be used to avoid damage caused by improper lubrication.

IMPORTANT: Schedules for rental operations, commercial applications or high hour use will require greater frequency of inspection and maintenance.

Engine Maintenance and Inspection Schedule

Frequency

Engine

Care

Description

Clamp screws, lubricate

(1)

Tilt/run lever shaft / tilt shaft, lubricate

(1)

Product

Each Use

10-Hour

Inspection

Every 50 Hours

or 6 months

Every 100 Hours

or Annually

7 Every 60 days / Every 30 in Saltwater

Every 200 Hours

or Biannually

Swivel bracket / tilt support bracket, lubricate

Shift lever shaft and detent / shallow water drive bracket, inspect and lubricate

Engine cover latch, lubricate

Throttle and shift linkage, lubricate

Choke, carburetor linkage / starter lockout, inspect and lubricate

(1)

7 Every 60 days / Every 30 in Saltwater

Fish line trap, inspect Every 60 days / Every 30 in Saltwater

Anticorrosion anodes, verify operation O D

Water intake screens, verify condition O D

Overboard water pump indicator, verify operation O D

Steering system check, verify function O D

Throttle and shift operation, verify function O D

Emergency stop circuit and lanyard, verify function O D

Flush cooling system O

Emergency Start Cord, onboard and inspect O

Operator’s Guide, onboard O

Clamp screws, tighten O

Engine upper and lower motor covers, clean and wax

Operator’s Guide, review O

Fuel filter inspection, eliminate contamination D

Fuel system components, inspect and repair leaks

(2)

Fastener inspection, tighten loosened components D D

42 - Maintenance

Page 45

Engine Maintenance and Inspection Schedule

Frequency

Engine

Care

Description

Product

Each Use

10-Hour

Inspection

Every 50 Hours

or 6 months

Engine to transom mounting hardware, re-torque D D

Cam follower, inspect and lubricate D D

Spark advance linkage, lubricate D D

Electric starter, lubricate D D

Every 100 Hours

or Annually

Every 200 Hours

or Biannually

Electrical and ignition wires and connections,

inspect

Gearcase lubricant replace 5 D D

Powerhead synchronization and linkage, inspect

Gearcase lubricant, inspect fill level and condition of

(2)

7D D

lube

Starter pinion shaft, inspect and lubricate

(3)

Propeller shaft splines, inspect and lubricate 7 D

Spark plugs, replace

(2)

Decarbonize 10 D

Driveshaft splines, inspect and lubricate 8 D

Water pump, inspect and replace D

(1) Also recommended at 10-Hour Inspection

(2) Emission-related component

(3) Do not use light duty penetrating lubricants

D Dealer Performed Service

O Operator Performed Service

Evinrude/Johnson

Ultra-HPF

Power Trim/Tilt Fluid

Triple Guard

Evinrude/Johnson Moly Lube™

Starter Bendix Lube Only P/N 337016

Evinrude/Johnson

gearcase lubricant

grease

anti-corrosion spray or

P/N 175356

Engine Tuner

Evinrude/Johnson

“6 in 1” multi-purpose lubricant

Maintenance - 43

Page 46

NOTES

44 - Maintenance

Page 47

Maintenance - 45

Page 48

INSTALLATION

WARNING

Your engine must not exceed the maximum horsepower indicated on the boat’s capacity plate. Such overpowering can cause loss of control. Contact your DEALER or the boat’s manufacturer if your boat lacks a capacity plate.

Boats designed for remote-steered engines might be overpowered by a tiller-steered engine of the maximum rated horsepower. Ask your DEALER or boat manufacturer is you are unsure about your boat’s suitability.

Transom Height and Shaft Length

The transom height dimension listed in Engine Specifications is the height of the boat transom

your engine needs. This dimension is measured at the transom centerline, perpendicular to the bottom of the boat.

Incorrectly matched boat and engine transom heights can cause boat instability and loss of control. Refer to Transom Height and Shaft Length.

Prevent lateral movement and possible engine loss by using the mounting hardware supplied or hardware of sufficient size, strength, and quality. Refer to Installing the Engine.

A mounting surface that is damaged or too thin to support your engine while underway might fail during operation, causing you to lose control. Be sure the boat’s transom or mounting bracket is structurally sound and between 1 1/2 in. (38 mm) and 2 1/4 in. (57 mm) in thickness.

1. Transom height

2. Antiventilation plate

3. Final position – 0 to 2 in. (0 to 51 mm)

Use this procedure to determine whether or not the boat’s transom height is correct for the engine’s shaft length:

Lift the engine using the lift grips (NOT the tilt grip or steering handle) and place it in the center of the boat’s transom.

46 - Maintenance

1 1

1. Lift grips

Page 49

If equipped, tighten clamp screws by hand, NOT with tools.

Adjust the motor angle so the antiventilation plate is parallel with the boat bottom. Refer to Motor Angle Adjustment.

The resulting position of the antiventilation plate must be no higher than the boat’s bottom and no lower than 2 in. (5,1 cm) below it.

If the resulting position of the antiventilation plate is above or below the 0 to 2 in. (0 to 5,1 cm) range, the engine shaft length must be changed or the boat’s transom must be modified.

If you install and operate the engine:

Lower than recommended — Serious powerhead damage could result from water entry into the lower engine cover or overloading from an under-revving propeller at wide open throttle.

Installing the Engine

WARNING

IMPORTANT: Follow all directions carefully. The

engine’s warranty will not cover product damage or failure that results from incorrect engine installation.

WARNING

Higher than recommended — Serious powerhead damage could result from inadequate cooling or an over-revving propeller. Propeller ventilation (slippage) often occurs, resulting in poor boat performance.

On a specialty hull, non-planing hull, or on a boat with a curved transom, these guidelines might not apply. See your DEALER for special installation information.

Even if equipped with clamp screws, your engine must be bolted to the boat to prevent it from “working off the transom” during operation.

Center the engine on the boat’s transom (or mounting bracket) and tighten the clamp screws by hand, NOT with tools. See your DEALER for an accessory transom plate to protect the boat’s transom.

Maintenance - 47

Page 50

Bolt your engine to the boat’s transom using the mounting hardware provided.

1. Clamp screws

2. Transom plate

3. Engine retention lug

The stern bracket has two holes on each side of the engine. Drill only one hole on each side. Use the upper holes unless your situation requires using the lower holes. Be sure to drill at right angles to the transom.

Apply polysulfide sealant generously behind the heads and to the shanks of the mounting bolts before inserting them and to the surfaces of washers that contact the transom. Avoid RTV silicone and polyurethane sealants as they can be dissolved by gasoline.

Secure the engine with the mounting hardware. After 30 minutes of operation, retighten clamp

screws by hand. DO NOT use tools to tighten clamp screws. Check clamp screws regularly.

Connect a safety line between the engine retention lug and a secure place on the boat. If the engine should come off the transom during operation, a strong safety line will keep it from being lost.

After positioning the engine, use the stern brackets as a template for location and size of holes to drill in the transom.

WARNING

When replacing bolts, screws, or other fasteners, use alent strength and material.

Johnson

parts or parts of equiv-

48 - Maintenance

Page 51

CHANGE OF ADDRESS / CHANGE OF OWNERSHIP

If your address has changed or if there has been a change of ownership, be sure to fill out and mail the card provided on this page.

Such notification is likewise necessary for your own safety even after expiration of the original warranty, since Bombardier will be in a position to contact you if correction to your outboard becomes necessary.

Outside the U.S. and Canada, this card should be sent to the Bombardier division where the outboard was registered. Please contact your Dealer or Distributor.

Change of address Change of ownership

Model number

Serial Number

Old address / Previous owner

Last name

First name M.I.

Address

City State

Zip code Country

Phone number

Signature Date

New address / New owner

Last name

First name M.I.

Address

City State

Zip code Country

Phone number

Signature Date

00006

Maintenance - 49

Page 52

Page 53

Your DEALER

Name:

Address:

Operator’s Guide

Confirmation of Receipt

Upon delivery of your new DEALER will take receipt of the form for their records.

Receipt

Name:

Address:

Owner of Model No:

Evinrude/Johnson

Serial No:

Outboard, complete and sign the form hereunder. Your

(To be completed by customer or selling DEALER)

The DEALER named on this document has instructed me on the operation, maintenance, safety features and warranty policy, all of which I understand and agree to be bound with. I am also satisfied with the predelivery set-up and inspection of my copy of the Operator’s Guide.

Signature:

Date:

Evinrude/Johnson

Outboard. I have also received a

Maintenance - 51

Page 54

52 - Maintenance

Page 55

Readiness Test and a Final Word to the Owner/Operator

The Operator’s Readiness Test....

1. Did you read this Guide from front cover to rear cover?

2. Are you ready to take responsibility for the safe operation of your boat and motor?

3. Do you understand all the safety precautions and instructions contained in this Guide?

4. Do you understand that this Guide contains essential information to help prevent personal injury and

damage to equipment?

5. Are you ready to follow the recommendations in this Guide and take a boating safety course before you operate your boat and motor?

6. Do you know who to ask if you have any questions about your boat and motor?

7. Do you know your local marine traffic laws?

8. Do you understand that human error can be caused by carelessness, fatigue, overload, preoccupa-

tion, unfamiliarity of operator with the product, drugs and alcohol, just to name a few?

WARNING

It is impossible for this Guide to cover every hazardous situation you may encounter; however, your understanding of and adherence to essential information contained in this Guide will build good judgment when boating. Always be alert and careful: a good foundation for safety.

Page 56

*215483*