SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
®
be properly mounted to the vehicle
INSTALLATION
DI FFICU LTY:
OUT
OF
5
2
ESTIMATED TIME:
12 HOURS
INSTALLATION GUIDE
for the
SB-POL-RZG2SPKR/MX650
SKU# 94655
2014 & Up Polaris RZR XP 1000, RZR XP 4 1000
RZR 900 XC, & RZR 4 900
Enclosure Type: Sealed
Driver Type: MX650-CCX-SG-TLD-B
Nominal Impedance: 4 ohms
Continuous Power Handling: 60 watts (RMS method)
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
Continued on Next Page
INCLUDED HARDWARE / WIRING INFORMATION
Wire Size Wire Color Use
Yellow LED Negative (-)
BOM ID Qty SKU Description
- 1 150249 Foam Tape (not shown)
LED Wire Connections
will supply positive (+12V) power. Fuse this connection according to how
many LED circuits you have (LED circuits x 150A).
(hardware pictured for one)
1* 2 152414 Wire Harness (10’)
2 2 153820
1/4 - 20 x 1” Stainless Steel Hex Cap Screw
3 2 153818 1/4” Stainless Steel Flat Washer
4 2 153817 1/4” Stainless Steel x 1” OD Flat Washer
5 2 153819 1/4” Stainless Steel Split Lock Washer
6 2 153816 1/4 - 20 Stainless Steel Hex Nut
- 2 101734 15” x 18” Pre-Cut Batting (not shown)
- 1 150778 Fuse & Fuse Holder Kit (not shown)
* Pre-installed on enclosure
SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497
16 AWG
Red/Stripe Speaker Positive (+)
Black/Stripe
Red Not Used
20 AWG
LED
LED
Fuse
Fuse
Green Not Used
Blue LED Positive (+)
Blue
Blue
Yellow
Yellow
Blue
Blue
Yellow
Yellow
• For short-circuit protection, install a supplied fuseholder onto EACH
speaker’s BLUE (+12V) LED power connection lead.
• Connect all BLUE (+12V) leads together (parallel) and connect to a
switched +12V supply. Connect all YELLOW (GRD) leads together and
connect to a negative ground or to the NEGATIVE battery post.
• We recommend activating the speakers’ LEDs thru a lighting circuit that
supplies +12V via an existing switch. If an existing switched circuit is
not available, you may install a dedicated toggle/rocker style switch that
Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.
Speaker Negative (-)
Diagram shows one speaker pair of
LED circuits connected in parallel.
[GND ]
[+12V ]
Fuse
Page 2 • JL Audio, Inc., 2017
Continued on Next Page
SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497
POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio MX280/4. The diagram below shows the recommended crossover settings for the MX280/4. For a detailed description of the amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.
Page 3 • JL Audio, Inc., 2017
Continued on Next Page
SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497
STEP 1
The following steps show the installation
procedure for the driver’s side only, but the
procedure is the same for both sides.
Empty the driver’s side of the vehicle.
STEP 2
Remove the two indicated factory bolts.
STEP 3
Cut the Template from Page 7 of this manual.
Align the lower holes in the Template to the
factory holes in the vehicle, and secure using
the factory bolts removed in the previous step.
The bottom of the Template should be parallel
with the horizontal edge of the plastic panel,
as shown.
STEP 5
Using a 1-1/8” hole saw, enlarge the hole drilled
in the previous step.
STEP 6
Pass the cable exiting the enclosure through
the hole in the plastic panel. Position the
speaker enclosure flush against the kick panel,
allowing the grommet to sit in the drilled hole.
Secure the enclosure using a factory bolt
through the lower hole in the enclosure, as
shown.
STEP 7
Using a 1/4” drill bit, carefully drill through the
upper hole in the enclosure, through the
plastic panel, to the exterior wheel well area.
STEP 4
Using a 1/8” drill bit, carefully drill through the
indicated mark on the Template, through the
plastic panel, to the exterior wheel well area.
Remove the factory bolts, and remove the
Tem plate.
Page 4 • JL Audio, Inc., 2017 Continued on Next Page
STEP 8
Slide a 1/4” Flat Washer over a 1/4 - 20 x 1” Hex
Cap Screw, and pass the assembly through the
hole drilled in the previous step, as shown.
SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497
STEP 9
From the exterior wheel well area, slide a 1/4” x
1” OD Flat Washer, a 1/4” Split Lock Washer, and
a 1/4 - 20 Hex Nut over the 1/4 - 20 x 1” Hex
Cap Screw, and fully tighten.
ST EP 10
Route the cable as necessary. Refer to Page 2
for wiring information.
ST E P 11
Reinstall the indicated factory bolt.
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!
Page 5 • JL Audio, Inc., 2017
Place a 15” x 18” Pre-Cut Batting inside the
enclosure.
STE P 12
Connect and install the speaker. Remove the
adhesive backing, and install the JL Audio logo
badge.
Repeat the process for the passenger side.
Note: For optimum performance, we
recommend applying the included Foam Strips
(or sound damping material) to surrounding
plastic panels to reduce unwanted vibrations.
RECOMMENDED SUBWOOFER SOLUTIONS
The SB-POL-RZG2/10TW3 and SB-POL-RZG2R/10TW3 Stealthbox® subwoofer enclosures are also available
for your vehicle. The weatherproof enclosures are designed for a perfect t and house a premium JL Audio
subwoofer.
SB-POL-RZG2/10TW3 SB-POL-RZG2R/10TW3
SKU# 94620 SKU# 94631
®
(954) 443-1100
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox®” and the Stealthbox logo, and “How we play®” are registered trademarks of JL Audio, Inc.
“Ahead of the Curve” and its respective logo are trademarks of JL Audio, Inc.
Printed in USA • ©2017 JL Audio, Inc. • For more detailed information please visit us online at www.jlaudio.com.
JLA-SKU# 011497 • ver. 09.26.2017 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
www.jlaudio.com
This page is intentionally left blank.
SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497
Page 6 • JL Audio, Inc., 2017
TEMPLATES
Carefully cut out the templates along the indicated lines.
SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497
D
-
r
i
l
e
l
l
H
o
o
H
l
l
i
r
D
-
e
l
l
e
-
D
r
i
l
l
H
o
o
H
l
l
e
l
i
r
-
D
DRIVER SIDE TEMPLATE
B
o
-
l
t
e
l
A
o
l
i
H
g
t
n
e
m
n
g
D
-
r
i
l
e
l
l
H
o
o
H
l
l
i
r
D
-
e
l
l
e
-
D
r
i
l
l
H
o
o
H
l
l
e
l
i
r
-
D
i
n
m
e
n
t
H
l
o
A
l
e
t
l
-
o
B
B
o
-
l
t
e
l
A
o
l
i
H
t
n
e
m
n
g
g
n
m
e
n
t
H
i
l
o
A
l
e
t
l
-
o
B
PASSENGER SIDE TEMPLATE
B
o
-
l
t
e
l
A
o
l
i
H
g
t
n
e
m
n
g
i
n
m
e
n
t
H
l
o
A
l
e
t
l
-
o
B
B
o
-
l
t
e
l
A
o
l
i
H
g
t
n
e
m
n
g
i
n
m
e
n
t
H
l
o
A
l
e
t
l
-
o
B
Page 7 • JL Audio, Inc., 2017
Loading...