
JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
Content
Front Panel ............................................................................... 3
Rear Panel ................................................................................ 3
Top Panel ................................................................................. 4
Side Panel ................................................................................ 4
Button/LED Indicate .................................................................... 4
Installation ............................................................................... 9
Package Contents ..................................................................... 10
Specifications .......................................................................... 10
Firmware Upload ...................................................................... 11
Update List ............................................................................. 13
Appendix Table A ..................................................................... 14

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
Feature
SDI Supports HD formats :
720p50 & 60
1080i50 & 60
1080p24, 25, 30, 50 & 60
SDI Support 525i & 625i SD D1 format
Auto 3G/HD/SD-SDI detection
Can be split one 3G-SDI displays simultaneously.
Frame rate conversion(1.000/1.001)
External Button Configuration
Firmware is upgradable in the field using the integrated USB port
The converter is Plug-and-Play
Support DVI-D, DVI-A, Component, CVBS and S-Video output
Front Panel
From your SDI Source plug into these ports
From your SDI Display Device plug into this ports
Select Format/Output Port
The Power adapter plug into here
Form you Audio Device plug into this port
Component/CVBS/S-Video
Output Port
From your YPbPr/CVBS/S-Video Device plug
into this port
From your DVI-D/DIV-A Device plug into this
port

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
The LEDs are indicate main output of source
The LEDs is indicate power and signal locked.
The LEDS are indicate main output of format
Upgrade firmware/Control Box From PC
Button/LED Indicate
1. Firmware Mode:
Hold on the 3 and 2 button, the display is showed firmware version on display

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
Pull all button (1, 2 and 3) at same time, the box auto reset to default.
Pull button 4 change to output source mode. The button 3 and 4 can be switch
output source.
a. DVI-D Output: (DVI-D + YPbPr)

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
Pull button 1 change to format mode, frame rate and Fraction by button 2 and
3.
b. DVI-A Output: (DVI-D + DVI-A)
Pull button 1 change to format mode, button 1 and 2 is change format

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
c. YPbPr Output:(YPbPr + DVI-D)
Pull button 1 change to format mode, frame rate and Fraction by button 2 and
3.

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
Pull button 1 change to format mode, frame rate and Fraction by button 2 and
3.

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
4. Pattern Genertor Mode:
input signal is plug out, the Box auto change to Pattern Genertor
mode. It is proivded the 13 of Mode
Installation
SDI2Multi installation consists of the following:
1. Disconnect +12DC adaptor to converter.
2. Connect Video Source (SDI) to the SDI Connector.
3. Connect Equipment to the output’s connector

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
4. Connect the +12DC adaptor to the converter.
Package Contents
The SDI2Multi package contains the following items:
User Manual x 1
+12 DC Adapter x 1
SDI2MultiConverter x 1
2.970Gb/s, 10485Gb/s and 270Mb/s
Stereo 2-Channel (L/R Audio)
3G: 120m of RG6/ 100m of RG59
HD: 200m of RG6/ 140m of RG59
SD: 400m of RG6/ 280m of RG59
*1 RG6: CANARE L-5CFB Cable / RG59: Belden 9275 Cable
*2 Cable Length Performance: Depending on SDI Signal and
Cable Quality

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
1 x DVI-I [DVI-D + DVI-A]
3 x BNC [YPbPr or YC + CVBS ]
1 x Phone Jack
3G 75 Ω inter-locked socket
Output Format/TV Wall/TV Ratio
L:104mm x W:63.3mm xH:26mm
Power Adapter: AC 100 ~ 240 V/DC (+6 ~ 15 V)
Firmware Upload
Firmware is upgradable in the field using the integrated USB port
How to Firmware upgrade:
Step1.
Open Upload Firmware Program tools.exe and connect box to PC by USB Cable.
Step2.
Plug and un-plug “DC adapter” to power on/off the converter box (the
connection check status will be changed to “Connect”)

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
Step3.
Plug and un-plug “DC adapter” again (the connection check status will be
changed to “Connected”) and Please click the Open File button to select the
firmware bin file.
Step4.
Please click “Start’ Button to proceed with new firmware programming.
The PASS message will appear when the procedures finished.
Step5.
Close Upload Firmware Program tools

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
1. Rename to SDI2Multi
2. Add Pattern Generator Function

JMC Systems Engineering AB www.jmc.se info@jmc.se +46-8-82 82 70
Appendix Table A
Support Input Format:
Support Output Format (DVI-A):