JL Audio Stealthbox SB-T-CAM/12W3v3, Stealthbox SB-T-CMRY/12W3v3 Installation Manual
I N S T A L L A T I O N G U I D E
for th e
SB-T-CAM/12W3v3
SKU#94437
2000
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. If you prefer to perform your own installation,
please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox
®
be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub- bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Remove any contents from the trunk so that you have a
clean area to work in.
Continued on Next Page
S T E P 2
Remove both of the hardboard floor inserts
S T E P 3
The Jack and it’s mounting foam will be removed from the
compartment on the passengers side of the trunk floor.
SB-T-CAM/12W3V3 INSTR_SKU# 011284
INS TALLATIO N
D I F F I C U LT Y :
35
OU T
OF
EST IMATED TIME:
23 HO URS
Continued on Next Page
SB-T-CAM/12W3V3 INSTR_SKU# 011284
S T E P 7
Align the jack so that the bolt that secures the spare can be
re-inserted thru the wheel and, jack thereby securing both in
the spare tire well.
S T E P 6
Use the strap that was removed in STEP 4 to secure the jack
to the spare wheel.
S T E P 5
Remove the spare tire and turn it over. Put the jack inside
the wheel and, expand it so that the pressure from the jack
holds it in place.
S T E P 4
Remove the strap that secured the Jack to the locating foam,
this will be re-used to secure the jack to the spare tire.
Page 2 • JL Audio, Inc 2008
S T E P 9
Remove the trunk liner fastening plug, this will be replaced
by one of 1/4-20 Rivet Nuts (see detailed picture of the Rivet
Nut below). Enlarge the hole using a 3/8” drill bit and, drill.
*CAUTION*
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
transmission lines, electrical wiring, exhaust systems
or anything else that might cause a reduction in
your weekly pay. Always wear eye protection when
drilling.
S T E P 1 1
The anchor point for the cargo net needs to be removed for
the installation of the Stealthbox®.
S T E P 1 0
Insert the 1/4-20 Rivet Nut into the appropriate hole and,
expand it by tightening a 1/4-20 x 5/8” Pan Head Phillips
Screw, once the 1/4-20 Rivet Nut has been expanded in
place, remove the 1/4-20 x 5/8” Pan Head Phillips Screw. The
procedure for installing the Rivet Nuts will be repeated three
times in total
(STEPS 9 & 15) as will be detailed.
S T E P 8
Re-install both floor panels that were removed in
STEP 2.
Install both of the brackets on the bottom of the enclosure as shown
Loading...