HOT TUB
Model SPA-8098
OPERATING INSTRUCTION
1
1. I、Illustration to buttons
Fig.1：Control Panel
“
“
“
“
“
“
MIN
”Frequency up- searching / Minute
HOUR
” Frequency down- searching/ Hour
+
” Volume up/ Set switch
-
” Volume down/ Open
MEM
” Radio channel Menory/ Lock
SET
” Radio channel read / Close
“ ” Lasting Circulation Cleaning On-off
“ ” On-off/Setting confirm
“ ” Radio or CD Switch/ On-off
“ ” view pump
“ ” Spa Light On-off
“ ”Surfing pump 1 On-off
“ ” Surfing pump 2 On-off
“ ”Surfing pump +circulaltion pump On-off/Set
Circulation Cleaning Time
“ ” Heating On-off / Set Pre-heating “ ” Set Temperature
Note：
.The functions listed with bule letters only works on the condition of on-off
II、Function Summary
1、Max. with 6 KW heating system, set pre-heating, set and display temperature
2、Max. with 3 surfing pumps,1circultion pump,view pump, and 1 blower.
3、Set Ozone. Set Spa lights.
4、CD audio-input / Display of radio frequency and preserve 10 channels
5、Volume di splay and 87 frequency adjustment
6、Circulation cleaning/set time for circulation cleaning
2
7、24 hours display and set time
8、 Menoery preserve once power off
9、Fahrenheit & Celsius degree switch
10、Antifreezing functions
11、Keys with backlight
12、Lock settingl
13、Three-phase or single-phase, available of 110-120VAC or 220-240VAC
14、Choice with offering a AC for circumscribing DVD or TV
15、Choice with power control
16、Choice with galvanoscope device
III、Operation
Fig.3：Temperature Normal Display Fig.4：Senor on/short circuit display
1、When you first start the spa, the backlight will be dimmed and the LCD will show the current time and
temperature. If there is a problem with the circuit board the controller will display the code “E1”. When
the radio frequency is displayed as “---” it indicates that the spa is in “power off” model, and
pre-heating and circulation cleaning function is off.
2、Lock memory Mode(optional function)：
MEM
The memory lock will start work by pressing “
spa has not been adjusted for a period of 30 minutes. When the memory locked key is pressed TWICE
MEM
“
” the spa will become unlocked and the word “LOCKED”will disappear.
” key in the status of “power off”whe n the
3、Adjusting Time：
In the status “Power off” and the pre-heating and circulation cleaning are not starting. Pressing
MIN
“
pressing
without stopping. The hour adjustment range is
”or“
“
HOUR
” adjust time . The Minute and Hour display flash at this time. It will add 1 hour when
HOUR
” each time and the hours can be adjusted continually when pressing the “
0-23.
HOUR
”
In the status of time setting
could be added continually when pressing the
0~59
The system will quit the time-setting status automatically after 6 seconds without pressing any buttons
It will add 1 minute when pressing “
“
MIN
” each time and the minutes
MIN
” without stopping. The minute adjustment range is
3
4、Set pre- circulation-cleaning：
In the pre-set mode circulation will be automatic once per day. The display will show clearly whether
circulation is in action or not. See following Fig 5-6
：
AM
AM
Fig.5：Circulation-cleaning off Fig.6：Circulation-cleaning on
When setting the Circulation-cleaning the display must be in the “Power off” status and the LCD display “---”
1） 、Press“ ” to enter Circulation-cleaning setting mode and the LCD showes and flashes “ ”,and
then the circulation workes on.Press “
” again to off the circulation cleaning,and the “ ” will
disappear.
2)、Press“
”（minutes）and“ ”（hours to adjust the time.
It will add 1 minute when pressing “
when pressing the
“
MIN
” without stopping. The adjustment range is 0~59.
MIN
” each time and the minutes could be added the continually
It will add 1 hour when pressing
when pressing the
After setting the circulation cleaning pre-set timing, go to next step
“
HOUR
“
HOUR
” without stopping. The adjustment range is 0-23.
” each time and the hours could be added the continually
.
4
1） circulation
2）
Set start of circulation
3） Set lasting time for circulation
4）
Finished
3)、Press“
not flash. It will add 5 minutes by pressing
time。The maximum working time is 19hours and 55 minutes.
to the next setting.
If all settings have been correctly, set Press “ ” for confirmation , the system will quit this mode
4)、
automatically(press key “
” to set the circulation times; it will show the minimum(5 minutes) on the LCD and this time will
“ ” each time. It will add 1 hour by pressing“ ”each
When you have completed this procedure continue
” to clear settings and exit).
***Notice***
1 All the setting of Circulation-cleaning must be set on Power OFF status
2 Circulation PUMP and OZONE are not working while setting the circulation
cleaning.
5、Set preheating (if required)：
Only one pre-heating setting is allowed each day if required.The LCD can show clearly in the following
figures whether pre-heating settings are set or not
See following Fig.7-8：
5
ON
Fig.7：Pre-heat On 图 8：Pre-heat Off
Pre-heating is set when the spa is in the “Power off” status and the LCD display shows “---”
OFF
1）
Set preheating
2） Time setting for Preheating
3） Continual time of preheating
4）
Preset temperature
5）
Finished
1） 、Press “” and enter Pre-heating setting mode, and the LCD flashes of “ON” ,Press“ ” can
turn on the pre-heating setting and pressing
“ ”again , will turn off the pre-heating. “ON/OFF” on
LCD will show “ON” and will not flash. Press
without flashing. When the system enters into pre-heating mode, the setting time will flash on the LCD (this
time is the pre-heating time) at this moment, only
“ ” to turn off pre-heating. The LCD will show “OFF”
“
MIN
”and “
HOUR
” are available to change the
6
time
2)、It will add 1 hour when pressing
HOUR
the
“
” without stopping. The adjustment of hours is 0-23
“
HOUR
” each time and hours could be added continually when pressing
It will add 1 minute when pressing “
pressing the
“
MIN
” without stopping. The adjustment range is 0~59
MIN
” each time and minutes could be added continually when
After time setting of pre-heating, proceed to the next step.
VOL+
2） 、Press“
And this time will not flash on LCD screen. It will add 10 minutes by pressing
it will add 1 hour when pressing
hours and 50 minutes. When you have correctly set the pre-heat times you may proceed to the next step.
4)、
Press “
setting temperature. The range of temperature setting is:
SET
” to set the continual for pre-heating. It will show the minimum continue time is 10 minutes.
MIN
“
HOUR
“
VOL+
SET
” again It will show “ SET” on the LCD panel. Press “ ” button to change the
” each time. Please note that the maximum continual time is 19
” each time and
15~45℃。
5)、When ev erything is set correctly, press the “ ” to confirm, the system will quit the pre-heating setting
mode.
***Notice***
1、All setting of preheating must be in Power OFF mode, just turn on the spa，the
LCD will display “---”
2、Please note that it shows "on" or "off" on the LCD. "on" means preheating is
turned on mode. when the time of pre-heating is as same as current time, the heater
will start working. "off" means the heater won’t start to work an any time.
3、Circulation PUMP and HEATER without working while setting preheating.
6、Operation of preheating：
When the preheating time is as same as the current time, the LCD screen shows “on” and the tub is also
filled with water. The heate r will st a rt to work. The heater, circulation pupm and time counting work atsimultaneity.
The countdown time will be shown on the LCD screen, till the preset time is finished.
During the preheating, The preheating will be turned off automatically once the preset time is finished.
ON/OFF
Or Pressing the
***Notice***
i. When setting temperature is lower than or equal with water temperature，
“ ”or“
”key can stop preheating.
Even the Preheating is on, but the circulation PUMP and HEATER are not
7
working。
ii. When the HEA TER is “I” type frame，The power of circulation PUMP must
reach 750W。Otherwise the heater won’t work due to not enough water
pressure to drive pressure switch.
iii. Conditions meet the above “2”，and the HEATER is still not working，Please
short the line of water pressure switch。
7、Circulation-cleaning：
As the current time is as same as the preseting time, the preset is “on” too and the tub is filled with water, the
circulation cleaning will start, the circulation pump works at the same.. The LCD shows the countdown time. All
the surfing pumps and blower will work for 30 seconds at every 30 minutes. The Ozonier works at every 15
minutes
the
.
The circulation cleaning will be turned off automatically once the countdown time is finished or By pressing
“ ” key to turn off directly.
8、Operation to Power ON/ OFF
Pressing the key “ ” in “power-off” status to enter the “power-on” status. To pressing the in the
status of “power-on” to enter the “power-off” status. The LCD screen shows the on or off.See following Fig.9-10
AM
OFF
Fig.9：OFF Fig.10：ON
AM
OFF
9、Temperature setting：
In the status of “Power-on” and “HEATER” is working.It will add 1 centigrade by press “ ” each time，
temperature will be added continually til reach 45 centigrade by press “ ” without stop.Press “ ”
the
again，and the
temperature is show 15℃。The range of adjustment is：15~45℃。
10、Operation Radio & CD：
AM
PUMP3
Fig.11：Radio frequency is 105.2 MHZ，Save the present frequency to channel 3 (Save channel)
or Exchange the frequency form channel 3 to the present (Searching channel)
I、“ ” is the ON/OFF key for radio and CD。and it is only available in the status of power on. The
first pressing
on the CD at the same time，and the third pressing“
“ ” is turning on the radio，the second pressing “ ” will turn off the radio and turn
” ，will turn off the radio and CD simultaneous。
8
Ⅱ、LCD will show present frequency and volume of the radio after turning on the radio。
Ⅲ、In the working of radio， The volumle of the present radio frequency can be changed by pressing
MIN
“
”and “
Ⅳ、Pressing the key “
SET
“
channel by pressing this key continually。If none of the channel， LCD will display “---”。
” continually will take out the memorized radio frequency from channels will be saved at present
Ⅴ、Press the key “
MEM
“
10，Name of channel is 0-9。
” continually will memorize the present radio frequency in different channel。 The channel of max is
Ⅵ、The volume can be changed by pressing key “
HOUR
”
SET
” will take out the memorized radio frequency，Pressing the key
MEM
” could memorize the present radio frequency， Pressing the key
VOL+
SET
”and“
OPEN
”
11、Operation of Pump：
PUMP2
The Button , operates pump 1； The Button
PUMP3
operates pump 2；The button
operates pump 3，Also the pump 3 is the circulatio n pu mp。When pump 3 is turned on the LCD will show
“
heating, including pre-heating and circulation is about to start
”， whether the heating and circulation is on or off. The LCD will show when pump3 is off and the
12、Operation of lasting circulation cleaning：
Press the key “ ” at any time to turn on or off the lasting circulation cleaning, work mode is like the
preset circulation cleaning. The surfing pumps and blower work for 30 seconds at every 30 minutes. Ozonizer
works at every 15 minutes.
Once any surfing pumps or blower start, the ozonizer without working. The ozonizer can not work if the
circulation pump is without working.
IMPORTANT: Please ensure that the ozone function is not in use whilst bathing in the spa
13、Operation of spa lights：
Press the “ ” button to control the ON/OFF of the LED lights
For the first time pressing the key“ ”， the LED lighting on，and the colours is changed slowly；
For the second time pressing“
”，the current colour unchange；For the third time pressing
“ ”，Off the lights。
14、Setting the constant Temperature Settings：
1）、Pressing the “ ” button will start the constant temperature heating.
2）With the setting above, the circulation pump will work automatically.
3）、If the temperature is set at 35℃, when the water temperature reaches or exceeds 36℃, the heater
will be turned off automatically and the circulation pump will stop after 5 seconds. When the water temperature
reaches or is lower than 34℃, the heater will start up again.
9
4）、In the case of an error the LCD shows ”E1”. If this happens, the thermostatic heating sytem will NOT
be available, the heater doesn’t work.
15、Operating the Air Blower：
Press“ ” controls the blower
16、Fahrenheit & Celsius Temperature shift：
In the status of“Power off” pressing the key “ ” can change the mode of Fahrenheit & Celsius degree
17、When there is no water in the spa. All surfing pump s, blower and he ating system can not st art up. Ho wever
the corresponding signals will flash on the LCD.
18、Prevent freezing function:
The heater & circulation pump will work automatically once the water temperature is below 5℃, when the water
temperature is reach at 10℃, heating will stop. This function is only available while the spa is on
normal power supply.
IV、Electric parameters
1、
Performance index：
Rated voltage： 220V/50Hz Maximum working current：60 A/220V－240V～
Voltage-resistance：1250V/1 minute without penetration。 Isolative resistance：》10MΩ
Water resistance grade：IPX5 Electric shock resistance：first grade
(2) Output loading index
Heater： AC220V/3KW x 1 Surf Water pump： AC220V/3 HP x2
water pump：
Air pump： AC220V/0.7kw x 1
spa light： AC12V/5W x 1 Ozone：Ozone
water Radio：1) Frequency Range： FM： 87.0~108.0MHz
2) Maximum Output Power： 10W
5.Warning Information
a. Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
b. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
c. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision o r
instruction concerning use of the appliance by a person responsible for their safety.
d. Children should be supervised to ensure that they do not play with the appliance.
e. Details concerning cleaning and other maintenance
f. Maintenance of water purity, especially PH values and chlorine concentrations.
g. Cleaning and disinfection
h. Use and installation of a cover.
AC220V/2HP x2 pump：AC220v/1HP x 1
： 220V—240V/100W×1
3) Speaker：8Ωdamp proof speaker
10
i. Disposal of water
j. Precautions to avoid damage due to water freezing
k. Precautions to avoid damage when the appliance is left empty for extended period.
2.2 Sub-clause 7
The installation instruction shall state the substance of the following:
- Earthed appliances must be permanently connected to fixed wiring;
- The appliance should be supplied through a residual current device (RCD) having a rated resid ual operating
current not exceeding 30 mA.
- The floor has to be capable of supporting the expected load.
- An adequate drainage system has to be provided to deal with overflow water.
- Details of how to follow the wiring rules, for example, specifying that parts are installed in the correct zone
and that equipotential bonding is carried out.
WARNING
1、
2、Grounding is required. The unit should be installed by a qualified service representative and
3、FOR YOUR SAFETY-This product should be installed by a professional service
technician,qualified in hydrotherapy bath installation.
4、lt’s prohibited to cover the instrument with something while opeating.
5、when using at the first time ,Be sure there is water in heater pipe before staring.
6、parts containing live parts, except parts upplied with safety extra-low voltage not Exceeding
8、earthed appliances must be permanently connected to fixed wiring；
9、the appliance should be supplied through a residual current device (RCD)having a rated
10、If the mains cord of this appliance is damaged,It must only bereplaced by our service
DANGER：RISK OF ELECTRIC SHOCK，Connect only to a circuit protected by a Ground
Fault Circuit lnterrupter.
ground.
12V,must be inaccessible to person in the bath；
residual operating current not exceeding 30 mA.
representative,As special tools and/or parts are required
11
Solutions of Fault
Phenomenon Reason How to Solve the problem
No power supply
No display on control
panel
LED light not work
Ozone not work
Displaied “E1””FF” in
control panel
being incapable of
activate water pump,and
water pump icon
flashing
Heater not work, and
heating icon on panel
flashing
Leakage
1. The electric leakage switch was
breaked off
2. The Fuse be break off
1. The plug which connected with the
panel loose or disconnected
2. The Panel happened with malfunction
1. Power of the light be break off
2. Fuse be break off
3. light be burn
1. Ozonater burn
2. Fuse be break off
3. Cable of the ozonater be cut off
1. temperature detector be cut off or
shortcirculate
2. plug of the temperature detector be
nundated by water
1.water not achieve the appointed level
2. water detector not connect well
1. setting water temperature lower then
the water temperature
1. silicon plaster not good
2. PVC plaster not good
3. Blow out of the water pipe
1. Check and eliminate the malfunction,
restart the spa
2. Please change fuse
1. to connect the plug of the control
panel and the main box
2. Change a new control panel
1. To check if cable of the light is well
connected with main box or not
2. Change a fuse
3. Change a new lampwick
1. Change a new ozonater
2. change a fuse
3. check if the cable of the main power
is connected with the main box or
not.
1. Connect the temperature detector
2.Change a new temperature detector
1. To add more water to make it up to
the water detector
2. To re-connect the line of water
detector
1. set the temperature degrees higher
than the water in tub
temperature(between 15 and 43 °C。
1. To remove the jets then re-install
one
2. To plaster once again
Change water pipe
12
13
14
15
Loading...