INSTALLATION GUIDE
for the
SB-GM-C7CP2/10TW3
SKU# 94604
2014 & Up Corvette C7 Stingray
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to per form the installation yoursel f, it is abso lutely vital
that the Stealthbox® be properly mo unted to the vehicle according to
these instruc tions. Failure to mount the enclosure properl y presents two
problems:
1) The sub-bass perfor mance will suffer due to the movement of th e
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure present s a serious safety hazard in th e event of a
collision or sudden deceleration.
INSTALLATION
DI FFIC ULT Y:
ESTIMATED TIME:
1/2 H OUR
Enclosure Type: Sealed
Driver Type: 10TW3-D4
Nominal Impedance: 4 ohms
Continuous Power Handling: 800 watts (RMS method)
Continued on Next Page
1
5
OUT
OF
SB-GM-C7CP2/10TW3 INSTR_SKU# 011382
INCLUDED HARDWARE
Continued on Next Page
Page 2 • JL Audio, Inc., 2016
SB-GM-C7CP2/10TW3 INSTR_SKU# 011382
POWER RECOMMENDATION
JL Audio recommends high quality amp liers such as the JL Audio HD750/1. The diagram below shows the recommended crossover settings for the HD750/1. For a detailed description of the
amplier settings, consult the own er’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the p erformance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplier. Other kits are availab le should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both
channels of the amplier. JL Audio recommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2016
SB-GM-C7CP2/10TW3 INSTR_SKU# 011382
Page 4 • JL Audio, Inc., 2016
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Au dio coaxial and component syste ms will t in the factory spea ker locations of you vehicle.
Front Speaker Size / Location: 10”- Front Doors
Fits JL Audio M odels: TR650-CXi, TR650-CSi, C2-650x, C2-650,
C3-650, C5- 650x, C5-650, & ZR650 -CSi
Rear Speaker Si ze / Location: 6-1/2”- Side Panels
Fits JL Audio M odels: TR650-CXi, TR650-CSi, C2-650x, C2-650,
C3-650, C5- 650x, C5-650, & ZR650 -CSi
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, and “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the
Curve”, its respective logo, and “How we play” are trademarks of JL Audio, Inc.
Printed in USA • ©2016 JL Audio, Inc. • For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
www.jlaudio.com
JLA-SKU# 011382 • ver. 09.16.2016 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!
How we play.
™
SB-GM-C7CP2/10TW3 INSTR_SKU# 011382
STEP 4
Connect speaker cable to the terminal cup on
the enclosure, place the Stealthbox into position, and rout the cable as necessary.
Thread the two bolts removed in the previous
step through the holes in the Brackets, and
firmly tighten. Snap the two bolt covers back
into place.
STEP 3
Empty out the trunk of the vehicle. Carefully
unclip the two tie-down hook bolt covers, and
remove the bolts.
STEP 2
Pictured is the Stealthbox® with both Brackets
attached.
STEP 1
Secure each of the Brackets to the threaded
inserts on the bottom of the Stealthbox® using
a 3/8 - 16 x 1-1/4” Hex Bolt, 3/8” Lock Washer,
and 3/8” Fender Washer as illustrated.
Loading...