John Lewis 800/65503 Instructions Manual

Stock number: 800 / 65503

John Lewis

Woodstock Guest Bed

Thank you for purchasing this Woodstock Guest Bed. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.

For product support or spare parts please call
the John Lewis Helpline;

T: 01244 689949

E: [e-mail]

This product is Heavy, it should be assembled as near as possible to the point of use. TAKE CARE

WHEN LIFTING

to avoid personal injury and (or) damage to the product.

This product takes approximately

40 MINUTES to assemble with 2 PEOPLE.

The fittings pack contains

SMALL PARTS which should be KEPT AWAY FROM YOUNG

CHILDREN

.

Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product plase call the John Lewis
Helpline on 01244 689949 or e-mail [e-mail]

PRE-ASSEMBLY PREPARATION

Please ensure instructions are read in full before attempting to assemble this product

Single

Please check the pack contents before attempting to assemble this product. A full checklist of components
is given in this leaet. If any components are missing, please contact the John Lewis Helpline.

Fitting and parts checklist

Headboard x1

Footboard x1

Side Rails x2

Slats x1

M8 x 22mm Bolt x8

M4 x 3mm Screw x8

Allen Key x1

Parts

Step Two

Step by step assembly instructions

Step One

Fix the Siderails (3) to the Headboard (1) and Footboard (2) using Bolts (A) as shown in the diagram below.
Tighten using Allen Key (C).

Repeat for all 4 corners.

Lower the Slats (4) onto the Siderails (3) and secure using Screw (B) as shown in the below diagram.

Underbed Assembly Instructions

Head Panel x2

Leg Cross Rail x2

Siderails with Legs x2

Slats x1

M6 x 80mm Bolt x4

M6 x 60mm Bolt x8

M6 x 13mm Barrel Nut x12

4 x 35mm Screw x8

10 x 40mm Dowel x12

30 x 50mm Castor Wheel x4

4 x 15mm Screw x8

Allen Key x1

Fittings and Parts Checklist - Underbed

Step One

Attach the Castor Wheels (F) to the Siderails with the legs (3). Secure by using Screw (G) as shown below.

Caution: Please do not place the truckle upon its side
as it features a spring mechanism that could cause
potential injury.

Step Two

Insert the Dowel (E) into the holes indicated on the legs of the Siderails (3). Attach the Legs Cross Rail (2) to the
legs by using Barrel Nut (C) and Bolts (A). Tighten them by using Allen key (H). Repeat this process on both
sides of the Legs Cross Rail (2) as shown in the diagram below.

Caution: Please do not place the truckle upon its side
as it features a spring mechanism that could cause
potential injury.

Step Three

Insert Dowel (E) into the holes on the Siderail (3). Attach the Head Panel (1) onto the Siderail (3) using
Bolts (B) and Barrel Nut (C). Tighten using Allen Key (H). Repeat this process for each side of the Head Panels (1)
as shown in the diagram below.

E

8

8

Caution: Please do not place the truckle upon its side
as it features a spring mechanism that could cause
potential injury.

Step Four

Starting at the head end, attach the Slats (4) using Screws (D). Please ensure that the rst Slat (4) is placed as
close as possible to the Head Panel (1) before securing into place. Next, pull the Slats (4) down to the footend.
Ensuring the Slats (4) are covering the full length of the bed, secure using Screws (D). Finally secure the middle
Slats (4) into place using Screws (D).

Care and Maintenance

Safety Instructions

Never drag furniture when moving it, always lift it.

Do not use this item if any components are missing or damaged.

It is recommended that before moving heavy objects to a new location they are completely dis-assembled

If you require any additional information or have any issues with this product please call the John Lewis
Helpline on 01244 689949 or e-mail [e-mail].

John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com

Please take care when handling or moving the furniture as careless handling may cause damage or
injury. Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent
adult. No liability will be accepted for damage or injury caused by incorrectly installed or assembled
furniture. During assembly children should be kept away from the product due to possible risk of injury.

This product complies with BS 1725:1998

This Woodstock Guest Bed should be cleaned using a soft damp cloth and dry immediately. Do not use a
very wet cloth or allow any liquid contact for a long period of time as this cam permanently damage the
surface.

Do not use abrasive cleaner or harsh detergents as this can damage the surface. Do not drag any object
across the bed as this can cause permanent damage.

Please retain this information leaet for future reference.